Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Advice needed to make/match a hole

Posts

Advice needed to make/match a hole

#1

Advice needed to make/match a hole

Gary

I am in the process of making a sewing machine cabinet for my better half. I'm really struggling with the recall part of my grey matter: I am at the point of cutting the hole for the sewing machine in the cabinet top, to place on the machine lift. The goal here is to have an opening cut out for the machine, and a filler piece of wood on the lift which matches the hole, so that when the machine is in the uppermost position, the filler completely fills the opening. I also need to (rabbit?) in a filler piece so that when the machine is in the middle position this piece fills the difference between the opening and the smaller space the machine takes in that position. Not sure if that makes sense to you reading it (can't read my mind, can you....).

What is the best way to accomplish this? Should I use a jig saw to make the rough opening, then route the final shape? I suppose that would be possible with an edge to rout against on the sides. How then would I make the filler piece the right shape/size? I really can't remember the steps here. Advise would be SO appreciated.

Thank you.

Re: Advice needed to make/match a hole

#2

Re: Advice needed to make/match a hole

Lars Parrington

Are you planning to reuse the piece you cut out to make the hole as the filler piece for said hole? In that case you'd have to compensate for the material removed by the kerf. Perhaps by adding some banding around the cut out piece, or by cutting it out with your saw at an angle.

As for how to cut it out, it would help to know if the cabinet top can be treated as a board (and thus run through stationery machinery), or if it is already permanently afixed to some kind of base.

a picture might really help here.

Re: Advice needed to make/match a hole

#3

Re: Advice needed to make/match a hole

Yonak

When I have a closed hole to cut I use a sabre saw and spindle sander. (Remember, you would have to shape the routing guide so you might as well just shape the hole itself.) For the insert I would use a band saw, spindle & disk sanders and then cut the rabbet.

Re: Advice needed to make/match a hole

#4

Re: Advice needed to make/match a hole

Gary Kittleson

Ah yes...a photo - worth a thousand words! As you can (now) see, the top is already attached. I was thinking of making a template (similar to the one shown - which of course isn't the right size...). Could I then use the template to smooth the opening, and also to make the insert? I'm thinking of guide bushings here. But, I've no idea how to figure out which guide bushings I'd use to get the proper spacing...

You can see in the photo the attachment for the lift. The wood insert is attached there, and in turn, the sewing machine. This needs to fit the hole made for it quite well, so there isn't an awkward opening.






Re: Advice needed to make/match a hole

#5

Re: Advice needed to make/match a hole

Lars Parrington

ahh... now i see.

No point in trying to reuse the cut-out piece then.

I think what I would do is make a template just like the one you have shown, except from thinner material (no more than 1/2"). Then rough out the hole with a jigsaw and clean it up by routing to your template. Rather than guide bushings, I'd use a flush trim bit with a bearing. One of the bits where the bearing resides on the shank of the bit rather than at the end. This way you can make the template the exact size you want the hole to be.

For the filler piece, I would just use the template to mark a line on the piece, and then saw and sand (or hand plane if it is solid wood) to the line.

Watch out for tear-out when jigsawing across the grain. Stay well back from the line or cut through the veneer with a knife first.

Looks like a nice piece of furniture already. Out of curiousity what are those cutouts in the edge of the top? Looks like they could be recesses for hinges or something.

Re: Advice needed to make/match a hole

#6

Re: Advice needed to make/match a hole

John Lucas

When I did it for my wife I sawed close to the line with a jigsaw to get the cutout. Then used double stick tape to fasten a template to the top and used a flush cut router bit to cut the opening. Used this same pattern with a smaller bit and larger bushing to route most of the way through some larger plywood for the insert. Then used the jig saw cut out close to that line to break it free and a flush trim bit in the router table to clean up the rest.

Re: Advice needed to make/match a hole

#7

Re: Advice needed to make/match a hole

Gary Kittleson

Looks like a nice piece of furniture already. Out of curiousity what are those cutouts in the edge of the top? Looks like they could be recesses for hinges or something.

Yes, they are flip-up/down extensions for the table - this is the Rockler plan...mostly, anyway.

Used this same pattern with a smaller bit and larger bushing to route most of the way through some larger plywood for the insert.

This is what I had in mind initially - I'm not really putting together the bit/bushing size thing in my head though...

Re: Advice needed to make/match a hole

#8

Re: Advice needed to make/match a hole

TomD

I think what might be being suggested is that if you use your template (female one) to cut out the hole, using a zero clearance bearing set-up (1/2" bearing, and bit, say), you will end up with a waste piece that is exactly 1/2" inch smaller all around, since that is the kerf of the bit. Now if you take the waste piece that is 1/2" smaller, and use is at a male pattern, and fix it to your piece you want to fit into the hole, and trim it with a bit that has a 1.5" diameter bearing, or collet, you will have an insert piece that is 1/2" larger than the pattern piece/waste piece was, all around, and actually fits all too perfectly in the hole. I don't own the bearings, or collets, though I see them for sale.

