Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Will epoxy stick PVC

Posts

Will epoxy stick PVC

#1

Will epoxy stick PVC

Bill Tindall, E.Tn.

Long story but the summary is I need to join two pieces of PVC pipe with a coupling that needs to easily slide on the pipe which means a small gap between pipe and coupling. Epoxy fills gaps. But will it stick PVC?

Re: Will epoxy stick PVC

#2

Re: Will epoxy stick PVC

Keith Newton

I would scuff sand it to give it something to bite onto, then of course mix in a filler to make it into a paste thick enough to stay put until it kicks.

Sounds like something that a Fernco coupling is designed for though.

Re: Will epoxy stick PVC

#3

Re: Will epoxy stick PVC

TomD

Yes. There are two ways. One is to hit the pvc with a torch just long enough yo haze the surface. That is oxide, and the glue will bond to that. My boat has scuppers and other through hulls bonded that way, and it works.

Stronger still is to clean and glue it with the regular pvc glue, and bond epoxy to that. But that sounds like it would grab in your app. It is however stronger by a lot, but for stuff like bonding the pipe to wood where the wood will not have the cement on it also.

Re: Will epoxy stick PVC

#4

Jason Roehl in Lafayette, IN

2nd the Fernco!

Jason Roehl in Lafayette, IN

I have a friend who used to work for the local city water department, supervising a construction crew (hands-on, in the field). They used Fernco couplings to repair broken water mains up to at least 6 or 8" (probably larger, too). I got the opportunity to watch them repair a few water main breaks--they have some interesting techniques and tools for when they can't shut down a main with a valve (one's called a "hydrostop"--they drill a large hole in the pipe and insert a rubber bladder that is then filled with compressed air to seal off the pipe upstream of the break, then it's replaced with a valve).

Anyway, Fernco is the way to go if you're talking about a PVC line repair, whether it's a drain line or a pressurized supply. The appropriate size should be available at a nearby big box store (possibly even a local hardware store).

Jason

Re: Will epoxy stick PVC

#5

Clarification?

Mark Mandell - Gone Round In New Jersey

You can get a slip coupling to fit your pipe at the Borgs, but it seems you want the coupling to continue to move along and over the joint after the pipes are joined. If so, then you need to do a butt joint on the pipe with only the thickness of the pipe wall as the joint surface. If THAT is the correct view of what you want to do, the answer is No Way.

THAT said (and if I'm correct in my view of your goal) you might be able to fagazy an internal coupling with a piece of pipe that you section out so it fits INside your 2 pieces and is glued to the inside surface of the pipes leaving the outside surface unobstructed for your slider. It would, however, not pass a pressure test if the pipes were to carry water.

Re: Will epoxy stick PVC

#6

Re: Will epoxy stick PVC

del schisler

here is a google search go here if you have already and pick and read , if their isn't enough space to use a reg. coupling if you only can lift up one piece their is a coupling that doesn't have the stop ridge in it , and can be sliped on one end and than mark on the other end of the piece so that when you glue both pipes and slip the coupling back you stop on the mark , if this is not the case than go to the google , epoxy will stick when prepaired for it ,

Re: Will epoxy stick PVC

#7

reply to posts

Bill Tindall, E.Tn.

it is a water line with bursts of up to 200 psi on it at times. I only have a small access man hole to make the joint 30" below grade with concrete on one side and packed driveway on the other. There is almost no flexibility. I could not find a repair coupling in 3/4 " so I made one by removing the ridge on a regular coupling with the lathe and opening up the internal diameter a bit so it will slide over the pipe easily and not seize before I get it glued and in place over the butt joint. The fit is snug and regular thick PVC cement will likely work fine to fill the somewhat larger gap than in a non-repair slip joint. If epoxy would have been better I would have used it.

I was unable to find a Fernco spice in 3/4". I did get a compression splice with rubber washers but it looks risky compared to a solvent welded joint and I would rather not rely on it.

This all resulted from installation of a new pressure reducer at sheep shed that turned out to be 3/8" longer than the defective one. Laying on one's belly reaching into a 30" deep hole to work on this mess has not been better than a day in the shop making sawdust.

