Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Any experience with Sharkbite Push on Connectors?

Posts

Any experience with Sharkbite Push on Connectors?

#1

Bart Goldberg

Any experience with Sharkbite Push on Connectors?

Bart Goldberg

I just spend 1/2 a day with my neighbor, troubleshooting a problem with my whole house humidifier. Turns out that the issues was with the saddle valve that the installed used to feed the humidifier. I would like to replace the saddle valve, and was considering using one of those push connect type valves with a T connector.

Anyone have experience with this? Or am I better off to call my local plumber and have him solder in a T Ball Valve?

Thanks

Bart

Re: Any experience with Sharkbite Push on Connectors?

#2

Re: Any experience with Sharkbite Push on Connecto

Paul Leuba

I'm just a regular old homeowner with no particular skill in plumbing Beyoncé replacing faucets, valves, washers,etc. I have successfully used the sharkbite fittings several times without aproblem. I found them particularly usefull in tight situations where there is not much room to solder copper or to use CPVC cement. I like them and would not hesitate to use them.

Paul

Re: Any experience with Sharkbite Push on Connectors?

#3

Re: Any experience with Sharkbite Push on Connecto

Bob Entwisle in NJ

I have used shark bit fittings on copper pipe a couple of times and would not hesitate to use them again. Best thing since sliced bread. They can make minor plumbing repair jobs take 5 minutes, instead of the usual 1/2 day.

Bob in NJ

Re: Any experience with Sharkbite Push on Connectors?

#4

Re: Any experience with Sharkbite Push on Connecto

David Yoho

I've used them a few times when soldering would have probably caught something close by on fire. I wouldn't hesitate to use them again.

Re: Any experience with Sharkbite Push on Connectors?

#5

Re: Any experience with Sharkbite Push on Connecto

Barry Irby

I have used the about a dozen times and on several different houses. Would not hesitate to use them again. the only failure I have seen was on one I saw during a home inspection. It had frozen, or at least the system had frozen, and the fitting had been ripped apart, as if you pulled the pipe back out of the fitting, pulling the guts out. (Don't get me wrong, the system would have failed somewhere with or without shark-bites.)

Caution: be sure to seat the pipe fully. Cut the pipe, put a mark on each end about a half inch back, with something like a Sharpie and then seat them into the fitting. If you have room and everything lines up nicely, its easy. Sometimes its the b word. Look at your situation. Is it going to be easy to spring the pipes apart far enough to get the fitting in? Etc, Etc.

Re: Any experience with Sharkbite Push on Connectors?

#6

Bart Goldberg

Re: Any experience with Sharkbite Push on Connecto

Bart Goldberg

Barry - after further investigation, not sure I can use the Sharp Bite fittings. The pipe I need to work with has a OD of 7/8" (its the main hot water pipe coming out of my hot water heater). I have only seen fitting for 1/2 and 3/4" pipes. I was going to use a slip tee and then add an angle stop value to control the water to the humidifier. Not sure this plan will work now.

Bart

Re: Any experience with Sharkbite Push on Connectors?

#7

Re: 7/8" OD = 3/4" copper pipe  *LINK*


http://www.gizmology.net/pipe.htm

Re: Any experience with Sharkbite Push on Connectors?

#8

Re: 7/8" OD = 3/4" copper pipe

Barry Irby

Bob is right. If its copper and its about 7/8" it a 3/4 copper pipe. You can buy 3/4" sharkbites. They have tee's that are 3/4 3/4 3/4 and tee's that are 3/4 3/4 and 1/2 on the side. Not sure they have the slip one in that configuration.

The only thing I don't like about these fittings is the price. That Tee might be $10 to $15 and you can buy the sweat version for about 15% of that. Useful only if you can sweat pipe and if you can get to it to do it without burning your house down. The sharkbites are ten times faster and safer.

Re: Any experience with Sharkbite Push on Connectors?

#9

Bart Goldberg

Re: 7/8" OD = 3/4" copper pipe

Bart Goldberg

Yeah - I just found this out. Thanks for the info.

Regards

Bart - who hasn't done much plumbing (yet)

Re: Any experience with Sharkbite Push on Connectors?

#10

Re: Any experience with Sharkbite Push on Connecto

Mark Nowicki

About two weeks ago one of my tenants went to Cuba over Christmas, and,( since they pay for heating) they thought they would save some money and turn off the heat ( during a Canadian winter with temps of minus 25 Celsius.


If it weren't for Sharkbite fittings I would still be there.


The longer fitting on the red pipe is called a slip coupling.

(Get some PEX tubing as well)

and get those as well http://www.lenoxtools.com/pages/tight-spaces-tubing-cutters.aspx

http://www.sharkbite.com/how-to/sharkbite-slip-coupling-copper-or-cpvc-repair/

Mark

Re: Any experience with Sharkbite Push on Connectors?

#11

Re: Any experience with Sharkbite Push on Connecto

waroland

Used then two years ago in motorhome and have had zero problems and we live in it full time

Re: Any experience with Sharkbite Push on Connectors?

#12

Re: Any experience with Sharkbite Push on Connecto

John McGaw

My 'experience' was to look at the price tag and then to look at the equivalent price tag on conventional fittings. Then I thought 'I've never had any problem sweating standard fittings and if it takes four times, so what, I'm not going anywhere'.