Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Is 1/2 hp Grizzly Benchtop Mortiser worth having?

Posts

Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#1

Is 1/2 hp Grizzly Benchtop Mortiser worth having?

Barry Irby

A friend has a Grizzly 1/2 hp benchtop mortiser he got at an auction. I can get it for very little. Is it worth having at any price? I use a drill press attachment now and find it inconvenient to switch the set up back and forth from DP to mortising.

I could get this machine and leave the DP set up as a DP.

I need to check and see if my existing Delta Chisles will work in this machine.

This one has about a four inch stroke and no bells or whistles. No tilt or cross slide vice, but neither does the DP. It is dated 1995.

Should I get it or let it go?

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#2

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth havi

mdclor

Barry, I have a Jet version and found the hold down to be a POS IMO. I now use a router to cut mortises because it is faster and more accurate for me. I do think it would be a step up from the DP however.

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#3

If the price is right.... yes

John in NM

I had a similar version from Jet for several years. They aren't great compared to a heavy mortiser, but the do beat a drill press, and you don't have to set it up every time.

Worst part for me was my hand would get tired holding pieces against the fence - but then I would be doing it for 2 hours at a time.

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#4

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth havi

Dave Bair

Yes, if for no other reason than it's a lot easier to pull that long lever than to crank that short-handled wheel.

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#5

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth havi

TomD

If the price is really low, go for it. I don't like that series, I think they are two light, look at the recent thread for the mortising machines where Bill bought a tank at the end of the day. BUT, the grizz table top always got good reviews; it will work a lot better than your drill press set up, and leave it to do what it is good at, as you say; And it does stuf the industrial machines mostly won't, like cut angled mortises for dining chairs, so even if you move to a larger shop and buy a massive machine, you may still want to keep this one.

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#6

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth havi

Walt

If you do get it, keep your eye out for a cross slide vise. There are directions around on how to modify one to work with a bench top mortiser, you need both screws to come out the same end. That really helps with the crappy hold-down problem.

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#7

It came home with me....

Barry Irby

My friend bought it in combination with a "ham radio" at an auction. It was listed as a drill press. He wanted the radio. He buys "stuff" at estate auctions and freight auctions and resells it. Turns out both pieces were labeled wrong. I told him this was a mortiser and he discovered the other thing was a signal generator for repairing radios. so much for online auctions where you don't get to personally inspect the stuff.

He took $30 for the mortiser. Appears to be in nearly new condition. In fact the only indication it has ever been used is some pencil lines on the bed that probably incited the length of the few mortises it ever cut. Whatever chisels the guy had were lost in transition. Sorry about that. They appear to be about $30+ a set so each will cost me more than I paid for the machine. I am still pretty sure this is a score. Going now to check my Delta chisels and see if they will fit.

Re: Is 1/2 hp Grizzly Benchtop Mortiser worth having?

#8

Re: It came home with me....

William Duffield

You'll like it a lot better than the DP kit, but not as much as a Powermatic floor mount. If you are planning to get a Festool Domino soon, you don't need it at all, and you could probably do without the Powermatic. IMHO, a cross slide vise is essential for one of these or for the DP kit, because the holddown fork just doesn't work. The necessary modification is easy. It consists of drilling and tapping one screw hole for a garter, and reassembling. Check Grizzly and Enco for the vise.