Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Is this a good application for Anchorseal?

Posts

Is this a good application for Anchorseal?

#1

Is this a good application for Anchorseal?

Tim Greif - West of Chicago

LOML wanted some stump seats for the burn pile area at our river house. Folks like to sit around and watch a fire while socializing and enjoying beverages. We cut up some logs and they work well. A neighbor had done something similar a few years ago and mentioned that all the seats rotted in contact with the ground fairly quickly, and eventually became fuel for the burn pile. I was wondering if sealing the end surfaces with Anchorseal would solve, or at least prolong the life of these seats. I've never used Anchorseal so I'm in the dark as to what to expect. Any suggestions?

The pic below shows the seats laying on their sides after cutting. They are now upright with one end on the ground and the other end on your bumm.


Re: Is this a good application for Anchorseal?

#2

Re: Is this a good application for Anchorseal?

Bill Tindall, E.Tn.

Wood rots where it stays wet. As woodworkers know, if you keep wood dry it will last centuries. So the objective is to keep the end in contact with the earth dry, or at least as dry as the rest of the log, which will rot anyway after some time depending on where you live. Anchorseal is essentially emulsified wax. It will be a barrier to water, in either direction, so it might help. Soaking the end of the log in some tar, driveway sealer, or similar could work too. Adding some mold killing ingredient would be even better. But in the end the life will be limited by the wood species and how wet the area stays where the wood is at.

Re: Is this a good application for Anchorseal?

#3

Re: Is this a good application for Anchorseal?

Dick Coers

Bill is right, it's about the wood drying out. If you put them on a bed of course gravel they will last longer. They may last longer if the long grain is in contact with the ground, but not much longer. Nature has this great system set up to return the nutrients to the earth. Bugs, worms, bacteria, and fungi are all around us to do just that. You are trying to beat Mother Nature, and that's a loosing battle.

Re: Is this a good application for Anchorseal?

#4

Re: Is this a good application for Anchorseal?

mdclor

If you are lucky and your seats happen to be white oak or black locust, they will last a long time with no treatment. An old farmer used to tell me that I should use black locust for fence posts and replace the holes every 40 years. :D

Re: Is this a good application for Anchorseal?

#5

Re: Is this a good application for Anchorseal?

Bill Howatt

While it certainly slows drying of wood, it is not totally impervious and being what appears to be some kind of wax emulsion I don't think it would last too long being dragged around the ground. I also wouldn't want to sit on it without some intermediate protection layer.

I think the best thing would be to build some short feet out of something like plastic so the stump bottom would not rest directly on the ground.

Anchorseal is used extensively by turners to keep the wood from drying out too fast but an alternative, although most agree, not as good, is to paint the end of the log with latex paint. You could use several coats to build up a good barrier.

I would do both top and bottom.

Bill

Re: Is this a good application for Anchorseal?

#6

NO

Mark Mandell - Gone Round In New Jersey

Anchorseal is a wax emulsion. Ut's ised to slow drying of cut-ends of logs to retard drying checks in the end grain. Although it leaves a wax coating when dry, the emulsifies are still in the wax and rain will re-wet and then rinse off the sealer.

If you want your stump seats s last raise them off the ground and let them dry. Putting them end-grain down will just keep the wet and encourage mold and rot to soak up from the ground. The fungi that operate to break down wood remain active while the wood has a moisture content above 18-20%. Wood that's not in contact with the ground will usually (depending on your area) naturally dry to about 15% if it's not sealed.

Sealing your fresh-cut logs will keep the moisture content higher longer and produce just the opposite result from what you seek as it will encourage the rotting process.

Re: Is this a good application for Anchorseal?

#7

Anchorseal is fairly permanant

Bill Tindall, E.Tn.

I coated a log which I intended to store a while and then never sawed it. It was coated last spring and it still is check-free in spite of an above average rainfall. The coating is beginning to degrade, I suppose from sun exposure.

Technically, Anchorseal is a latex like latex paint, that is a suspension of wax particles in water with a coalescing solvent. Once the wax particles coalesce into a coherent film as the stuff dries water will not turn the film back into suspended particles.

Were it an emulsion- a suspension of an oil in water- the oil could reemulsify upon exposure to water.

Re: Is this a good application for Anchorseal?

#8

Re: Anchorseal is fairly permanant

Mark Mandell - Gone Round In New Jersey

Since I use it on wet rough turnings and then remove it by simply running it under water, there may be different formulas. I know my dried-up applicator brush rinses clean with just water.

Re: Is this a good application for Anchorseal?

#9

OK, how about PT feet on these?

Tim Greif - West of Chicago

First of all, thanks for the replies. Sounds like I need to isolate them from the soil (which is very permeable and usually dry) to eliminate the bottom end grain from staying wet. I'm thinking some pressure treated 2x4s cut into short flat pieces to act as legs and screwed flat onto the bottom of the seats with stainless deck screws. Not going to be moving these much due to how heavy they are. Is this a workable idea?

Re: Is this a good application for Anchorseal?

#10

Sounds Like A Plan 


Re: Is this a good application for Anchorseal?

#11

I wouldn't do anything to them,

Keith Newton

The beetles are going to get into the bark and sapwood soon anyway and break that down, so I would just plan on replacing them yearly.

Besides, the best fishing worms love to live under stumps left on end like this. You don't even have to dig, just tip and roll them aside, and pick them up.

If there is enough wood available in your area to have bonfires, there probably is enough to replace them when needed.

Re: Is this a good application for Anchorseal?

#12

Re: OK, how about PT feet on these?

John Lucas

Being a turner I use a different approach. I drilled short holes in the bottom with a 2 1/2" forestner style bit and then turned very short feet out of pressure treated wood to fit in the holes. Then coated the bottom of the feet with epoxy. I put a coat of epoxy on the top of the logs to slow down the drying and repel water. they lasted for a long time like that. They did eventually split and the epoxy on top flakes off. I wondered about hammering copper flashing around the tops to really shed the moisture and sunlight but decided that was too decorative for what I was using them for.

Re: Is this a good application for Anchorseal?

#13

Re: OK, how about PT feet on these?

James Heaston

I'm pretty much w/ Keith on this, but to add to the longevity & keeping w/ a rustic appearance put rocks under 'em. Use one flat-ish one or 3 or 4 like legs. Just so air can get under 'em. ;)