Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Glueing plywood to polystyrene

Posts

Glueing plywood to polystyrene

#1

Glueing plywood to polystyrene

Tom

I need to make some crosses for the from of our church. They need to be quite light weight because of what they will be hung from. My thought is to laminate 1/8" plywood over poly styrene, this can be done in my vac bag set up.

What I need is the proper adhesive.

Thoughts?

Thanks!

Re: Glueing plywood to polystyrene

#2

Re: Glueing plywood to polystyrene

Bill Tindall, E.Tn.

I have used white glue to fasten polystyrene foam together, so I suppose it will stick wood to the foam too.

Re: Glueing plywood to polystyrene

#3

Re: Glueing plywood to polystyrene

Joe in a Cleveland suburb

You might find a solution here:

http://www.thistothat.com

I don't know if this site is good or not. I recall seeing it posted here over the years.

Re: Glueing plywood to polystyrene

#4

Re: Glueing plywood to polystyrene

don stephan

Test whatever is recommended. I was experimenting with blue high density Styrofoam this spring and the glues I tried weren't bonding well. Finally decided to scarify the surface of the Styrofoam first and repeat the experiments. Haven't gotten back to it yet.

Re: Glueing plywood to polystyrene

#5

Clint Searl

Re: Glueing plywood to polystyrene

Clint Searl

Polyurethane construction adhesive or silicone caulk.

Re: Glueing plywood to polystyrene

#6

Re: Glueing plywood to polystyrene

john Veerkamp

they make special adhesives for the poly. Be careful and test what you use first. Some will melt/partially dissolve the poly. damhikt.

Re: Glueing plywood to polystyrene

#7

Re: Glueing plywood to polystyrene

TomD

We use epoxy for boats where those two materials are joined. But could be overkill in your app. There are some white glues, maybe weldwood, that mention a wide variety of other materials. I think also that polyurethane might work if you moistened the ply. It will stick anything. None of them melt foam.

Re: Glueing plywood to polystyrene

#8

Re: Glueing plywood to polystyrene

Yonak

We used to use hot melt glue (set to the right temperature) for EPS fabrication. I think Clint's idea of construction adhesive is good, too. ..As long as the adhesive isn't petroleum based it shouldn't degrade the foam.

Re: Glueing plywood to polystyrene

#9

Re: Glueing plywood to polystyrene

John McGaw

I made a lightweight slab for my downstairs mantle and used EPS as the core with a thin skin. Epoxy worked great for the sticking duties although covering the large areas made it anything but a cheap fix.

Re: Glueing plywood to polystyrene

#10

Re: Glueing plywood to polystyrene

don stephan

Would have been one of my tests, but I need to make torsion box with 1/4" plywood skins and construction adhesive is so stiff I expect the plywood would not lie flat without a lot of uniform pressure pressing it down, maybe more than a vacuum bag can generate.

Re: Glueing plywood to polystyrene

#11

Re: Glueing plywood to polystyrene

John b chicago burbs

Loctite and 3M both make an adhesive spray suitable for foam. I have used both products with great results, and are available at box stores. john b.

Re: Glueing plywood to polystyrene

#12

Re: Glueing plywood to polystyrene

Tom

Decided to do a test sample this afternoon. I used Titebond and sandwiched 1/4"ply between EPS. Will report back tomorrow.

Re: Glueing plywood to polystyrene

#13

It will take a while to dry

Bill Tindall, E.Tn.

Moisture may not travel through the foam readily and there is not a lot of wood to soak up the water. Might take a day or two of room temperature curing.

Re: Glueing plywood to polystyrene

#14

Re: Glueing plywood to polystyrene

John Lucas

I haven't read the other responses but Clear Silicone Caulking is what I would use. I've used it a lot to glue glass to wood and it works great. Also works to blue board and white styrafoam to each other. It won't melt the plastic.

Many years ago they glued blue board letters to the wall above our store in the mall. 20 years later they had to tear them off the wall. that is good stuff.

Re: Glueing plywood to polystyrene

#15

Re: Glueing plywood to polystyrene

Tom

I had thought of using silicon but the size of the cross 3' x 5' both sides seems to make it a bit impractical. Plus I am thinking of also sandwiching a solid wood edge around the perimeter.

Re: Glueing plywood to polystyrene

#16

Re: Glueing plywood to polystyrene

Rick W

I have successfully glued a 1/8" lauan plywood skin to a styrofoam core using 3M Fastbond 30 water-based contact cement. I gave both surfaces two coats each of the contact cement, and pressed the panels in my vacuum press.These were panels about 1-3/4" thick, and 3' X 7', for a museum traveling exhibit.These panels were displayed indoors, so I don't know how they would hold up with exposure to the weather.

The panels held together well for the 5 or so years the exhibit was on the road. I still have a test piece I did some 15 years ago, and it's still solid.

Rick W

Re: Glueing plywood to polystyrene

#17

Re: Glueing plywood to polystyrene

TomD

"Would have been one of my tests, but I need to make torsion box with 1/4" plywood skins and construction adhesive is so stiff I expect the plywood would not lie flat without a lot of uniform pressure pressing it down, maybe more than a vacuum bag can generate. "

That is the kind of thing we used shopvacs and epoxy for. I would agree about crushing out the construction adhessive, but urethane glue is similar, and can be vac bagged. Epoxy is pretty much always the best, but it might be regarded as overkill, and is expensive in some places. With that much coverage, the glue isn't going to be free for a project this size anyway.