Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Same project different area as earlier

Posts

Same project different area as earlier

#1

Same project different area as earlier

Gary Smyth

Recap: Installing additional furring to enable cabinets in laundry.

Project dominoed to enable additional cabinetry in laundry. When first addressed the wall had two layers of 1 x 2" furring horizontal at baseboard and ceiling level. Inexpensive paneling basically just hanging with nothing behind. The wall behind is concrete block (some below grade) with outside exposure. Water pipes anchored to the wall in many directions to laundry, bathroom and routed to kitchen. Which I suppose is why the paneling just hung there. Never had a problem with freezing pipes as (perhaps) room air was unimpeded inside the 1 1/2" cosmetic hanging panel curtain.

Question. Now that the water pipes for this section are enclosed (blue tape) is there something I should do before I close up the space? IF I insulate with foam or other stuff one portion of the water pipe will still be attached to the wall. Will enclosing them make matters worse? I would rather not undo all of the water pipe anchors to isolate the pipes as that is a whole other can of worms. I do not want to make additional work. What think you? Can I close up, as is, add insulation, (what type) or (worst case) tear it out and isolate or reroute pipes? Right about now I want it done but want no problems next February.

Re: Same project different area as earlier

#2

Re: Same project different area as earlier

Barry Irby

Gary, where are you? Is freezing a big deal where you are?

If you are in a frost free climate or one with a low risk, you are probably fine. Depending on the severity of the freezes in your area it woudl be better to have insulation behind the pipe but not on the interior side. The insulation would keep the cold out and permit the heat from the living space to keep the pipe warm.

If you are moderately concerned, you could leave the hot side dripping on the coldest nights. This is a twofer. It transports a little warmth into the area and help warm its neighbor, the cold water pipe and it lets the pressure off the system. (In a freezing situation the pressure build up is a critical part of the problem. If the pipe freezes, the ice expands and acts like a piston and blows out something in the system somewhere.) Leaving it dripping requires you remember to do it.

Re: Same project different area as earlier

#3

Barry,  Live in Western PA

Gary Smyth

It gets cold and pipes do freeze. Never had these freeze even when lost power in big ice storm for five days a couple of years back. As it stands now there is no space behind unless I loosen all the anchors and build out the furring another 1/4 inch to give new insulation space. Which also means I have to remove the entire wall not just the smaller section. If it would help I can foam in 7/8 of the pipes as they are now, and I do allow the water to drip on below 10 degree days. I just wondered if the blocking around the pipes might trap the air and make things more amenable to freezing when contrasted to no blocking in the space before work to support cabinets.

Re: Same project different area as earlier

#4

Re: Same project different area as earlier

don stephan

You cut holes in the wall at the floor and ceiling and cover with HVAC grills, to facilitate room air circulating up the wall around the pipes.

Re: Same project different area as earlier

#5

Re: Same project different area as earlier

Barry Irby

Don has a good Idea here, IF there is a open passage from grill to grill to allow air flow.

I think it would be a good idea to replace any metal pipe straps with plastic ones to avoid conducting the warmth out of the pipes into the wall.

Your idea of "caulking" the back side of the pipe with foam seems like a good idea and I don't think it could hurt. Leave the room side "open" to absorb room heat.

ANY separation between the pipe and wall woudl be good to avoid conduction.

And the drip thing on the coldest days woudl be good.

You could put a heat tape in with the pipes, but I seldom see them last very long and I just don't like mixing electricity and pipes and water. (Old Fuddy Duddy coming out here.)

Re: Same project different area as earlier

#6

PS....

Barry Irby

We used to leave a light bulb on in such areas to provide enough warmth to keep things above freezing. Not so much anymore. This last winter pipes were freezing every where. One of my tenants replaced the burned out bulb under his house with a CFL. Pipes froze.

Modern bulbs such as CFL's and LED's don't put out much heat. Every solution has it's problems.