Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Ripping on the table saw

Posts

Ripping on the table saw

#1

Ripping on the table saw

Joe in a Cleveland suburb

Bill's Spice Box prompted this question. I was going to post this as a reply to Bill's most recent Spice box update, but didn't want to hijack his thread.

I've been using a table/cabinet saw for 20+ years now and one operation that still makes me nervous is ripping. More and more I try to do all the ripping I can on the bandsaw. Sometimes of course, it doesn't make sense to.

Bill shows ripping off the molded pieces of stock from the wider board once routed. This past weekend I ripped 6 1"X12"X6' #2 pine boards into 2" wide boards (making pickets for my wife's garden fence). On two occasions the board warped so bad while ripping it pinched the blade and I had to shut the saw off. On more than one occasion knots shot off like bullets.

I always try to be safe. I use a Bessy splitter with pawls, a big push stick, and feather boards all when I can. I always stand clear of kick backed projectiles as much as possible. I believe my saw and rip fence are tuned/set up properly to avoid pinching the stock between the blade and rip fence. I admittedly don't use a blade guard. I use/have an out feed table attached to the saw. The blade height I tend to keep high enough so the gullets are exposed.

I am left handed. But I am never sure if I should be pushing the stock through with my left or right hand. When I used to play baseball as a kid, I could bat left or right handed - either way felt natural (never could hit the damn ball though...). Same with pushing the stock through in regards to left vs. right handed.

I tend to stand left of the blade and push with my right hand (using a push stick). That doesn't seem safe as my hand/arm passes over the blade. If I stand to the right of the blade and push with my left hand, I feel as though the pushing motion might actually be pushing the stock to the left a little too.

So, I was going to ask Bill these questions in his post, but thought I'd ask everybody -

When you rip on the table saw:

  • Do you stand to the left or right of the blade?

  • Do you push the stock through with your left hand or right hand?

  • Do you use a feather board or two?

  • Do you use a blade guard?

  • What do you use as a push stick?

  • Are you left or right handed?

  • What about blade height?

  • How much thought do you put into "is what I'm about to do safe?"

  • Just curious I guess as to what some of you do regarding ripping safely (especially narrow stock) and how you handle safety concerns.

    Thanks for any replies.

    Re: Ripping on the table saw

    #2

    Re: Ripping on the table saw

    John McGaw

    Do you stand to the left or right of the blade?

    I stand on the left of the blade and fence so that I can see how the stock is moving so I can keep it in contact with the fence. If the blade was on the other side of the blade (my Robland can do it either way) I'd reverse the position.

    Do you push the stock through with your left hand or right hand?

    I use the closest hand which is the right in most cases.

    Do you use a feather board or two?

    When it seems advisable I use magnetic roller units to hold the stock down and/or to hold it toward the fence.

    Do you use a blade guard?

    No. And, to be honest, I seldom use the splitter knife which my saw has but which is a PITA to adjust with blade changes.

    What do you use as a push stick?

    I usually use a plastic commercial stick when it a stick seems to be advisable.

    Are you left or right handed?

    Right.

    What about blade height?

    At least high enough to clear the gullets although when ripping extra thick stock with multiple passes and from both faces this is impossible (I guess you'd properly call this resawing).

    How much thought do you put into "is what I'm about to do safe?"

    Quite a bit but probably not enough. I still have all my digits and the worst injury I've suffered in the shop over a couple of decades came from a dropped scalpel-sharp chisel embedding itself in my instep.

    Re: Ripping on the table saw

    #3

    Re: Ripping on the table saw *LINK*

    Jesse Cloud

    I'm not Bill, but that never kept me from shooting off my mouth before. ;)

    Firstly, I would not cut warped lumber on a tablesaw - just asking for trouble. Much safer on a bandsaw. I can also clamp it down firmly and cut it on the tracksaw.

    I always use a splitter, except when it is physically impossible.

