Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Worked on my clock a little

Posts

Worked on my clock a little

#1

Worked on my clock a little

Joe in a Cleveland suburb

I was able to work on the doors to my clock this weekend. I used scrap pine to test and practice making the, I guess it's called, bridle joints with offset shoulders. I did a bridle joint because I think it was easier than a regular mortise and tenon and I don't have a mortising chisel that would have been small enough. Didn't want to buy or making one either.

The doors turned out ok, but the cuts,joints, grooves, shoulders and so on aren't as crisp and clean as I would like.

Made sure things were square (doesn't seem to actually help - nothing ever seems to end up square). I double check sometimes with a square.


Squared up rails and stiles (or at least tried to)



Cut Dado's


Marked out shoulder cuts


Cut the tenons. You would think with a Freud SD508 I'd be able to get nice cuts. Never.


Cleaned things up a bit



Cut mortise


Stuck the rails and stiles together temporarily - looks like it might work


No. That's not the real clock dial...

Thanks for looking - if you see something wrong, tell me.

:)

Re: Worked on my clock a little

#2

Re: Worked on my clock a little

Lars Parrington

looking good.

is that some a fingerboard in the "cut dados" photo? If so it looks unusual. How is it designed, and does it work well?

Re: Worked on my clock a little

#3

Re: Worked on my clock a little

Chuck in Mtl.

wow is all i can say. Nice looking clock design and i really like the figured grain of the wood. To me that will make the big difference in the finished item. Lack of squareness in the cuts seems to be the bane of all woodworkers. Its a fact of life it seems. only Norm Abrams can get the cuts square, or so it seems, but he spends hours setting up the cuts.

Re: Worked on my clock a little

#4

Re: Worked on my clock a little

Hank Knight

Lookin' good, Joe. I kinda like the clock face, and your maple is stunning. It's going to be a great looking clock.

Re: Worked on my clock a little

#5

comments

Bill Tindall, E.Tn.

I am liking the looks of it.

1. are you sawing your shoulders or chiseling to a scribe line. I never had success sawing. When I saw the Headley shop also chiseling I concluded that sawing shoulders was never going to be reliably accurate and abandoned trying.

2. Nothing beats a shooting board for squaring an end. Again I find sawing works only most of the time.

Re: Worked on my clock a little

#6

Re: Worked on my clock a little

Joe in a Cleveland suburb

Hi Lars.

It's just a simple (I guess it's called) spring board(?) - not even sure what it's called. I probably saw its idea in a magazine some time ago. Just a scrap piece of wood with a few kerfs. I just screw or clamp it to a fence. It puts a little pressure down on the piece with a little bit of 'springy' give to it. Nothing fancy. Works well.



Joe

Re: Worked on my clock a little

#7

Re: comments

Joe in a Cleveland suburb

"I am liking the looks of it."

Thanks. The next one will be Cherry though.

"1. are you sawing your shoulders or chiseling to a scribe line. I never had success sawing. When I saw the Headley shop also chiseling I concluded that sawing shoulders was never going to be reliably accurate and abandoned trying."

I used the table saw and dado blades. Using scrap I messed around with, or practiced with, using hand tools to do the tenon and mortise. Wasn't too happy with the results, and I don't have much spare curly maple, so I went with the table saw. Using the dado set for the tenons and my TS tenoning jig to cut the mortise for the bridle joint - hope that makes sense. That was on the top door. For the bottom door, I cut the cheeks with a cross cut blade, then the tenoning jig for everything else.

Most of my problem with getting square had to do with cleaning the milling marks off the rails and stiles. My (crappy Delta) jointer, even with fresh knives, was giving me too much tear-out. With my hand planes, I get zero tear out. But I'm not skilled enough to plane the long grain edges square to the face of the rail/stile. I got a lot better at it (by realizing/remembering) to tap the iron over a tad towards the high side. It worked out ok.

The other problem is my rip blade does not produce a perfectly flat kerf - not sure how to explain it in words, maybe I should take a picture of it. So the bridle joint doesn't end up perfect.

"2. Nothing beats a shooting board for squaring an end. Again I find sawing works only most of the time."

After my questions last week in the Hand Tools forum, I cleaned up my shooting board, made some adjustments, and it's working pretty well now. Square clean ends of a stick aren't much of a problem now.

Thanks.

Re: Worked on my clock a little

#8

Re: Worked on my clock a little

Lars Parrington

Cool. Thanks for the photos Joe. Looks like an interesting and potentially useful widget. Like a fingerboard that doesn't restrict travel in one direction.

Re: Worked on my clock a little

#9

Re: Worked on my clock a little

David Churnega

Nice work.

Building one of these is on my bucket list. A few questions.

1. What is the spring board for? Does it have something to do with the movement?

2. Are you using a mechanical movement and if so, which one and where did you get it?

3. Dial face, did you buy one and where?

I have been studying Shaker items for some time. The scan shown here is from "The Book of Shaker Furniture" - John Kassay. This is the definitive book of dimensioned drawings.


img

Re: Worked on my clock a little

#10

Re: Worked on my clock a little

Joe in a Cleveland suburb

Thank you David.

1. What is the spring board for? Does it have something to do with the movement?

i'm not sure what you are referring to.

2. Are you using a mechanical movement and if so, which one and where did you get it?

No. Not mechanical. Too expensive for me.

3. Dial face, did you buy one and where?

I bought the face and movement from http://www.merritts.com . I bought 3 different sizes from them because I could not get a straight answer from them when I called as to the actual size. As I recall, they are only about $1.50 each so I bought a couple of each size. I plan to make a second clock sometime out of Cherry.

I have that Kassay book. I use it for reference but I am not attempting to build a correct reproduction. I am also using an article from FWW by C. Becksvoort as reference and ideas.

Let me know if you have any other questions, I'll try to answer them.

Joe