Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Question about pre-cat lacquer

Posts

Question about pre-cat lacquer

#1

Question about pre-cat lacquer

AZ in Colorado Springs

For repairing a worn or scratched lacquer finish, I understand that by applying or polishing on a new coat of lacquer, the solvent in the new lacquer will soften the original finish and the new coat blends into the old.

Does this work with pre-cat lacquer as well, or does the catalyst lead to a different chemical composition that makes the lacquer "set" permanently?

Thanks

Andy

Re: Question about pre-cat lacquer

#2

Re: Question about pre-cat lacquer

del schisler

by applying or polishing on a new coat , you mean spraying ? i spray lot's of pre-cat lacquer all the time, if their is a small scratch and not down in enough that it has removed the stain ? you can get a small painter brush the size of a pencel so the end will be the size of the pencel lead, now dip brush in the lacquer and paint the line with lacquer , it should disapear or be better you may have to do this a couple times, now it the scratch has removed some stain that is different, you will have to look at this first and determined as to that, if some stain has been removed don't put lacquer on yet you can use the same brush for stain , let the stain dry over nite if used , that do the lacquer , good luck i do this all the time

Re: Question about pre-cat lacquer

#3

to answer the chemistry question....

Bill Tindall, E.Tn.

The finishes we use can be divided into two categories, curing and not curing.

Conventional lacquer and shellac are solutions of the finish molecules. When applied the solvent evaporates and that's it. Expose the dry finish to solvent and they redissolve.

Varnish, polyurethane, pre and post catalyzed lacquer cures after the solvent evaporates. The stuff in the can is a solution of polymer molecules. After the solvent evaporates these molecules cross-link to form a few gigantic molecules. An analogy might be as follows. The molecules in the uncured finish are very long like a plate of spaghetti. The curing (cross-linking) links the spaghetti strands together in one or more places so there are no longer individual spaghetti strands. Hence they can no longer be separated into individual strands by adding back a solvent.

We often call this process "drying" which confuses the situation. The solvent dries, the remaining stuff "cures" (cross-links) An important property of a cross-linked finish is that it is insoluble in everything. A strong solvent may soften the cured finish but nothing will redissolve it. Also, cross-linked films are tougher than non-cross linked films.

Consult the supplier of finish to see if a precat lacquer can be recoated many days after curing. The curing reaction goes on for some time so that recoating is not an issue when done within a day or so. The details of the formulation will determine if there is any problem recoating weeks after application of the first coat.

Re: Question about pre-cat lacquer

#4

Re: to answer the chemistry question....

AZ in Colorado Springs

Thanks, Bill. That's the kind of thing I was thinking (but freshman chemistry whipped me and I never went any further in the sciences so I could never explain it so fully).

But, this leads me to a different question. A catalyst, as I understand it, doesn't really "participate" (that's not the right term, but hopefully you get my point) in the chemical reaction, but enables the chemical reaction to proceed more quickly/efficiently (as nitrous oxide enhances combustion in an automotive engine, for example).

So are "pre-cat" and "post-cat" really misnomers or incomplete descriptions of the modification to the lacquer? It seems to me that if a catalyst was the only component being added, then the crosslinking ought to occur anyway, just more slowly?

That's why I was unsure and asked the original question.

Re: Question about pre-cat lacquer

#5

Yes, no and maybe

Bill Tindall, E.Tn.

"It seems to me that if a catalyst was the only component being added, then the crosslinking ought to occur anyway, just more slowly?"

Lets take the easier example for which I know more about the chemistry, linseed oil and similar "oil" based varnishes. These react with oxygen which sets off a series of chemical reactions which hooks the "oil" molecules together to make the "cured" final film. Without a catalyst this reaction with oxygen will still occur but slowly. In a commercial varnish like Waterlox a cobalt compound is added which reacts with oxygen and in turn this product reacts with the oil through a series of complicated reactions to result in a cross linked film and regenerate the original cobalt compound. (I don't know all the details)

Now the question is whether given enough time will a catalyzed oil wind up the same place as one without catalyst? Probably not, but I don't know for sure. In both cases the varnish film will be crosslinked, but, maybe not to the same extent or in the same places. As the film cross links the diffusion of oxygen into the film is retarded and the ability of the oil molecules to move around to get the crosslinking sites together is hindered. The details of these differences could have a significant effect on the final film properties.

One could use similar thinking for the crosslinking chemistry of the precat lacquer. I know nothing about precat lacquer chemistry. But the amount of catalyst probably affects final film properties.

Furthermore, "slowly" might be years not hours.

Re: Question about pre-cat lacquer

#6

Re: Yes, no and maybe

AZ in Colorado Springs

Bill, thanks very much. I appreciate you taking the time to revisit this.

Re: Question about pre-cat lacquer

#7

Re: Question about pre-cat lacquer

don stephan

As originally used, I believe "lacquer" referred only to nitrocellulose lacquer. Unfortunately today there are a number of finishes that are not purely nitrocellulose and still call themselves lacquer.

According to a "Flexner on Finishing" article in the Dec 2014 Popular Woodworking, pre-catalyzed lacquer contains an acid catalyst, an alkyd resin, and one or both of melamine formaldehyde and urea formaldehyde, and MAY contain nitrocellulose as well.

Re: Question about pre-cat lacquer

#8

Re: Yes, no and maybe

TomD

If we are talking about the same thing, the products that catalyse due to the presence of a catalyst added at time of manufacture, often kick off when some other process occurs once the can is opened. This may be a change in PH when some chemical evaporates from the thin film, leaving the balance of material at a different PH. This means what is left in the can will last probably at least a few more days, but the days it last in an opened can may be numbered, bloxigen can help with that problem. Some of these products can be affected by stuff in environment like dust, sanding paper residue, and so forth.