Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Removing Rust Inside Pulley Hub

Posts

Removing Rust Inside Pulley Hub

#1

Removing Rust Inside Pulley Hub

don stephan

When I drove out the shaft, found out why I couldn't move the pulley sideways on the lathe spindle shaft (to align the upper and lower pulleys). There were some thickish areas of rust on the shaft and the inside of the pulley hub. With gentle use of an 8" mill bastard file and coarse steel wood I was able to remove the rust from the shaft, and most from the inside of the pulley hub. But there are still some dime sized areas of rust on the inside of the hub that the steel wool isn't affecting. What grit wet/dry paper could I use? The pulley is secured with a long key and pair of set screws, but I don't want to remove more metal than necessary. Thanks.

Re: Removing Rust Inside Pulley Hub

#2

Re: Removing Rust Inside Pulley Hub

Dick Coers

I would try a brass round brush with a 50-50 mix of acetone and transmission fluid. Or if you don't want to do the mix, Kroil penetrating fluid. With abrasive, it's pretty easy to hourglass the bore.

Re: Removing Rust Inside Pulley Hub

#3

get some RUST-OFF

del schisler

get it at sears and on line also with T-9 comes with it , use it on beds ect.

http://www.sears.com/boeshield-t-9-rust-protection-cleaner/p-00928468000P

Re: Removing Rust Inside Pulley Hub

#4

Because I have CRS.......Badly

Barry Irby

I used brake fluid for things like this. I had some old brake fluid sitting around and soaked a large very rusty bolt with a nut on it in the fluid for a few days. I was astounded that I could move the nut by hand when before I could not move it with a wrench. It did not make the bolt pretty but it sure did a job on the rust.

I probably would have used transmission fluid, but I forgot which one was supposed to do the job and used the first one I found on the shelf.

For all I know brake fluid and trans mission fluid are the same thing.

Re: Removing Rust Inside Pulley Hub

#5

Turned on to Evaporust *LINK*

Gary Smyth

I thought when I heard the name that it was some snake oil product. Bought a test sample and it worked great. Hands friendly, environmentally safe, reusable until the color indicator says otherwise. Got mine at tractor supplyone gal,$22. Lots of places other than there but don't stock in gallon or bigger containers. There are less expensive rust treatments-- and if they work for you, good on ya, but this stuff I don't worry about touching or disposing. Not flashy fast, a soak will do its job.


http://www.evapo-rust.com/

Re: Removing Rust Inside Pulley Hub

#6

Re: Removing Rust Inside Pulley Hub

rfcomm2k

Use contact cement to wrap a suitable sized piece of 400 grit wet or dry around a wood dowel. lube it with wd40. Move up to 600 or 1000 grit if you want a polished surface. Also take a few licks around the shaft with the wet or dry while ur at it.

Re: Removing Rust Inside Pulley Hub

#7

Re: Removing Rust Inside Pulley Hub

Ralph Lipeles

I take a short length of 1/2" dowel and saw cut it lengthwise for a few inches. I then clamp it in the drill press chuck, insert a piece of wet & dry paper in the saw cut and clean the pulley bore with the drill press turning slowly.

Re: Removing Rust Inside Pulley Hub

#8

Re: Yup

Larry Clinton At Frankfort, (Central) Indiana

That's the same way I have done it for about 50 years! I used what ever sandpaper was handy though the cloth backed paper does last a lot longer. I've done this mostly using a variable speed hand drill but a drill press may work as well or better. BE CAREFUL doing this as you can remove a lot of material if you use a coarse grit and loosen the pulley on the shaft. I normally use a medium (around 100 grit) or finer to clean out most bores.

As a side note, I also used strips of sandpaper to clean shafts of corrosion, it is easier to control than a file and doesn't leave flat spots. Just seesaw the sandpaper around the shaft and work your way around the entire circumference, again using a fairly fine grit. I have cleaned a lot of motor shafts in a lathe using sandpaper in this way. Just be sure not to let the ends of the strip get too close together or the paper may wind up on the shaft with your thumb ~ DAMHIKT.

Re: Removing Rust Inside Pulley Hub

#9

Re: Brass brush from plumbing

TomD

They have those brushes for cleaning copper, there is an outside one that does the shaft and looks like a donut, and an inside one like a bottle brush. Being brass, they can't deposit abrasive, or remove bare steel. Recently the cheapo stores have started carrying these for very low prices. Otherwise, getting one rusty and oily would not be economical, because the real ones were expensive. The cheap ones work well. A bit like this:


Re: Removing Rust Inside Pulley Hub

#10

Re: Brass brush from plumbing

Barry Irby

That looks like a really good idea. I will have to look at the ones I have. I thought they were steel. Even if they are steel and not brass, I still think they would work well.

Re: Removing Rust Inside Pulley Hub

#11

Re: Brass brush from plumbing

TomD

Yeah, I think they are steel. I have seen them both ways, but the pics when I went looking were all for steel ones which makes sense as they actually leave a scored surface on the Cu. But should be more sensible than the paper. Paper can be cool if you want more grip. Any left over grit may help hold things together.

Re: Removing Rust Inside Pulley Hub

#12

Re: Brass brush from plumbing

Ron Pemberton

I found brass brushes for cleaning gun barrels at Cabellas to clean the inside of collets for my routers. I can't remember the caliber but I got a set for 1/4 and 1/2 collets.