Re: Will epoxy stick PVC

#8

Re: Data you will respect

TomD

These guys have their own lab, some of their testing methods have become engineering standards. One of the borthers, Meade, is an engineer.

Unfortunately the article that deals specifically with PVC is not on the net, but the process for PVC is described in the Gluing Plastic article.

http://www.epoxyworks.com/26/pdf/Gluing_plastic_Gflex.pdf

http://www.epoxyworks.com/28/pdf/Plastic_engine_cover.pdf

http://www.epoxyworks.com/16/glueinglumber.html

http://www.epoxyworks.com/17/corian.html

"To flame treat a plasticsurface, hold a pro

-

pane torch so the flame just touches the sur

-

face and move it across the surface at a rate of

12 or 16 inches per second. Keep the torch

moving and overlap the previous pass slightly.

When done correctly, the surface will not dis

-

color or burn in any obvious way. This tech

-

nique oxidizes the surface and improves

adhesion. For best adhesion, bond to the sur

-

face within 30 minutes of treatment."

Re: Will epoxy stick PVC

#9

Bill

del schisler

i used to work at HD part time and they had coupling's like you made by removing the ridge in the middle so that the coupling could slide on the pipe the full length if needed to. glad you got it fixed, not a good day on the belly and reaching down a hole.

Re: Will epoxy stick PVC

#10

Re: reply to posts

Barry Irby

As others have mentioned, I think a repair or slip coupling is available. I have always called the couplings that slip on and then slide back and forth Dressler couplings, but that might be a brand name. Not sure about the 200 PSI though.

Another choice might have been a Shark bite or Gator Bite but you need enough room to flex them on. I have been impressed with those. Expensive, but easy. No muss, no fuss, no glue, just stick them on and seat them. Great where a torch would be a problem.

Re: Will epoxy stick PVC

#11

Re: I would not use epoxy!

Larry Clinton At Frankfort, (Central) Indiana

Bill, the PVC cement is actually a solvent for the PVC material, epoxy most likely would not actually dissolve the PVC surface, therefore it would depend on adhesion only. I have not seen the "slip couplings" described above but would use one if you can find it. In my side contracting job I worked at for several years I installed miles of PVC without any failures. If you are concerned about the gap, you can use a file on scrap PVC to make a PVC powder then thin it with PVC cement to make a thin slurry and apply it at the time of installation. I would definitely prime the inside of the coupling and the pipe well then test the fit after the primer dries. Then I would install the "slurry" and slip the (your) coupling into position. Should be gold!

Re: Will epoxy stick PVC

#12

Repair done, with exceptional aggravation

Bill Tindall, E.Tn.

I truly hate plumbing. What ever seems simple invariably turns into endless complications. In this case I was almost standing on my head working in a man hole that enabled access to the pressure valve and shut-off. Recall that the replacement pressure reducer was 1/2" longer than original with no flexibility at either end.

In the end I made what is called a repair coupling, a slightly over=sized coupling that will slide down the pipe so that a joint can be made with out having to lift pipe from the ground. Upon installing it I discovered that the piece I made to go between valve and regulator was 1/32" too long (how does that go, measure twice and cut twice and then measure one more time). That lead to a struggle and a cut o-ring at the regulator. Gasket repair to the rescue, eventually.

Oh, I used gobs of thick PVC cement.

Next time I will break out the concrete so I can get at everything better.

Re: Will epoxy stick PVC

#13

Larry

del schisler

here is a google search for the 3/4" slip coupling with out the stop , HD has them ,i used to work part time their, at least Bill got it done here is the link http://www.tractorsupply.com/en/store/ldr-3-4-in-pvc-schedule-40-slip-coupling

Re: Will epoxy stick PVC

#14

Re: Thanks Del

Larry Clinton At Frankfort, (Central) Indiana

I have to admit, although I worked as a professional plumber / contractor for several years (among other contracting tasks) as a second job, I had never used or even knew this existed. Guess I never ran into a job that needed this ~ or I found another way around the problem! Thanks for the information.