Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Construction or gorilla or ?

Posts

Construction or gorilla or ?

#1

Construction or gorilla or ?

Gary Smyth

Awkward location. Not much leverage. Need to secure wood furring to house foundation (interior side) concrete block. I need to apply multiple layers to build up to final height in existing space.

Multiple house water lines are in the way so that I not only need to build out I need to build around and have the possibility of access at some unanticipated date.

Problem 1. Attaching furring to concrete block. Problem 2. Attaching wood to wood to achieve the correct height. Once at proper height surface treatment is to reattach some existing (no longer made) inexpensive 1/8" paneling. I have no desire to replace a total wall of the cheap stuff at this time, just get it back to look right.

I thought of using concrete nails in problem 1 but I have little room and do not want to risk breaking the block. No space for a drill. Lots of people do this I"m sure in many ways. By the way, the wall section (4'x6') once finished will have to support 60 lbs. permanently. Suggestions?

Re: Construction or gorilla or ?

#2

Re: Construction or gorilla or ?

John McGaw

Is the wall in question subject to moisture? If it is relatively dry I'd go for adhesive over nails although if you have access to a powder-actuated nailer it might be worthwhile going that way for the speed. I've used Loctite PL Fast Grab adhesive to fasten furring strips to dry concrete blocks and it still seems to be holding well. The 60 pounds you quote is quite a light load so almost anything could be made to work in a pinch.

Re: Construction or gorilla or ?

#3

Wall is dry- now.  Hopefully forever.


Re: Construction or gorilla or ?

#4

Re: Construction or gorilla or ?

Barry Irby

I have boxes of hardened nails meant to be driven into block with an air nailer. Unfortunately, the nailer was stolen. And they are clipped head nails and any new nailer woudl use full head nails. (world's smallest violin playing in the back ground) Anybody want some free nails? Actually, you can hand drive them (Heaven forbid) too.

I think Loctite makes PL 500 for landscaping applications. Might be just the ticket for gluing wood to block that might be wet. I sued dozens of cases of PL400 when I was building to glue down subfloors. good stuff.

Re: Construction or gorilla or ?

#5

Re: Construction or gorilla or ?

Bill Tindall, E.Tn.

Can you use Tapcons? Vastly superior to nails

Re: Construction or gorilla or ?

#6

Checked with fastenal

Gary Smyth

Checking to find if I can fit a right angle drill or maybe sockets. Doesn't look good what with screw length, socket, and wrench, and angle placement

Re: Construction or gorilla or ?

#7

Re: Construction or gorilla or ?

Terry in Edmonton

I have used PL400 for this and to hold carpet nailing strips to the floor. The strip I had to remove took a hammer and chisel to get off the floor, the remaining glue took a wire wheel on an angle grinder to get off. You will find it to be very moisture resistant as well.

Re: Construction or gorilla or ?

#8

I've not had much luck with construction adhesive

John in NM

But then I'm a bit wary of poly glues too, so I'm not sure I can help you at all. More often than not, I've found that the "liquid nails" type of adhesive fails within a year. I've not had gorilla glue fail, though I've rarely used it so that may not be saying much. The failures of construction adhesives I've seen could well be due to poor (or absent) surface prep rather than a deficiency in the adhesive itself.

I've not tried the stuff Barry suggests, but that would be something to look at. I've also used 100% silicone caulking on non-structural applications. Seems like that stuff sticks to everything and is rubbery enough to cope with extreme wood movement (and that's also why its non-structural :D )

Re: Construction or gorilla or ?

#9

Re: I've not had much luck with construction adhes

Barry Irby

John says he has not had much luck. I have had both good luck and bad.

When I was a builder, I used a huge amount of PL 400. Back in the day it was BF Goodrich PL400. I don't know when it became a Loctite product, but hopefully they have not downgraded the formula. Used it by the mile to glue subfloor to joists under every possible weather situation. Glued stuff to joists that had frost on them and to lumber so hot in the sun we had to keep moving to avoid the glue drying out. Never had a complaint about PL400. Except one. We glued slate flooring in a foyer to plywood. About ten years later the second owner decided to remove it. He tried everything. Broke pieces trying to pry it up with a hammer and chisel. Got stoned on the fumes of lacquer thinner and acetone. Ice. Bigger hammer. Torch. Gave up and tore out the plywood. Set it out in the woods and the plywood rotted off the back of the slate.

OTOH, the supply house sent me some brand X junk and my guys used it to glue down the subfloor in my kitchen. "Glue" in this case was sort a stretch of the imagination. Cooks get to eat their mistakes and builders get to live in them. 35 years later, I am still living with that mistake. I have torn out part of the kitchen but not all of it. Someday....

PL400 was good stuff....

Re: Construction or gorilla or ?

#10

Re: Construction or gorilla or ?

Walt

I was thinking Tapcons too. Use them with adhesive - I've had good luck with PL as well . It sounds like Gary's work space is sorta confined. I've had the best luck drilling holes for Tapcons with a hammer drill but there may not be room for that.

Re: Construction or gorilla or ?

#11

Good info...

John in NM

Next time I need something of this type, I will give the PL-400 a try, thanks! Problems I had were all with Liquid Nails products.

Re: Construction or gorilla or ?

#12

Jason Roehl in Lafayette, IN

I just LOVE that stuff!

Jason Roehl in Lafayette, IN

Especially when the "framers" in a log home slop it all over the show side of the logs or exposed joists. Can you say, "major pain in the kiester to remove"?

Jason