    Whenever something doesn't feel safe, I stop right then and rethink the process. ;).

    I always use a push stick (except on sheet goods).

    For ripping narrow strips, I use the Gripper. Feels weird at first, but it makes some things much safer.

    Lastly, I think about safety a lot. At my age, I'm not sure I could recover from a major accident, and I still owe the wife half a house full of furniture. :D

    Be safe - we want to see lots more of those great projects you make!!


    Gripper

    Re: Ripping on the table saw

    #4

    Re: Ripping on the table saw

    Larry Clinton At Frankfort, (Central) Indiana

    I feel absolutely safe when ripping on the table saw. I use Grr Ripper's for EVERY cut. I also have the Micro jig splitter installed on my saw's insert.

    I always stand on the same side of the fence as the blade so I can see what is going on. The saw "Off" switch is conveniently located so I can hit it with my leg and shut it off. I have had boards warp and grip the splitter tight enough I had to remove the splitter and spread the cut open to remove it, I still did not ever lose control. I have also stalled the 3 hp motor when a board closed on the blade and splitter. With the Grr Rippers I have never lost control or had a kickback!

    When cutting short boards I feed with my right hand, with longer boards I use both hands feeding with one over the other, never releasing pressure on the item being cut.

    I can adjust the Grr-Ripper so that I can control a board as narrow as 1/4" with no problems. I even use them for breaking down 4' X 8' sheet stock. I can do a far better job ripping on my Unisaw than on my MM-16 band saw, the only time I use it to rip is if I have a very uneven board edge, then I either chalk line or mark with a straight edge to rip it, then join that edge and use the table saw for all remaining cuts.

    Over the years I have gotten the Grr Ripper into the blade a few times due to it not being set up correctly or me not positioning it properly on the material ~ I keep spare parts and replace the parts as necessary. Though the parts aren't real cheap they are sure cheaper and a lot less painful than an emergency room.

    Re: Ripping on the table saw

    #5

    Re: The pushing hand

    Yonak

    Always push with the hand that's between the blade and the fence and guide with the other. Otherwise you're asking for trouble. If you're to the left of the blade and the fence that will be your right hand.

    Re: Ripping on the table saw

    #6

    Re: Ripping on the table saw

    Jerry Gibbs

    I was taught that when it is safe to do so, use your hands and not a push stick. You have less control with a push stick. Obviously when getting close to the blade, switch to the stick. I have a set of Grr Rippers and use them mainly for narrow cuts. I think I will try to use them more. An advantage to the Grr Rippers is that you can control both sides of the cut all the way past the blade.

    Re: Ripping on the table saw

    #7

    Re: Ripping on the table saw

    Barry Irby

    I am not Bill either, but one thing he does is use a 7 1/2 or 8" blade that is very thin and 40 teeth if I remember. If you have a ten inch saw, using an 8" blade will cost you and inch of depth capacity. Bill uses a quality Blade by CMT blade, I think. I have used a really cheap 7 1/2" skillsaw blade and the difference it makes in the effort it takes to feed the wood and the loading of the blade is astounding. The blades Bill recommends are reasonably priced, Maybe forty to fifty bucks and well worth it.

    Re: Ripping on the table saw

    #8

    Re: Ripping on the table saw

    Bill Tindall, E.Tn.

    When you rip on the table saw:

    •Do you stand to the left or right of the blade? LEFT, fence to right of blade

    •Do you push the stock through with your left hand or right hand? Right thumb pushing forward, right index finger pushing down, fence rides between index and middle finger to trap hand on the fence (I have a narrow vintage Delta Unisaw fence) left fingers pushing toward fence and down until this hand reaches table edge and then it stops. I never get left hand past table edge.

    •Do you use a feather board or two? Almost never

    •Do you use a blade guard? Sometimes

    •What do you use as a push stick? Sometimes but as seldom as I can get by with. Safe ripping is all about control. There is no control of a board on the end of a stick. I will only use a push stick on a very narrow cut.

