Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

*** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

Posts

*** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

#1

Ellis Walentine

*** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

Ellis Walentine

Yep, and actually on time for a change...

This month I'd like to pursue a question that was sent in by one of the readers of our bimonthly "News & Views" column in Woodworker West magazine.

USED WOODWORKING MACHINERY

What to look for, what to look out for, and the pros, cons and relative merits of new and used machinery.

I'm sure there is plenty of experience out there on all sides of this issue, and, as usual, we want to hear what you think. We'll distill your replies and include them in the next column, due out in mid October.

Thanks for participating!

Ellis Walentine, Host


Woodworker West magazine

Re: *** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

#2

Re: *** SURVEY: THE IDES OF SEPTEMBER ***

Thomas S Stockton

what I look for overall is condition since I'm not interested in restoring something at this point. I want something that I can plug in and use with minimal repairs it doesn't matter if it is painted bright pink if it works and is within my budget I will get it.

I think another important aspect is patience and a little research, compare the cost of used vs new sometimes new is way more cost effective. I also like to check ebay, craigslist and other sources to see what's out there and general prices before starting to really hunt for something.

One other really important tip is to set it up in your shop and see how it runs and if it is set up correctly before tearing into it, that way you will have a base line to go from and know if the problem you are having was there before you got it or something that happened after.

I also think that older is not necessarily better, there are some great deals to be had on newer machines that perform really well and have things like tersa cutterheads,insert cutters and modern guards that are similarly priced to older things

Tom

Re: *** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

#3

Re: *** SURVEY: THE IDES OF SEPTEMBER ***

Bill Tindall, E.Tn.

If you have the knowledge to buy wisely and the knowledge to fix parts such as bearings that were designed to be fixable a used "light industrial" quality tool will be cheaper and can be better performance and durability than a new tool of similar capability.

For me light industrial used tools offer me a way to get better tools than I would consider buying at new prices.

Re: *** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

#4

Re: *** SURVEY: THE IDES OF SEPTEMBER ***

TomD

The primary question, sadly not elucidated in the OP is why one would want to buy used machinery. This really is the nub of the issue. For instance, if you want to recapture what it was like working with your dad as a kid in his shop; or want to use pedal power 19th century tools; or want tools that are no longer made; or want tools that look nice rather than like a central air conditioner; then you pretty much have to buy used tools. That cuts down on the possible objections that might otherwise be raised about their purchase. I have done all these, sometimes more than one on the same day. I once went and visited a guy who had assembled a lot of tools, enough for his intended second shop. Unfortunately he had had to drop his plans, and was selling his machines. He sold me a foot powered mortise machine (pretty, no longer made). At the same time he sold me a really nice Rockwell table saw, 9 inch, just like the one my dad had, and that I still have at the farm. Except we had the contractors version, this one was a mint version in cabinet format. It had a really elegant cast base (pretty, Dad's shop category, cheap [$50]).

The most common reason for buying second hand might be the price. A 50 dollar saw they couldn't make today for 2K is pretty persuasive. My experience along those lines is:

1) I never found the secret to getting tools cheap, but over time they started flooding in. I have had this experience on a number of things, and the problem is that ridiculous situations show up at fabulous prices, normally around the time you have already bought everything. Which is no longer as useful as it might be. I could go into the biz now, but I don't want to.

2) Online sales fall into commodity stuff, you can pick up anywhere. So you have the tablesaw for virtually free. Easy to learn these markets lots of ads. You have the entry level tools that people switch out of. I needed one of those entry level drill presses for CNC parts, but you could buy them just to get the motor, or to fixture a drill press. There was literally one every highway exit.

At the other extreme there are the speciality things people want like say Inca tools that are easy to find in my area because there are few things (looms and Inca nick nacks) to clog the listings. You will probably find more Inca in affluent parts of the country, or areas around Garrett Wade or Lee Valley stores because they sold the lines. Maybe tough in Alabama, but then there were rocket engineers in some places there also.

Other than mastering Boolean search tools, I find a critical thing in finding listings whether selling or buying is to figure out a key word that cuts through irrelevant listings. Some listing are just nightmares to sort. Even better is to figure out the words people miss-list deals under. There is nothing like checking constantly. A few of my best deals came from reading a lot of ads and spotting something the person selling didn't want to sell. I never did this intentionally by say looking for "and I also have", but on two occasions I got my most prized tools from "and I also have" listings. I never asked about say a tool in the background, to see if it was for sale, though I guess it could happen. The "and I also have" listings, are afterthoughts so to boot you can sometimes get them cheaply.

