Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Saw blade sandpaper question

Posts

Saw blade sandpaper question

#1

Saw blade sandpaper question

Barry Irby

Was watching a wood working show and they had lined the inner side of their miter gauge with sand paper to help prevent the work piece from sliding. What bothered me was they were cutting through the sandpaper with a WoodWorker II tablesaw blade. Does not seem like a good idea to me. Do you think it would dull the blade?

Re: Saw blade sandpaper question

#2

Re: Saw blade sandpaper question

Bill Howatt

I am an advocate of lining the surface with sandpaper trick. I doubt if cutting through my little strip of sandpaper is likely to do much to dull the blade. Every cut you make dulls the blade a little.

I've had the same sandpaper strip on the gauge for years so it certainly isn't repetitive cutting.

Bill

Re: Saw blade sandpaper question

#3

Re: Saw blade sandpaper question

Ralph Lipeles

Rather then using a single piece of sandpaper you could do it with 2 pieces, each spaced 1/32" right and left of the cut area.

Ralph Lipeles

Re: Saw blade sandpaper question

#4

Re: Saw blade sandpaper question

William Duffield

Yes, it noticeably dulls the blade. Don't do it. DAMHIKT.

Re: Saw blade sandpaper question

#5

Duh!

Bill Tindall, E.Tn.

Was this a UTube video sponsored by a sharpening company?

Re: Saw blade sandpaper question

#6

Am I Misunderstanding this setup?

Bill Howatt

I assumed the sandpaper was attached to the face of the miter gauge the wood rests against so it wouldn't slide. Why does the blade have to touch the sandpaper at all?

In my "I cut it once" post above, I was referring to a longer fence I permanently screw onto the gauge and then put sandpaper on it. I then run it through the blade with my long fence to trim it to size - the end of it is the edge of the blade and it makes a handy reference. I could leave the sandpaper off before I trim it and then set it back from the edge.

So what am I not getting?

Bill

Re: Saw blade sandpaper question

#7

Re: Am I Misunderstanding this setup?

Barry Irby

This was from the WoodSmith Shop They were using a miter gauge with a wooden fence attached and a strip of sandpaper on it. They cut right through the sand paper. It appeared to be stearated Aluminum Oxide PSA paper. If I understood what I was seeing, they cut through it with a regular blade and with a dado set. Like you, I have used sandpaper on the fence and it work well, but I cut the fence first and then install the paper and never saw through it.

Re: Saw blade sandpaper question

#8

Just one cut?

John in NM

I doubt I would do it, but I also don't think a single cut is going to dull the blade significantly. Seems kinda a silly thing to make a habit of doing however.

On the rare occasion that I've done something like this, I've found it easy enough to cut the sandpaper with a utility knife and then apply it where needed.

Re: Saw blade sandpaper question

#9

Use old blade?

Doug Wolf

Am I the only one that has an extra blade or two that I use to cut old dirty lumber?

Just put it on the saw, cut the fence with sandpaper attached, then put your "good" blade back on the saw.

Don't tell my wife I have extra blades, I've been telling her I need more. ;)

Re: Saw blade sandpaper question

#10

Re: Saw blade sandpaper question

Jesse Cloud

I wouldn't worry about it. One cut through some sandpaper is nothing compared to routine cutting through the hardened glue in MDF and plywood - and most of us never give that a second thought.

Reading between the lines, it kinda sounds like some folks may be uncomfortable with getting blades sharpened. Shouldn't be. If you don't have a connection to a good sharpener, ask a local cabinet shop or similar trade where they get their blades sharpened. That place will probably welcome walk-in trade. They will do a good job and not charge an arm or a leg. ;)

Re: Saw blade sandpaper question

#11

Re: Saw blade sandpaper question

Joseph Mulherin, sr

Go to HF and buy their blade sharpener machine. I had one before my shop robbery and it did just fine. Did 7 blades in all and still have the first on on the table saw and the second is attached to the saw for replacement when needed.