Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

unusual cutting techniques *LINK*

Posts

unusual cutting techniques *LINK*

#1

unusual cutting techniques *LINK*

john lucas

I hope this doesn't get into a mud slinging thing but I was watching videos this morning when I couldn't sleep and came upon this one. So I have 2 questions for the crowd. When He's ripping the thicker board he's using a short fence and feeding the wood twice. My question is, what would be the advantage of a short fence. I have always used a long fence and fed the wood all the way through the blade using a narrow push stick. I can see if you don't use a push stick it would be safer. I should say for ripping tall narrow stock I use a push stick that is a saddle over the fence so the push stick can't rock into the blade.

Later in the video he's using a chop saw (Festool I think) Instead of lowering the blade into the work and feeding it through he is making multiple shallow cuts. Is there an advantage to doing this.

Again I'm not trying to slam his technique just trying to learn from it.


https://www.youtube.com/watch?v=SIwAHJ3ZY40

Re: unusual cutting techniques *LINK*

#2

Re: unusual cutting techniques

Barry Irby

I don't have that fence or even that type of fence. Can't shorten my Bies., but I have made sort of similar cuts. My out feed on my saw is limited by a garage door about five feet away. (tiny shop blues) Either I have to open the door or do a double rip. I have done it many times. Easier to flip the stick that to open the door for one or two cuts. But, I don't pull the piece back, at least I don't think I do. I lift it off the blade. My bad, but no upper blade guard. I keep the blade just above the work piece. For me, this is quick, but does not produce the best cut. In well behaved wood I get a pretty good, straight cut without an obvious step in the cut. In rascally wood, not so good.

It seems the pulling back would be and invite to a kick back. The short fence might be good to limit the side pressure on the blade.

Re: unusual cutting techniques *LINK*

#3

Re: unusual cutting techniques

john lucas

Barry I thought the short fence might help when ripping reactive wood as well.

Re: unusual cutting techniques *LINK*

#4

Ellis Walentine

Re: unusual cutting techniques

Ellis Walentine

Short fences are commonly used in Europe. When you think about it, the fence is only important until the cut is made, and a short fence allows reactive wood to move away from the blade. The Delta Unifence was designed with the ability to retract the fence rail so that it stopped at the end of the blade, or anywhere else.

I personally am not comfortable with any tablesaw operation that involves pulling the workpiece backward, at any time in the cut. The guy in the video is clearly an expert with his techniques and still has all his fingers, but I'd be very wary of the learning curve.

I haven't seen the multiple-cut technique on the miter saw and am not clear on its advangtage over simply plunging and pushing the saw through the cut. I guess the feed resistance is less for each individual partial cut, but, as with the double ended tablesaw ripping technique, I'd think there would be a greater likelihood of a ratty cut surface, which doesn't matter much if you're going to edge sand it afterward.

Techniques aside, my comment on this video is "what price novelty?" What a huge amount of work for a cutting board.

Ellis

Re: unusual cutting techniques *LINK*

#5

The chop saw cut...

John in NM

I do something like that now and then, usually when cutting thick wide lumber that I expect to pinch the blade. If you're only cutting 1/4" at a time, the next pass will widen the kerf where it started to pinch. If you were taking a full bite with the saw, the blade can get locked right in the kerf.

The problem doesn't really come up much with non-sliding chop saws due to their limited cutting width. The guy in the vid doesn't really need to be doing it for that cutting board, it's probably just habit at this point.

Re: unusual cutting techniques *LINK*

#6

You mean our work is supposed to be profitable ?


Re: unusual cutting techniques *LINK*

#7

Re: The chop saw cut...

john lucas

my thoughts on the chop saw technique is that it produces less resistance and is less likely to move the work out of alignment since he doesn't have it clamped down. However if it does happen to slip at all the next pass will have more resistance and might pull it into the work or at best leave a saw mark that requires more clean up afterwords.

I do like the cutting board but like Ellis said. I would have to make that for a friend or relative to justify the time. Of course that describes most of my work.