Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

OT: Drilling a porcelain/cast iron bathtub

Posts

OT: Drilling a porcelain/cast iron bathtub

#1

Ellis Walentine

OT: Drilling a porcelain/cast iron bathtub

Ellis Walentine

I don't usually post off topic, but this seemed like a likely question for our diverse group. I'm in the midst of a bathroom renovation and I've installed a new bathtub. I need to mount a bracket for a glass partition directly to the deck of the tub, which means drilling and tapping a hole in the tub. The tub wall is around 1/4" thick and has a shiny new white porcelain finish which I'd prefer not to ruin. The hole and surrounding area will be hidden by the bracket/channel, so I'm not too concerned about crazing or chipping becoming visible. Still, I may not be aware of any lurking snakes in the grass, and I'm not sure that my anticipated drilling method is the best. I'm planning to use a plain old jobbers drill bit, ground at a metal-drilling point angle. Would I be advised to use a diamond bit to cut through the porcelain before switching to the metal bit for the cast iron?

Any tips, tricks or caveats you'd like to share?

Ellis

Re: OT: Drilling a porcelain/cast iron bathtub

#2

Re: OT: Drilling a porcelain/cast iron bathtub

Dick Coers

Just an opinion, no practical experience. I'd use a diamond point in a Dremel to remove the porcelain before drilling the cast iron. I'd build a dam with putty around it, and have some water puddled in it. It would be tough getting the right size tap drill in diamond.

Re: OT: Drilling a porcelain/cast iron bathtub

#3

Are there circumstances

Gary Smyth

that would make it difficult to call a tile or kitchen/bath company in your area? Tile guys have to add shower enclosures a lot. I'm wondering if one you can trust might be willing to share.

Re: OT: Drilling a porcelain/cast iron bathtub

#4

Re: OT: Drilling a porcelain/cast iron bathtub

Terry in Edmonton

The installers that put in my neighbours glass doors used glue. I think it was a special type of silicone if memory serves me. I would talk to some pros about this. I don't really think you want to be drilling holes in you new and expensive tub.

Re: OT: Drilling a porcelain/cast iron bathtub

#5

Re: OT: Drilling a porcelain/cast iron bathtub

Jim Smith

Hello, I don't know about the porcelain part but cast iron drills and taps very easily,start with a small bit and work up to right size. Good Luck Jim

Re: OT: Drilling a porcelain/cast iron bathtub

#6

Ellis Walentine

Re: OT: Drilling a porcelain/cast iron bathtub

Ellis Walentine

Right, Terry. And apparently the tub mfr won't honor a warrantee if you drill their tub. Thanks.

Ellis

Re: OT: Drilling a porcelain/cast iron bathtub

#7

Ellis Walentine

Re: OT: Drilling a porcelain/cast iron bathtub

Ellis Walentine

Yes, I've heard that installers use PolySeamSeal to set these brackets. Being an old mechanical guy, I tend to think that a tapped bolt will be the more adequate solution here. I'd be willing to give adhesives a try, but I wouldn't want to risk catastrophic failure.

Ellis

Re: OT: Drilling a porcelain/cast iron bathtub

#8

Ellis Walentine

Local expertise

Ellis Walentine

You're right, Gary. I'm dealing with a plumbing company that does hundreds of bathrooms a year. They should be able to give me some guidance on this.

Thanks,

Ellis

Re: OT: Drilling a porcelain/cast iron bathtub

#9

Re: OT: Drilling a porcelain/cast iron bathtub

TomD

If by porcelain we mean there is something like pottery in the middle, then tapping that will likely blow it apart. Taps do not cut down, the force outwards. The way to bond to that is to set studs or your bolt sin epoxy. As oversized holes as you dare. But I would guess most of those holes are hollow, so getting something to bond to could be difficult.

I have seen a lot of shows where they put those shower glass doors in, and those are all bonded, not drilled.

Re: OT: Drilling a porcelain/cast iron bathtub

#10

Jason Roehl in Lafayette, IN

You know...

Jason Roehl in Lafayette, IN

...pretty much all modern skyscrapers have all their glazing held in place by an adhesive of some sort. It doesn't always hold perfectly, but I'm guessing your bathroom doesn't see the stress of a window on a skyscraper, either.

Jason

Re: OT: Drilling a porcelain/cast iron bathtub

#11

Re: OT: Drilling a porcelain/cast iron bathtub

Barry Irby

I would be opposed to drilling it. I my mind that is going to rust. There will be odd conditions caused by the difference in the metals in the tub and bolts.

I would bond it. Either PolySeamSeal Or find some of the super double stick tape type stuff they use for bonding glazing. I used butyl rubber tape to install a glass roof in a house I built thirty years ago and its still holding up. Bedding tape. It had a small tube in it to prevent it form completely compressing and the rest of it was soft gooey rubber. Come to think of it, I still have some and would be happy to send you enough to try.

Re: OT: Drilling a porcelain/cast iron bathtub

#12

Clint Searl

Re: OT: Drilling a porcelain/cast iron bathtub

Clint Searl

There's gotta be an adhesive that'll do the job better. Lotsa luck.