When you want to buy something my strategy on getting the deal, assuming I really want it, is to say I will pay cash, and it is sold assuming the condition is as listed. You can get price concessions later if you need to. I think part of the reason I do well is because I like old people, enjoy their stories, am straight but serious with money, and am willing to take a risk, don't cry or call the lawyers when I end up with the short end. It is hard to characterize the approach, it will be different for everyone. Most sellers of woodworking stuff are pretty nice people and you are in their homes. If you treat them as you would expect to be treated, they will show you the stuff behind the curtains, and maybe later ask you to liquidate their shop (mixed blessing).

Safety. Use common sense when entering situations where you could be walking into John Wayne Gacy's basement voluntarily. You will be indoors, in a situation were easily weaponized stuff is lying around everywhere. Be polite and cordial to everyone, but formulate a plan to kill them, as the saying goes. This cuts both ways, when ladies come to visit I always have them met by my wife. That may set them at ease, though it shouldn't in the Province where Karla plied her trade.

What should you buy?

Obviously on price, there are opportunities to get a lower price on recognizable catalog items. These are just straight forward bargain hunting. You obviously have to have a clue on the financial depreciation of various types of gear; which ones are more likely to have motor or bearing problems. With the internet all this stuff is out there. Then you just go after the deals that make sense to you.

Buying actual old, possibly antique tools is more of a mixed bag. What should you buy. I like saws and drill presses. Particularly table saws. The US market design wise is way behind on saws. If it had progressed as in the EU, buying a 1950s table saw would be ridiculous. But it has retained the basic flawed architecture and attached expensive stop gaps like fences, and sawstop. On that basis, the beautifully machined, and particularly the smaller saws of an earlier period are super buys and tolerably safe. Many of these old saw used round bars for the fence, and may have minor mounting challenges for the newer fences. Old saws may be more accurately machined. Motors are normally easily detached and serviced or replaced,

Bandsaws. The newer ones are basically euro, and for general work and resawing are preferable. The old ones like a 15" general can be extremely high quality at the right price. The rangy Victorian ones can be great for cut out work. Usually will require addition of safety stand-off gear.

Planers are complex and hard to fix, and parts may be missing. I generally avoid them, but when you come across the only driven on sunday type planers, and they can be a good deal. They are a classic example of tools that may be a nightmare to dust extract. Extraction can be a major problem when buying older stuff, keep it in mind.

Around this point it is time to talk about moving stuff. Don't lift it, or ask your friends to lift it. The cheapest way to move really heavy stuff on ground level is with an engine hoist, it also comes in handy for pulling small trees out of the garden. Moving is a whole other subject...

Jointers. Three things here: Materials and machining matter here, you have a cantied structure that is heavily loaded, you have few major parts, that is a plus for old stuff well made. You have some very real dangers, as in badly designed guards, excessive gaps, square heads, and your back while moving this stuff. You have some issues around how tools are designed to be used. You might want to buy a huge wide jointer to face plane your Krenov style cabinets, but it may have been designed to plane timbers, and so the gap might be really dangerous around short little pieces of bookmatched wood.

Drill presses. Good area for oldish ones, though it can get ridiculous with exposed wide belts, etc... However, these machines can be killers, if you buy one for 50 bucks that has a 5 horse 3 phase motor, be aware it can wring you out like the wash. Size the motors for the work you are doing, not the size of the machine. A gravity switch is a good idea.

I could go on, but I am going to hop to something other than the tools.

Re: *** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

#5

The Big Take-Aways, And Big Ideas

TomD

Bundles. When you buy second hand or old machines, you usually do not pay extra for stuff. So you will find that similar machines price at the same dollar amount while one has a few missing parts, and the other has a chest of hundreds of items that each has an average price of $100 each. Seriously. People want money for the machine, pretty much the same money. I bought a shaper that was almost out of the box mint, another serious person tried to sell me the Road Warrior version of rusty parts for more money than I paid, I think he wanted 900, and I had paid 600. But these were rare, and at one level they are good value as to what you get at almost any price compared to what they make today, but wait for the mint "kit" if you have the time. Having time and some extra cash to front, even though you probably can get the cash back, is key.

Models. Similarly, there are often different models, and the models will often sell for the same money, though in the day they might have been very different in price. Some of the models, are way better than others. Say the Toolroom Lathe, VS. a consumer model meant to follow a doctor home (or my example of the cast base vs contractor saw). But, sometimes the industrial model is way worn out, and the craptastic home version is a better deal. This can also apply to models with less features on them, could be less desirable, and therefore less worn. Was it born in the time of 24 hr war production. You have to figure these things out. What 4 things should you look at that are the honey traps. Can you recognize the most common things that break, or wear. Google it. Get a good rule and dial indicator, that should set you back 10 bucks. Know the machines that are super accuracy related TSs, jointers, while drill presses (for our work), planers, lathes, bandsaws, may or not require the same level of care.

