Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Burned out router

Posts

Burned out router

#1

Burned out router

paul woolson

I just had my beloved DeWalt router burn out. It started squealing and then got REALLY hot. I had the sense to shut it off before it caught fire or something catastrophic like that. Now I can't turn the arbor by hand. I assume the bearings have seized.

Does anyone know where to get something like this repaired? Is it worth the money? Thanks, Paul

Re: Burned out router

#2

Re: Burned out router

Barry Irby

I would probably try to fix it my self.

You can buy the parts online. Try places like Repair Clinic and you can find the web site for Dewalt and whoever they are affiliated with now. They also post exploded views.

You can also by replacement bearing at a local bearing shop, but be sure to get the high speed sealed ones.

The Dewalt site will also have a place you can enter your zip code and find a local shop.

Re: Burned out router

#3

Worth it?  Yes and no....

John in NM

Nothing like covering all the bases is there? :D

I've replaced bearings in several routers and sanders, and results have been mixed. Usually the bearings had worn to the point of vibration rather than seizing, and what I've usually found is that replacements would then be too loose in the housing and wouldn't last very long.

So I would say give it a try if you're up to doing it yourself, if you have to pay someone don't bother.

If you want to do it yourself, look for numbers on the bearing seal. You can get replacements from McMaster Carr for premium bearings, or VXB for cheaper ones. You may also have a local bearing supplier that will have them in stock. Go with sealed (rubber) rather than sheilded (steel).

Re: Burned out router

#4

Re: Burned out router

John McGaw

A close inspection is the first step to determining if a repair is worthwhile. If it is just one or two jammed bearings then you are probably good to go. If, on the other hand, one of the knackered bearings disintegrated and allowed the commutator end of the motor to wobble out of control then the damage to the brush holders and commutator might make it impractical. Ditto, if a bearing did jam and spun out in the housing then there could be enough damage that a replacement would not fit. Screams of agony from any spinning device are never a good thing.

Re: Burned out router

#5

Re: Worth it?  Yes and no....

Joseph Mulherin, sr

My Craftsman plunge router I had for 8yrs finally burnt up the upper bearing and gaulded the housing badly. Took it to the Home Depot in Palm Springs to be repaired and the guy gave me a price of $160 to do the repair. I bought the router for lot less than that so I just brought it home to keep and maybe repair someday myself. I went and bought a new one to about $78 to use in my table.

Re: Burned out router

#6

Thanks all!

paul woolson

Thanks for the replies.

I found a body for the same router and bought that for now. I also found some bearings and ordered them. Hopefully replacing them will then render me two working bodies. If not, I'm only out the price of the bearings.

Re: Burned out router

#7

Go to DeWalt Servicenet

Grant in Iowa

Paul,

If I were in your shoes, I would first go to DeWalt Servicenet and study up on how the router comes apart and what the bearings cost.

If it looks straight forward, and the bearings are reasonably priced, then have a look inside your router to confirm what is damaged. Carefully inspect the armature, brushes, etc. and study how the brushes get re-installed. Sometimes brushes must be held back during assembly by a pin tool or similar. If you find that the brushes can be removed through access holes before removing the end cap, it should be straight forward. Keep track of how the brushes are oriented and which one went where as you remove them.

Have a look at the bearings you want to replace. Some of these newer universal motors are difficult to get the bearings removed without a special tool, if at all. The average bearing puller may not always work due to tight quarters. You might even go ahead and remove the bearings at this point, keeping track of which one goes on which end.

Once you have it apart and have proven to yourself that you can remove the bad bearing(s), THEN order the parts from DeWalt Servicenet. It should be a safe bet that you can get it back together with the new parts, and therefore worth the price of the bearings.

I have been down this road before and ordered the parts without taking the tool apart (a $65 angle grinder). Mistake! I couldn't get the bearing off one end due to how it was constructed. The bearing was pressed down in a depression. Even with a machinist background and neighbor with a machine shop we gave up. You simply couldn't get under the outer race shoulder to grab it. So the bearings went in my parts drawer and the tool to the scrap recycler. Looking back, I realize now I could have maybe welded something on the bearing to give me a way to pull it, but that might have done more damage to other components, since the commutator assembly was right there and riveted in place. Not all modern tools are meant to be repaired is the point.

Learning that has definitely changed my buying habits. Now I look carefully at the tool to see that it is made to come apart for service. I intend to keep tools for a lifetime, or until they fail. I buy tools with that in mind now.

Just trying to save you the same grief by sharing my experience.

Regards,

Grant in Iowa