Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Wooden boat glue / need to join dried cedar planks

Posts

Wooden boat glue / need to join dried cedar planks

#1

Wooden boat glue / need to join dried cedar planks

Michael Furibondo

Hello everyone! I am restoring an old cedar plank boat and it has been sitting in a very dry environment for years. the cedar planks have shrunk exposing very thin gaps between them. I'm looking for the best way to seal the hull and am looking at resorcinol amongst other glues and epoxys.

i found a great article on this site from Bob Smalser:

http://www.woodcentral.com/cgi-bin/readarticle.pl?dir=smalser&file=articles_737.shtml

but i still have a few questions. My problem is i cannot clamp the planks together because the boat is already assembled. So, if i cant put pressure on the bond, will that defeat the purpose of using glue to bond them together and seal my hull?

feel free to check out all of my pictures of the boat here:

http://furibondo.smugmug.com/Ole-Lind-Boat-Restoration/

Thank you!


img

Re: Wooden boat glue / need to join dried cedar planks

#2

woodenboat forum


Re: Wooden boat glue / need to join dried cedar planks

#3

Re: Wooden boat glue / need to join dried cedar pl

Kevin French

Won't the planking swell when wet and correct the problem.

When I was a kid I remember helping my grandfather launched his boat one spring He told me not to worry about the water in it. 'As soon as the wood swells it will stop'.

Re: Wooden boat glue / need to join dried cedar planks

#4

Re: Wooden boat glue / need to join dried cedar pl

TomD

What are we looking at there, is that a floor, or the inside of your hull?

You really need to get very specific advise, I wouldn't just randomly ask on the net.

1) Is this a restoration? Not my areas of specialty, and you get into all kinds of functional issues combined with preservation issues.

2) you want to rebuild the boat for best possible life here on out, and don't care about how they used to do it.

Best cedar hull will be epoxy sheathed with glass. How you go about doing that is a very specific issue. The outside can be cleaned to bare wood, then you may need to use some technique to rout out the seams, then you squeegee in glue, sand and fair. Then as a final deal you sheath the hull.

Now the best new build way to do that is normally to sheath the inside, you have to stop one moisture from getting in from behind. The ribs will stabilize the inside, but you still have to control absorbtion of moisture, and with the latice work of stuff you have there, it will be hard to totally seal it. You need a very specific solution.

Just throwing glop into the cracks is probably not a good ideal. I would not use resorcinol on anything, really today, but in particular not a bunch of cracks (but then maybe there is som 1) reason for doing that, there isn't nay boat building reason for it. There would have been an old process, like white lead, or something, but I don't do that stuff.

Epoxy is your ultimate wood salvation, but you have to be able to get it on clean wood, and on all surfaces, and no penetrations. If you can't do it the right way, epoxy can make maters worse. Lots of runabouts have been epoxied to beautiful shape, and there is some free info out there. Try the Gougeon site:

http://epoxyworks.com/

http://www.westsystem.com/ss/assets/howto-pub2/Wooden%20Boat%20Restoration%20and%20Repair.pdf

Re: Wooden boat glue / need to join dried cedar planks

#5

Ellis Walentine

Not an expert on this, but, a couple things...

Ellis Walentine

I agree with Kevin that wooden boats and hot tubs leak until they have swollen enough to close the gaps. Glue would just get in the way and when the wood shrinks again, it will just break the joints.

Resorcinol glue requires tight clamping, as it doesn't fill gaps well. Epoxy will fill gaps but it isn't recommended for sun exposure unless you top coat it with paint or crosslinking varnish. Polyurethane glue claims waterproof qualities, but it isn't rated for full submersion, and it doesn't have a lot of strength as it is mostly air bubbles trapped in a matrix of cured glue.

In short, I'd go for soaking the wood and waiting for it to swell. We have some serious boatbuilding talent here, so you may get a better answer, but there's my two cents.

Ellis Walentine, Host

Re: Wooden boat glue / need to join dried cedar planks

#6

Re: UV

TomD

It is true that UV is a problem for some/most epoxies. You don't need a cross linked varnish, though that is regarded as the best option for a bright finish. I use Z Spar Captains Varnish, and it is great.

If this is a Mahogany runabout type deal, all to be finished bright, you either have a boathouse, live where there isn't much sun, or spend a lot of time varnishing. On old boats in the tropics, the varnishing was continuous.

Lignin also breaks down in UV so varnish over wood will only last so long. It all comes down to needing to keep a bright boat out of the weather. My first boat was a cedar strip canoe, I got it out of my system. Bright finishes on anything that is vaguely working (into which I would put anything you leave out of doors), are not practical in my world, and I live north. But I certainly don't mind looking at them.

Re: Wooden boat glue / need to join dried cedar planks

#7

Jesper, Denmark

Re: Wooden boat glue / need to join dried cedar pl

Jesper, Denmark

My reaction is split between "Nice old strip built runabout" and my old friend Swifty's likely reaction" I'll bring the gasoline if you have a match"

Take it down to bare wood, as it looks like you are doing, all of it. Prime paint it, caulk it with something old fashioned, like linseed oil putty. Not epoxy or silicone or anything newfangled, you need the putty to stay relatively soft. The paint it with marine paint.

Pop it in the water without the motor. It will leak some and over a week or so, some caulk will squeeze out. It will stop leaking. Leave it in the water all season.

As an alternate, fill it with water on land and let the boat swell that way. Advantage is that you can fill it to above the waterline.

You will have some stripes the first season, where the putty is squeezed out - live with it.

Re: Wooden boat glue / need to join dried cedar planks

#8

Re: Wooden boat glue / need to join dried cedar pl

TomD

I guess a simpler way to say it is you can have an all high tech epoxy runabout, even best of show type boat; or you can have an old fashioned original, possibly best of show type boat. Best to avoid mixing the two. I would not caulk it with epoxy then throw it in to see if it swells up, but you can absolutely use epoxy if you go with a modern restoration.

The fly in the ointment of either approach is that you need to get down to the wood, and in a latticework of small pieces like you have there, you are going to be hard put to get everything clean to the point where you can build as if it was new. And if you don't do that you are possibly going to end up doing a lot of work to a boat that will not stand up.

For me the only route is the modern restoration because you end up with higher performance than the original; as much beauty as you want to take on the restoration of; and you end up with the lowest maintenance type of boat there is.