    •Are you left or right handed? right

    •What about blade height? teeth tips just exposed

    •How much thought do you put into "is what I'm about to do safe?" By now it is subconscious what is safe and not. After using a 7 1/2" thin blade for the past 10 years I am stressed ripping with a full kerf 10" blade. The 10" bade is a lot more scary due to more force of blade on wood.

    In the case of your 2" strips I would have cut them without a push stick with hands as described above. My hands provide firm control of the piece. It would be rare for a blade to stall with the teeth just poking above the board for they will cut clearance in a bind. If a 7 1/2" blade binds there is vastly less force on the wood to push it out of control.

    Pieces of knots occasionally fly out but again the acceleration is less on a small blade. I don't stand behind the blade in any case so anything that flies by usually misses body parts.

    Re: Ripping on the table saw

    #9

    Re: Ripping on the table saw

    don stephan

    Joe

    there are blade guards that can hang from the ceiling or from a tube extending to the right of the table saw.

    Not at all surprised #2 pine had internal tension. It's also not likely to last too long outside.

    Re: Ripping on the table saw

    #10

    Re: Ripping on the table saw

    William Duffield

    Do you stand to the left or right of the blade?

    To the left, unless I'm cutting a bevel, then I stand to the right of the blade and fence. My saw is left tilt.

    Do you push the stock through with your left hand or right hand? It depends on the width of the stock and the cutoff. If the cutoff is narrow, I use my right hand. If the cutoff is wide, I use both hands.

    Do you use a feather board or two?

    Not usually.

    Do you use a blade guard?

    Only when I'm cutting a lot of stock. Then I use it to collect dust. Because I can't see the cut with the blade guard in place, I also use JessEm Clear-Cut stock guides attached to the fence.

    What do you use as a push stick?

    I'll save that answer for last.

    Are you left or right handed?

    Left

    What about blade height?

    I raise it just high enough to expose the whole carbide tooth at the top of the cut.

    How much thought do you put into "is what I'm about to do safe?"

    See Bill Tindall's answer. Also, I don't use the table saw when there are distractions moving around or talking (or barking) in the shop. Also, I have a SawStop, so I did a lot of thinking before I purchased it.

    I make my own modular push sticks.


    The long nose insures that the blade doesn't lift the stock off the table which would make it a lot easier for the blade to kick it back.

    These work very well for ripping very narrow stock and also for ripping thin stock. The attachment between the stick and the handle is a loose tenon, so when I wear out the stick, I just replace the stick and put the tenon on the next one. The push block is also a Domino loose tenon, so when I wear it out cutting narrow stock, I replace it. When I'm cutting thin stock (ref. above picture) I retract it with a plane hammer. When I'm cutting thicker stock, I extend it with a plane hammer.




    This stick and these tenons have been cut a few times, but aren't quite ready to be replaced.

    Re: Ripping on the table saw

    #11

    Re: Ripping on the table saw

    TomD

    I'm right handed, I stand to the left of the saw and use both hands with the right hand going between the blade and the fence when it is safe to do so, and the left hand forward in a supports role. I have rippers, and blade guards. I think the right blade guard is a huge safety factor. I use european saws, and technique, which are superior to US saws. The US saws are a kludge of various advances cobbled onto a saw that hasn't changed since the Model T Ford was in production, well 1939 anyway.

    Never reach behind the blade, always use a push stick or carrier. Be aware that the length width and thickness of the piece are all factors in kickback.

    IN CASE YOU don't know. When it comes to the blade pinching, the forward and aft angle of the table top is a factor along with the table being out of parallel with the arbor. This will cause problems when the blade is inclined.

    I know when to say no and use other methods. Pushing a tool to do things it can't safely do is not worth it, but it can be difficult to know where the lines are.

