Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Steve Latta auxillary bench

Posts

Steve Latta auxillary bench

#1

Steve Latta auxillary bench

Bill Tindall, E.Tn.

Quartered Wormy Oak Steve Latta Auxiliary Bench

PIC 1


I made the bench in what seemed to me to be the most reasonable way to make it. The legs are dovetailed into the sides and the stretchers are M&T into the legs. I don't understand the I-beam construction Latta advocates. I may add an "apron" across the front to provide a clamping surface. If so I will just screw it on so I can remove it if it gets in the way of my preferred F-style camping of stuff to the surface.

The joinery came up snug. The joints are not glued and won't need to be unless something shrinks and loosens. In this state I can disassemble and alter leg length if needed (see below M&T detail).

I wish I had not used oak. It is miserable to work with hand tools. While it saws fine, I had no problem sawing dovetails, it does not scribe mark and chisel fine. If someone decides to build a bench I would recommend maple. The first socket was too tight and paring to get a good fit was difficult with oak. By the time I sawed the 3rd I was able to judge where to saw relative to the scribe line and the last two joints fit without modification.

I sawed the tails with a Lee Valley saw, 12 point rip. This saw was way too aggressive for oak. The teeth were so grabby that my several hundred pound bench shook while sawing. I used the vintage saw shown (filed by Tom Law cross cut) for socket sawing and it did well. The LN dovetail saw was too dainty for this job.

PIC 2



The picture shows how I positioned the legs perpendicular to the top for dovetail socket marking. Anyone got a better idea? This worked but it seems a bit strange.

PIC 3


Oak pares poorly and I could not chisel the bottom of the sockets smooth. The router plane came to the rescue.

The stretchers are M&T into the legs. The tenon is half the thickness of the stretcher and it is not centered but rather it is at the top surface of the stretcher. If I want to shorten the bench I will just turn the stretcher upside down and reinstall. An inch of leg with stick below the stretcher in this position and can be cut off.

Vise to be added later.

Re: Steve Latta auxillary bench

#3

Re: Steve Latta auxillary bench

Jesse Cloud

Those dovetails look pretty darned "flauntable" to me!

Re: Steve Latta auxillary bench

#5

Re: Steve Latta auxillary bench

Joe in a Cleveland suburb

Nice work. This should be an article.

Re: Steve Latta auxillary bench

#6

Re: Steve Latta auxillary bench

Keith Newton

Bill, Im not familiar with this type of bench. What is it's intended purpose, and why are the legs set in from the ends so far.

Looks like if someone tried to use it as a carpenter's bench to stand on for installing crown in 8' high ceiling, one step near the end would flip the other end up.

Re: Steve Latta auxillary bench

#7

Re: Steve Latta auxillary bench

William Duffield, on the Cohansey

Check out the comments and links on the equivalent thread on the Hand Tool Forum, where its functions are much more clearly explained.

Re: Steve Latta auxillary bench

#8

I agree   


Re: Steve Latta auxillary bench

#9

Re: Steve Latta auxillary bench

William Duffield, on the Cohansey

Note that Bill posted this new thread on construction progress on both boards. He previously posted other threads asking for design advise on both fora. You'll find more pertinent information in those threads. If you need further illustrations of historical examples, you'll need to wait at least a couple days until I can get home to my iMac. I don't have the pertinent photos readily available on my tablet. My flight yesterday was cancelled due to ice in Phily, and tomorrow's forecast isn't very promising either.

Re: Steve Latta auxillary bench

#10

My use

Bill Tindall, E.Tn.


I will be using it to do Line and Berry inlay, a feature of Chester County, PA furniture style around 1700.


On a lower bench it is hard on the back.

Re: Steve Latta auxillary bench

#11

Re: My use

Barry Irby

It seems to me...(as he sticks his nose in on something he knows nothing about)....the height should be about and inch or two below the level of your forearm when your upper arm is near vertical and the forearm is level/parallel to the bench. You want to be able to stand up straight, bend your are at the elbow and work. Maybe that's too high. I seems to me you want to put a little "shoulder" into it every now and then. You don't want to have to bunch up your shoulders.

Now that you have made one, you can play (oops, work) with it and see how it feels. I think it should be anchored near the front edge of the bench so you don't have to bend forward to reach it.

OTOH, I have never done a line or a berry so who am I to say?

Re: Steve Latta auxillary bench

#12

Re: Steve Latta auxillary bench

Keith Newton

I guess I see now. That should put the work in pretty close range so you could wear a magnifying visor too. That is what I like to do when I'm doing the fine details.

Barry, the shoulder lean can be replaced with light taps from a mallet.

Re: Steve Latta auxillary bench

#13

Re: My use

William Duffield

There is no perfect height, but we are lucky we are flexible. What might be a perfect height for one tool is either shorter or longer than optimum for another. I use mine for work other than stringing as well, so I'm often using it with different tools. For exmple, if you use it for carving, especially with a mallet, you will want to make it a little lower because you are holding the chisel farther above the work than if you are using stringing tools or flush cutting berries with a paring chisel.

If you use it for sawing dovetails, or for marking pins from tails, you will want to clamp it so the front edge is even with the front edge of your bench. This gives you an uninterrupted vertical surface you can clamp your work to.

Definitely experiment before you commit to certain height, but remember it is easier to cut legs shorter than to make them longer.