Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Bandsaw tires coming off

Posts

Bandsaw tires coming off

#1

Bandsaw tires coming off

Joe Pack

I have a Grizzly G503 17" bandsaw that I have used from time to time for about 8 years with no problem. About 2 months ago a guy working with me used it to cut (yes, he did) a piece of Durock cement board, obviously ruining the 1/2" blade instantly...dull is not the word.

Having no replacement blade readily at hand, I went ahead and used this dull blade for some rough cutting (burning), using a lot of pressure on the blade. I was able to burn my way through a few pieces of pine and 1/4" plywood until...oops - the blade popped off.

I opened up the saw to replace the blade and found that not only the blade had come off, but the top tire did too. I easily worked the tire back into the groove, put the blade back on and proceeded to make another 4" cut/burn and....the blade and both top and bottom tires came off again. So, I walked away and found another job to do.

I finally came up with a new blade and installed it tonight, popping the tires back into place, installing the new 1/4" blade, adjusting guides, etc., then spinning it up by hand. Everything looked and felt good, so I flipped on the saw and it ran fine...until the blade started flopping. When I turned the saw off and looked, I found both the blade and top and bottom tires had come off again. Thinking I did something wrong, I repeated the process and...poof....same result.

When I spin up the wheels by hand, everything looks good. No wobble, good tracking....nothing wrong that I can see, but...

I have done some research tonight and find that this is not a terribly uncommon problem. Assuming all adjustments are within reason, and I think they are, the solution seems to be replacing the tires with urethane. With what I know now, this seems a likely solution. The tires on my bandsaw simply slide back on with very little effort. Everything I have read says this should NOT be the case; urethane tires should take a fair degree of effort to put on, not just slip back like mine do.

17" tires are hard to find! Grizzly has urethane tires (their picture shows a gray color), and I have also been able to find them at PS Wood (orange), but the large difference in price has me wondering...Grizzly's gray urethane run about $23/pair, while the orange PS Wood run about $49/pair. The Suffolk/Timberwolf page lists the orange models also, but, for the ones that fit the Grizzly 17", they say to go through Grizzly (but remember, the Grizzly catalog now shows gray - maybe or maybe not the same quality).

So, my questions: (1) Am I on the right track re: the solution for tires coming off? (2) Am I on the right track thinking the orange urethane would be better than the gray? (I only found the gray material on Grizzly's web page. The other urethane tires, regardless of brand and/or size seem to be orange, and in the same price range as those on the PS Wood site.

Any advice or comments would be greatly welcomed.

Re: Bandsaw tires coming off

#2

Re: Bandsaw tires coming off

del schisler

the heat from the blade made the tires go bad, replace with the orange and you will be good to go, i change mine with them and all is fine, they don't require glue , just heat in water and than put on , it is a pain to do it but it comes with a tool which helps, , my saw is delta which doesn't matter , tires go on the same way check here you can find a deal

http://www.google.com/#q=band+saw+tires

Re: Bandsaw tires coming off

#3

Re: Bandsaw tires coming off

bradkansas

Second the orange bands! I replaced my Delta bands with the orange.

Here's a tip.

I received a dowel with a metal spike with a nail-like head to help pry on the new bands from the seller.

Many years ago, during summers during high school, I worked in the 63rd. and State St. Sears tire department in Chicago. We used steel spanners and mallets to remove the tires from the wheel by hand while on the lift.

I remembered same when I began to install the new bands. I used the tool sent with the tires and a still shiny steel shank large screw driver to pry on the bands. I followed the dowel tool which hooked the rear edge of the tire with the screw driver and popped the tires on without heating in water. I used the screw driver to raise the front edge of the tires which slid down the screw driver shank into the groove in the wheels.

I installed both in no more than five minutes.

Happy holidays to you all and may you each have peace and health in the coming year and beyond.

Brad

Re: Bandsaw tires coming off

#4

Re: Bandsaw tires coming off

del schisler

i recieved the same tool, i heated the tires in water , but didn't see any reason after i installed them, they were cool any way ? i installed some on my friend's saw and didn't heat them, got them on fine ,

Re: Bandsaw tires coming off

#5

Re: Bandsaw tires coming off

I found that the orange urethane tires

I found that the orange urethane tires will permanently lose their elasticity the first time they're over-heated (what exact temperature I don't know) and fly off the wheels by centrifugal force thereafter; so I put the tires on cold and dry with a slick little tire-changer home made specifically for my 10" wheels. I found that band saw wheel housings are like ovens when you set them in direct sunlight. You have to keep those tires cool or you lose them. $.02

Re: Bandsaw tires coming off

#6

Re: Golf grips

TomD

Fine woodworking had an article many moons ago that described how to replace tires. You were supposed to glue them down somehow, then since the glue would bite, not letting the tire spread out evenly, you were supposed to mount a router to the frame and mill the tires level.

At the time I was into making golf clubs. The grips are installed over double sided masking tape, essentially. You can't begin to slide them on, so what you do is douse the tape with solvent then it slips on really easily, but quickly is welded to the grip. This works with bandsaw wheel also, but I would suppose that these days it is easier to just buy the urethane replacements. Still, it is a technique with quite a lot of applications.