Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Metal working question.....

Posts

Metal working question.....

#1

Metal working question.....

Barry Irby

A friend of mine needs to drill a hole through a rack gear. Its a metal track that has teeth like a gear. The teeth are about an 1/8" apart at the bottom and a 1/4" at the top. Need To drill a counter bored hole. The actual hole is about an eighth and the counter bore is about 5/16". The problem is the drill bit for the counter bore grabs the shoulders on the teeth of the gear and runs all around or snaps the bit. Is there a metal working bit that has a counter bore built onto it so the smaller portion would act as a guide?

The idea is that the head of the screw needs to be recessed below the teeth of the pinion gear.

He's trying to do this on the job without the benefit of a drill press.

Any suggestions?

Re: Metal working question.....

#2

Re: Metal working question..... *LINK*

John in NM

Try a #4 center drill. Still tough to do without a drill press, but he might get away with it.


Center drills

Re: Metal working question.....

#3

Re: Metal working question.....

Ray Thompson

Short answer is yes but it won't work well in that application. Drill from the bottom and c'bore from the top

Ray

Re: Metal working question.....

#4

also

Ray Thompson

the chance of drilling from the top on location without a drill press borders on nil.

Ray

Re: Metal working question.....

#5

Re: Metal working question.....

Lars Parrington

drill a 5/16" hole through a block of wood. clamp the block to the gear rack, centered over the smaller hole. drill the counterbore.

Re: Metal working question.....

#6

Re: Metal working question.....

walta

If you are limiting yourself to hand held tools, I say use a grinding stone in Dremel type tool. This plan is much less likely to destroy the gear.

Walta

Re: Metal working question.....

#7

You sure you can drill it?

Dick Coers

Might be case hardened? Then you need some hard drill bits and they will definitely not like side loading on a gear tooth. There are piloted counterbores, but the pilot on that diameter will not be long enough.

Re: Metal working question.....

#8

Re: Metal working question.....

Keith Newton

I think a step-drill is the term for that kind of bit.

Re: Metal working question.....

#9

step drill

Jerry Gibbs

step drills are meant for sheet metal and will drill about 1/8" before the next step.

Re: Metal working question.....

#10

Re: Metal working question.....

Lars Parrington

Additionally, if the drill bit is still too grabby, you can regrind it a bit. I'd suggest trying a zero degree rake angle at the cutting edge (this could be similar to a microbevel on a sharp tool, but at 90 degrees, and you could probably grind it in the field just using a small file), and/or reducing the pointiness of the bit (as in make it look more like an end mill).

Note that this regrind is only recommended in combination with the wood block recommended above.

Re: Metal working question.....

#12

Yes, But there are lots more under that heading

Keith Newton

I have several different kinds in my tool drawers.

Try a google search, then just click the image link.

Re: Metal working question.....

#13

Re: Metal working question.....

TomD

You can get a nice drill press off craigs for about 20 bucks. By nice I am talking about a unit that at most costs maybe 100 new. I needed one a while back for some scavenged parts for a project and in Toronto there was one for sale at almost every exit of the HWY. I haven't done the project yet but have been happily using the DP since. I have a Buffalo Forge massive unit, but it will kill you if you make an all too easy mistake.

Re: Metal working question.....

#14

Re: Metal working question.....

John K Jordan

I would use my milling machine. A machine shop should be able to to this for very little cost. If the part is hardened it may be very difficult or impossible to do this at home.

If you really, really need to use a hand drill (e.g. if the part is too big or fastened to something big, you could drill a guide hole in a block of steel or aluminum then clamp this to the part. A countersink guide could also work. You might need to clamp the part and clamp the hand drill onto a sliding jig (build your own drill press) to keep things from jumping around.