Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Latta auxillary bench question

Posts

Latta auxillary bench question

#1

Latta auxillary bench question

Bill Tindall, E.Tn.

Steve uses a "riser" bench for his line and berry work. My back is telling me what a good idea this would be. I'm not fond of spending time on "shop furniture" so I only want to make one, and make it right the first time. I only have a poor picture of Steve's bench. Does anyone have suggestions for making this bench?

I am thinking it should be as long as a drawer. Width? Maybe as wide as a drawer? About sternum height from the floor? Other than dog holes and a cheap vise anything else on it?

Re: Latta auxillary bench question

#2

Re: Latta auxillary bench question

Neal in San Jose

Once you make one, you will wonder how you got along without it. Mine measures 9 1/2 wide by 42 long by 11 3/4 high. Why? I had a nice piece of 1 5/8 maple that was looking for something to do! I intentionally made it taller than I will eventually want it, but I haven't cut it down yet. I'm thinking it is about an inch too high. Make sure yours is high enough to accommodate your hold fasts. I also added a 1 5/8 thick by 2 1/2 apron between the front legs.

What did I do right? I didn't drill dog holes first; just drill 'em as I need 'em. The width seems about right. The apron on the front with dog holes is very handy.

What would I change? It's too long. That makes it heavy and awkward to take on and off and store. I'll shorten it eventually, but it's pretty far down the To Do list. I'd offset the legs front to rear. I drilled dog holes in the legs, but the holdfast hits the rear leg. I drilled oversized holes in the rear legs to accommodate the hold fasts - still a problem, but it mostly works. Add some way to secure it to the main bench. Currently using "F" clamps using a dog hole right at the bottom of the legs, but I'm not entirely happy with that as the clamp sometimes interferes with a wide or long piece clamped to the front. I installed a Lee Valley "Prairie dog" in front of the vice. I never use it.

Re: Latta auxillary bench question

#3

Re: Latta auxillary bench question

TomD

There is a lot of stuff out there, try a search for joinery bench, which can be separate or on top of the regular bench. That may not be exactly the thing you want, but a lot of the issues are similar. I remember one Williamsburg conference where every second picture had one in it.

Re: Latta auxillary bench question

#4

That's what I was looking for

Bill Tindall, E.Tn.

I was considering an apron. I am a great fan of F-clamps and thought the apron would provide a place to clamp to as needed. I am less a fan of hold fasts so designing to use them is less important to me. I like your suggestion of drilling dog holes as needed.

I intend to dovetail the legs to the top and M&T or dovetail a stretcher front to back between legs. I don't strive for flauntable dovetails so for me dovetailing will be quick way to make a sturdy leg attachment.

I was planning 42". I'll put a big overhang on the end that I can cut off if the length and weight is annoying.

Overall a big thanks to benefit from the results of your experience.

Re: Latta auxillary bench question

#5

Re: Latta auxillary bench question

William Duffield, on the Cohansey

I just cut a couple inches off the bottom of my holdfasts when I discovered they were too long for my ~9" wide bench top.

Re: Latta auxillary bench question

#6

Re: Latta auxillary bench question

Jesse Cloud

The best design depends, of course, on how you will use it. I use mine mostly for inlay and detail work, so I sized it so that I can comfortably get real close. If you plan to work with large pieces, e.g. table legs, be sure to make it heavy enough that the piece won't try to tip things over.

On the other hand, its also a good idea to provide for clamping the bench down. I fashioned clamping holes in the legs of my bench.

Finally, be mindful of the size and weight of the thing. Too big makes it hard to lift and awkward to store. Everything is a compromise.

Maybe the most important decision is whether you are building a tool or furniture. I know some folk have built theirs with fancy joinery and fine finishes. Mine was built so that I would mind gouges and dents.

Re: Latta auxillary bench question

#7

Thank you ....question

Bill Tindall, E.Tn.

Helpful.

Will be using it to do Line and Berry inlay on doors and drawers. I am 5'7". I am thinking about 44 total inches off floor -bench plus auxiliary bench.?. The lumber works out 11" wide edge glued. I am thinking I should make it more narrow?

"Mine was built so that I would mind gouges and dents. " Ditto! I doubt the dovetails will look flauntable either.

I have the lumber picked out. It will be made from 7/4, quartered oak (that is shot full of worm holes and bowed 4" across its 10' length). The quartered oak is elegant- the 7/4, bow and worm holes makes it useless. From a distance it may look like a showpiece. :)

Re: Latta auxillary bench question

#8

Re: Divide and Conquer :^)

William Duffield, on the Cohansey

We now have discussions going on this subject on two WoodCentral forums. It would be wise if those of you who might be interested in designing and building one of these would try to follow both discussions.

Re: Latta auxillary bench question

#9

Indeed.....

Bill Tindall, E.Tn.

Don't miss the "Swiss Cheese" version posted on the hand tool forum:)

Re: Latta auxillary bench question

#10

Re: Thank you ....question

Jesse Cloud

I suggest making a prototype from plywood or some scrap to zero in on the best height. Just try it to see if it feels comfortable and if you can handle your work easily at that height.

Since inlay work does not require much physical force, but takes a long time, at least for me, I do most of it sitting on a stool by the bench. So I only need a few extra inches of height (six to be exact). I don't use holdfasts. The bench on a bench is about 7 by 14, and I'm usually working off the 7 inch dimension.

Don't know if this applies to you, but I chose to make the aux bench the same height as my moxon vise - which often comes in handy.

Re: Latta auxillary bench question

#11

Re: Thank you ....question

William Duffield, on the Cohansey

I agree, doing inlay and stringing doesn't put a lot of strain on a bench, but once woodworkers have figured out that these thngs reduce their back pain and increase the precision of their work, they start to use them for all sorts of other work. For example, Mary May and the cabinetmakers in the Hay shop at Colonial Williamsburg use them for carving, sometimes with a mallet, and sometimes by hand. Some people use them for laying out and sawing dovetails. In that light, some, myself included, attach a Moxon vise to the front of the bench. An advantage is that you don't need a separate Moxon vise, and you don't even need a purpose built rear jaw. It is also at a very convenient height for making moldings and trimming edge banding with a power router. Some of us use them in our shops but also take them on the road, for demonstrations in remote locations. If you need to clamp it to a picnic table or an F150 tailgate, or wheel it over a parking lot and a convention center floor, it needs to be a bit sturdier. In addition to all the uses I've mentioned above, I use mine all the time with holdfasts, which can put a lot of strain on the dog holes, the joints between the top and the legs and the ports used to clamp it to the substrate. When I'm working in my shop, mine is almost always attached to the top of my bench, so I don't have a need to find a permanent place to store it.

Re: Latta auxillary bench question

#12

Re: Thank you ....question

William Duffield, on the Cohansey

Everyone's shop practice is different. I almost never sit in my shop; only when I need to rest because my back hurts. I have too many tools and materials I use, and too many different operations I'm trying to perform to take the extra time to stand up and sit down, or move a stool around. Building a prototype is useful, or you can intentionally build it a little too high, and cut the bottoms off the legs until you get it just right.