    While I prefer to rip on a bandsaw when possible, be aware that bandsaws can be dangerous also. The unlimited geometry is dangerous. Try cutting yourself in half lengthwise on a table, saw, or sawing off a leg in a single cut. I have read reports that more accidents are caused by bandsaws, purportedly due to the sense of safety they engender. Hard to know how on would know that. And there are a buch of stupid cuts that one can get suckered into on them.

    Re: Ripping on the table saw

    #12

    Ellis Walentine

    Re: Ripping on the table saw

    Ellis Walentine

    I pretty much agree with the others' advice ...stand to the left, push with the right... but I only use a push stick on rips that are narrower than about four or five inches. I have a variety of pushsticks (vaguely resembling a hobnail boot) that I hastily bandsaw from scrap plywood, of several different lengths and thicknesses, with a "heel" near the rear that engages the work. This design allows you to apply forward and downward pressure simultaneously, as William's design also does. I tried the Grrippers many years ago when they first came out, but I am nervous about trusting friction to drive the workpiece, especially if the rubber friction faces become coated with dust or other contamination; I'm more comfortable with the more positive mechanical engagement of my pushsticks. Regarding safety awareness, as we used to say in every issue of the magazine, if you don't feel comfortable with anything, don't do it. Words to live by.

    On another note, Frank Klausz never rips anything thicker than about an inch and a half thick on his tablesaw; he uses his bandsaw.

    Ellis

    Re: Ripping on the table saw

    #13

    Additionally- hand position

    Bill Tindall, E.Tn.


    I have an old style narrow fence. A cabinet shop manager taught me this finger position for ripping stock. Depending on the thickness of the wood I may have the fence between first and second finger on thicker stock. With the hand locked to the fence in this way it is less likely to stray, or be pulled toward the blade.

    Safe ripping is all about keeping the piece being ripped under control. For me this hand position will control the piece of wood and the thin small blade reduces the cutting force on the wood that could displace it from a secure ripping position.

    I use a push stick on very narrow stock to push lumber the last few inches past the blade. A collection of sticks hangs within easy reach of the saw.

    Re: Ripping on the table saw

    #14

    Re: push sticks

    William Duffield

    Before I got the tenoning machine, I sawed my push sticks out of plywood on the bandsaw. I made them the same basic shape as the one I show in the pictures, but the handle wasn't as comfortable. The little block that does the actual pushing, I glued into a dado I cut in the body of the stick. It is that shape that is most important. The modular design that uses the loose tenons is just to make them easier to build and repair. I can invest more time in comfortable handles if I don't throw the handle away every time the body of the push stick sacrifices itself for my fingers. I use the same handle design for jointer pushers, router table pushers and leg taper jigs, which I've shown here before. I cut out and shaped a batch of handles, and put the extras away for future use.

    While push sticks are just one more reason to add to your list of things that you can add to your list of justifications for the purchase of a Festool Domino, It is not necessary to have one to make push sticks that work like mine. The mortises and the tenons can be cut with your router, or you can even use dowels to hold the pieces of the push stick together.

    There is one other design factor to consider, to make them even safer, or at least increase your sense of safety. You might worry that the board you are pushing could somehow get away from the push stick and kick back anyhow. If so, the push stick could drop down to the saw table and your hand could drop down into the blade. There's a simple solution: Make the stick part of the push stick taller than your blade exposure. While I can't imagine this scenario occurring in my shop, I know that my SawStop will protect me if it did. If this problem or its fix is not clear to anyone, let me know, and I'll go build the push stick that solves the problem, and take pictures of the building and use of the stick. Adding multiple layers of safety to any dangerous operation is always a good practice.

    Re: Ripping on the table saw

    #15

    What I do...

    John in NM

    I'm right handed, stand square to the saw and slightly left of the blade (and thus the trajectory of anything spit out). Saw is an old Unisaw with no guard.

    Push stock with a push stick in my right hand and a splitter stick in my left. The splitter stick gets jammed into the kerf behind the blade to hold the kerf open if it starts to pinch the blade - usually a bad pinch is far stronger than the wood of the stick, so it only helps a little with very unruly wood - like quickly dried construction lumber or Euro beech, and for some reason hard maple.