When you do the initial rout with the trim bit, go clockwise, particularly if you need the inside piece for the pattern. If you have a bit where the bearing is mounted on the shank, you can trim from above, and this wil greatly reduce the chance of blowing out grain on the topsheet.

That said, I would probably use a standard trim bit and your template to blow out the hole. Then I would simply use the template to trace the piece you want to fill in, then I would cut it out on the bandsaw, and sand it on a disc sander, since it is a relatively easy matter to split a line on the disc sander. I would either do that, then run the marking gage around the piece taking off another 1/16 all around for clearance, and then trim that on the sander, or I would use a very tiny spacer when transferring the line initially, so that my clearance was established that way.

Re: Advice needed to make/match a hole

#9

Trimming inside of opening

Gary Kittleson

Thanks for the replies to my question regarding cutting the opening for the sewing machine. This is what I started with:


This is after the hole was cut (I made a template, scored the cut line with a knife to keep from blowing out the top - thanks for that suggestion - then cut it with a jig saw, and then a pattern bit to clean it up.


This next shot is with the machine in it's free-arm setup, but lowered to match the height of the cabinet top. My plan was to create a filler piece, and make a rabbit to set it into the top, to transition from the top to the machine.


However, SWMBO would rather have the actual machine's filler in place, as shown below:


While I'm ok with that (after all...I doubt I'll ever use it...), it creates a bit of a quandary for me...as I'm not sure how to trim out that ugly plywood, which will not be covered by a filler now. The only option I've thought of is to square out the hole larger than needed, and trim the inside with hardwood...doesn't seem too ideal to me. Any thoughts?

Re: Advice needed to make/match a hole

#10

Re: Trimming inside of opening

Barry Irby

Nice work.....I did one like that about 40 years ago for my Mother. Yours looks better.

Those plywood edges might be a job for veneer tape.

Re: Advice needed to make/match a hole

#11

Re: Trimming inside of opening

David Yoho

Why not use some veneer edge banding to cover that edge. It should be flexible enough for the corners. I like the PSA backed banding but there's always the hot glue backed too.

Re: Advice needed to make/match a hole

#12

Re: Trimming inside of opening

Gary Kittleson

Ok...I could go that route. It will be a first time for me with that - I'm sure there is plenty of information out there (I'll do some looking) on technique. As far as supply goes, is this a Box Store (Home Depot) thing, or an internet purchase for me? Wood to match is quarter-sawn red oak.

Re: Advice needed to make/match a hole

#13

Re: Trimming inside of opening

Barry Irby

Got a piece of Red oak? You could make your own.

I used to buy it rolled up in little plastic "cans" about the size of a hockey puck. Not sure about the big box stores but anyplace that sells to the cabinet industry should have it.

Re: Advice needed to make/match a hole

#14

Re: Trimming inside of opening

Lars Parrington

I'd probably end up making my own, just like Barry said. Use the tablesaw to rip some very thin strips off the edge of board. Soak them or steam them a bit to make them bend easier if necessary. Then glue them on with wood glue. Clamping might be tricky in the corners, but maybe tape could work as clamps.

Re: Advice needed to make/match a hole

#15

Re: Trimming inside of opening

Gary Kittleson

I'll give it a shot.

Thanks!

Re: Advice needed to make/match a hole

#16

Kneale Brownson

Re: Trimming inside of opening

Kneale Brownson

Something like a bungy cord might help hold the wood into the corners while the glue sets.

Re: Advice needed to make/match a hole

#17

Re: Trimming inside of opening *LINK*

Jesse Cloud

I would be wary of hardwood or veneer here. As you will be running a lot of fabric over that surface a small blemish or splinter can cause a disaster and a wife with an epic bad mood.

You might consider the T-shaped edge banding such as the link below.

It fits into a slot you cut with a router, easy to use.


T-shaped moulding

Re: Advice needed to make/match a hole

#18

Re: Trimming inside of opening

Barry Irby

I agree with Gary here. Even though I suggested the veneer tape, if you have rolled the edges of the hole AT ALL you will have trouble getting a perfect edge on your glue up. One splinter and some important delicate fabric might be ruined.

If I were to glue in veneer, I woudl find something like plastic pipe that exactly matched the curves in the corners or make something to use for cauls. Then I woudl line them with foam to improve even a perfect fit and to cause the tape to roll over the rounded edges. Trimming the edges of the tape is fairly easy, but delicate work.

I like the Rockler tape suggested above. I might even consider painting the edge of the plywood.

Re: Advice needed to make/match a hole

#19

Fill it/paint it

Bill Tindall, E.Tn.

I would fill it with water based grain filler, sand it smooth and either stain or paint it dark.

Re: Advice needed to make/match a hole

#20

Re: Trimming inside of opening

George Boat

For the sewing machine lift I made ( both of them) I simply rounded over the edges with router bit and then lots of sanding and many coats of varnish with sanding. No snags at all. The ply edge is not visible in use.