Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

bolting a sculpture to a base

Posts

bolting a sculpture to a base

#1

bolting a sculpture to a base

eliot feldman

I want to bolt a sculpture to a wooden plank. The sculpture is about two feet high and the plank is about two inches thick. The sculpture already has two holes drilled into it about three inches deep by 1/4 in diameter for two bolts. You have to assume that the holes are not perfectly parallel in space ( for the mathematicians out there, the direction cosines are not the same.) The question is how to drill the holes in the plank so that two bolts will go into the sculpture nicely. The idea is to epoxy them into the holes. I believe the problem is similar to what certain chair makers face when lining up spindles, which I understand is more or less done by eye. But spindles can flex a little, but bolts don't. I know I can drill the holes over size in diameter so there is room for inevitable error, but I am hoping for something more or less foolproof. Any ideas?

Re: bolting a sculpture to a base

#2

Re: bolting a sculpture to a base

Joseph Mulherin, sr

Eliot, cut off the head of a bolt, sharpen it on the end, screw the bolt into the statue leaving about 1/4" exposed, position it onto your blank evenly all around then pressure the statue hard onto the blank leaving some marks where the holes would be drilled. Then drill with a Forstner bit large and deep enough for a fender washer embeded about 1/2" into the blank, screw a good stainless bolt and washers into the hole, tighten and you have it mounted.

Re: bolting a sculpture to a base

#3

Re: bolting a sculpture to a base

Barry Irby

1/4" bolts are plenty flexible. I'd use a short piece of "Ready Rod" or All Thread and insert it into the sculpture dry Leaving just less than the thickness of the base exposed. and look at the alignment. If they looked parallel and "vertical" I would epoxy them into the statue and proceed as Joseph described. If they are not parallel, I would bend them to make them parallel. Depending on how sturdy the statue is, I might bend them in place, or bend then in a vice and reinsert them.

If you decide not bend the bolts and they are crooked, remember that if the rods project out two inches, that is where the hole in the plank will exit the plank and the entry points under the statue will be different. Use shorter bolts that just barely project from the statue to make the entry holes and then eyeball the angles.

I'd probably start with 5/16" holes int the plank and counter-bore them enough for the washer and nut. If I had to I would wallow out the holes a bit.

Re: bolting a sculpture to a base

#4

Re: bolting a sculpture to a base

Hank Knight

How big are the holes in the bottom of the statue? If they are large enough, epoxy threaded inserts in the holes and make sure they are perpendicular to the base. For that matter, you could epoxy some threaded rod in the holes, making sure they are perpendicular and parallel. If the holes aren't large enough to allow some wiggle room, enlarge them with a dremel tool and a carbide or a diamond burr.

Re: bolting a sculpture to a base

#5

Re: bolting a sculpture to a base

Brian Roberts

Need more info first......

Of what material is the sculpture made?

Is the bottom flat?

Are the existing holes perpendicular to the bottom?

Re: bolting a sculpture to a base

#6

Re: bolting a sculpture to a base

eliot feldman

This is what i"ll do. What you're really saying in effect is to make sure the bolts coming out of the bottom of the sculpture are indeed parallel in space and perpendicular to the board. This is clearly preferable to worrying about how to drill angled holes to match whatever angles are there if they are not parallel. And threaded inserts are superior because , then, one can un-bolt it if necessary. Thanks.