    Splitter stick is also handy for holding the stock down/in place if I have to reach down and turn off the saw.

    This set up works well for me probably because I'm tall enough to reach over the saw comfortably with that second stick and still never get near the blade.

    Re: Ripping on the table saw

    #16

    Re: I forgot one thing

    William Duffield

    Instead of a splitter, my saw has a riving knife. (All table saws sold in the U.S. are now equipped with one of these, because they are so much safer than splitters, and you won't be tempted to remove it and hang it on the wall.) I never have to remove it unless I'm swapping the blade for one with a different thickness kerf, as it is always the height of the blade and the thickness of the kerf.

    I did have to make a slight modification to one of mine, because, as delivered, it was just a smidgen higher than the kerf cut by the saw blade.

    Re: Ripping on the table saw

    #17

    Re: Ripping on the table saw

    Hank Knight

    Like most everybody else, I stand to the left of the blade and push with my right hand. I usually raise the blade enough to clear the gullets, but sometimes, especially ripping narrow stock, I feel uncomfortable with that much blade exposed. In those cases, I raise the blade high enough to clear the carbide teeth. I always use a splitter. I use a thin kerf 10" ripping blade most of the time. I have full kerf rip blade but I seldom use it.

    Several years ago, I had a bad kickback with my Unisaw ripping a 2X4 using a push stick. I had an after-market splitter in place, but it failed to prevent the kickback. That accident taught me two things:

    (1) Accidents can and do happen, even when you're following accepted safety practices. Most people get hurt on tablesaws, not by carelessly running their hands into the blade, but by experiencing a violent event, like a kickback, that jerks their hand into the blade. I figured I was lucky with only a major bruise and that it was just a matter of time before something like that happened again. I sold my Uni and bought a SawStop.

    (2) Push sticks are not very safe. Kickbacks happen when the back of the work piece lifts up and comes into contact with the teeth at the rear of the spinning blade. Keeping the stock flat on the saw table is essential to preventing kickbacks. Push sticks are ineffectual in keeping the back of the work piece flat on the saw table, they only control the front end of the work piece. A push "shoe" (for lack of a better name) like Sir William and Ellis describe, works much better. It exerts pressure horozontally to push the work piece through the blade and also, PERHAPS AS IMPORTANTLY, vertical pressure on top of the work piece to keep it flat on the saw table. I learned about push shoes on this Board. Thanks Carolyn.

    I use a push shoe almost exclusively now. There are other ways to address the issue - feather boards and after-market devices like Board Buddies and such, but push shoes work well, cost almost nothing and are easy to use. The only downside for me is that they interfere with the use of my Excaliber blade guard when ripping narrow stock, which is probably when I need it most.

    Hank

    Re: Ripping on the table saw

    #18

    Re: Ripping on the table saw

    TomD

    "(2) Push sticks are not very safe. Kickbacks happen when the back of the work piece lifts up and comes into contact with the teeth at the rear of the spinning blade. Keeping the stock flat on the saw table is essential to preventing kickbacks. Push sticks are ineffectual in keeping the back of the work piece flat on the saw table, they only control the front end of the work piece.

    This presupposes one is running pieces that are too short through the saw. If you had a four foot board by the time you got around to pushing the last of it through with sticks there would be plenty beyond the blade to stabilize with the second stick. Sticks do have the advantage of being able to keep both your hands and body well back from the blade. The various things that look like hand planes, while excellent in their place will not have your body out of the way wwhen that chuck comes back as it may some day.

    I did once get hit by a flying piece of cherry that was just a little too thick, wide and short. It looked like a safe piece, but it hit with the force of a bullet out of a 22. One of the dangers of working by oneself is that there isn't anyone there to chew you out when you repeat the setup that put the guy you replaced in the hospital. You have to make all your guesses on your own dime, and even a very cautious and smart person may make a bad guess.

    Other than walking away, increasingly I rip boards half way through, then flip them and rip the other half. The result is not as smooth always, but it I have never had a close call. And none of my shops have abundant space (left) or high ceilings. I just put up with the inconvenience.

    One thing I see a lot of country carpenters do, that I have experimented with, is ripping wet and otherwise nasty wood without the fence. Scary as heck to see someone do, and I think these guys have never seen a 3hp saw. But some of them have been getting away with it for 40 years or more... I have tried it on my dad's beaver, totally do not recommend it. But it is a further part of my education in how an underpowered saw can save your bacon. There is a saying that a sharp knife is safer than a dull one. And a similar thing applies to saw power. But at times I wonder whether the people who say these things have every used a sharp knife. Sure, used carefully it allows precision, and you don't have to commit much force, but once it starts cutting you, you would prefer that it was dull as far as the damage done is concerned. Same thing with 3HP. Makes the work easy until it starts working on you.

    Re: Ripping on the table saw

    #19

    Re: Ripping on the table saw

    Joe in a Cleveland suburb

    Thanks everybody for taking the time to respond.

    It sounds like I am doing what I can for safety but can do more.

    1 - I'll take a closer look at the GRR-Ripper device.

    2 - Look more into using a 7-1/4 blade. I have several links saved from here on discussions about it from Bill T. A concern about those is I wouldn't be able to use my splitter I don't think.

    3 - Need to make much better push sticks.

    Below are my push sticks. The 3 on the left are never used. My dad gave me those years ago and I just haven't thrown them out. The one on the top right is sometimes used - keeps my hand far from the blade but not as much control as I would like. The one on the bottom right is used most often. It has a line of red foam on it which helps with control. It also has that little block of wood near the top to remind me to keep my thumb up high away from the blade.

    The first thing I am going to do is make a much better one long the lines of Mr. Duffield's


    Thanks.

    Re: Ripping on the table saw

    #20

    One thing about smaller blades...

    John in NM

    Pay close attention to hook angle. I've used a RAS that someone put a 7 1/4" framer's blade on, and it was truly terrifying. For a table saw you want a hook of no more that 5-10 degrees I would say. When dealing with 10" blades most have such reasonable angles that the question never even comes up - but get into smaller blades and some are very aggressive.

    I would have guessed that the arbor sizes are standardized to prevent this problem, but since I've seen it done there must be ways around it.

    Re: Ripping on the table saw

    #21

    Re: Ripping on the table saw

    Jesse Cloud

    You can make your own simple splitter.

    Start with a wooden zero clearance insert. Lay out lines the width of the blade and going back an inch or so from the blade at max height.

    Make a piece of wood the width of the kerf, round off the leading edge and glue into the slot.

    No pawls, but it will keep the board from closing up.

    Re: Ripping on the table saw

    #22

    Re: Ripping on the table saw

    William Duffield

    Keep the three on the left for posterity, but stick one of these on each one.


    Those things scare the dickens out of me. If you use one, the kicked back board will just be going faster when it hits your hand.

    The other two are reasonably safe. I like your tactile warning block.

    The one I showed feels a little clumsy, because the toe is a little too long for most of the stock I push with it. When I made it, I just used the stick I found. It doesn't affect its function or safety, and it works better for long stock, but you could cut some off the toe for shorter wood.

    A good reason for making an adjustable depth push block becomes immediately obvious (DAMHIKT) when it stops on the edge of the saw table when pushing thin stock.

    Your red padding is a good idea, especially when the last sliver of the push block is eaten by the blade when you are cutting narrow stock with different fence settings. Don't use PSA sandpaper instead. I found it very surprising how little of it can dull the saw blade.

    Something else I do, if I'm ripping a board I don't trust, is put a couple of wedges on top of the fence where I can reach them and shove them into the kerf if it starts to close on the blade.