Investment value. Probably few tools really have it. You are more likely to make a kill on the low initial sale price. That said I try to price stuff so I don't loose more than 10% on resale. You can get killed, or you can kill. I pretty much am happy paying a minor premium for having the experience, or use of the tool, so I would fall in the middle somewhere. But I have a fair amount of money tied up in these tools. When I went to pick this stuff up, I was buying a lot of it from guys around 75 years of age. I wonder where the replacement people are to buy us out. Is there going to be a point where we hit an age group that is 100% not hands on, and they don't want to buy these tools from us. They don't make them any more, but whether there is a long term market is hard to say.

Materials. One often hears people talking about how bad the new Chinese tools are. It is pretty much all true, particularly on machine tools. Machine tools are more naked, you can almost read the quality of the materials like wood grain. You don't have to be special to see these differences. When I started to acquire old machine tools it was just obvious. This is not to say that newer tools aren't good. You can write your way out of any corner, and in manufacturing you can do things to make new crap sing. We will get to that.

Relatives. Should you look for situations where the bereaved are getting skinned? Ethics aside I would say no. I normally find that products in the hands of the original owners are in far better condition. Today, a relative can easily search a price on the net, but that won't stop them breaking or loosing parts when they emptied the house, and you probably can't see the stuff running. Exceptions abound, but overall, I prefer to look for quality than price. You can get both if you are patient.

Local. Canada gets very little stuff compared to what the US has, and typically the old second hand market was very expensive, somewhat as a result. So when I started looking I even made distant trips to the US to find stuff. But I learned that I can get almost anything locally. Toronto is big, and the stuff is out there. The internet provides the link, and keeps prices reasonable. But my point to guys in the US who may not have tried the second hand market is that at least at first, I would assume that if you can't find it, it is you, not the lack of availability locally. Give it some time and a chance. Three of my favorite items were ones where I considered going as far as Alabama. Yet ultimately the items were found 1hr, 10 min, and 20 minutes from my home. And I don't network.

Types of machine. Ok, this isn't saw vs jointer. I am talking about the kinds of markets where second hand machines are a lot better, but may or not measure up. I also look for sewing machines, or did at one time. Some old machines are high quality you can pick up for as little as 20 dollars; Singer cast iron machines that were designed to sew 4000 stitches a minute indefinitely. Modern asian machines might as well be made of cheese. So obviously one should only buy old sewing machines, right? Well if you look at a Randall (youtube, kinda cool machine), nobody makes anything like that, as far as I know; Patchers haven't changed; but speciality stuff for hobbyists and crafts like sailmaking, the new stuff is where it is at. Machine tools, the new ones made by say Grizzly, are pretty much patterned after pre-WWII machines, the originals are better and far cheaper. But CNC obviously is new, and modern manual machining requires modern tooling. Spinning, old stuff when people really spun, often were required by law to spin, not useful for modern craft spinning. etc... Pretty obvious, if it is some freaky hybrid, like modern hand planing, the new stuff may be "better". What about the spiral power planer head with replaceable edges? The better importers have figured out how to add their expertise to some Chinese junk and make it highly desirable. Why is it there isn't a decent Chinese bowl/hobby lathe? Has to be the single easiest tool to make, they could clean up.

Concepts to live by. A pal once told me he had short term, long term, and dream goals. He was a broker so his dream goal back around 1990, was to generate 1 million dollars of retail commission in one day. Same thing here. Be on the lookout for the practical stuff you need, but also keep your eye on the big score. I have had a few on a big scale for me... The biggest I know about was from Oregon, and it was machine tooling. A Doctor, I think, was hoping to take up metal working in his retirement,and built a huge shop, and stocked it with every imaginable tool, a hundred or more lathe sized tools, for all types of work. He never got around to it, and some local guys got called in to find a treasure trove of every imaginable tool, still all in their original crates. It happens.

Is it all worth it. My short take is yes for machine tools, and no for woodworking. Woodworking is specialized I can't think of an Asian, or antique lathe that I would consider. There are also some traps that can affect your productivity. I have stuff in the shop getting in the way, that I plan on reselling. I think that while I am happy with the journey, that I lost more than I gained as far as efficiency is concerned. Sometimes I bought 4 things to get one, and then the other stuff hangs around. Whenever I accidentally see Storage Wars (cancelled the cable this month), I love it when the guy makes a killing, on say, 20 000 pairs of tube socks, or some such. "doubled my money!". Yeah right, you soon learn why there is so much money in sales...

Re: *** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

#6

Bart Goldberg

Re: *** SURVEY: THE IDES OF SEPTEMBER ***

Bart Goldberg

Several years ago, I replaced my Jet 6" jointer (that I had purchased new) for a used 8" Delta DJ-20, from a local shop that was going out of business.

The machine had a fair amount of wear, but nothing that needed to be replaced, or made the machine unusable. It had a few nicks, etc. but was in a totally usable condition, and I was able to try the machine out before buying.

I paid about 1/2 what a new machine would have cost me. Within a year of buying it, I did invest in upgrading it with a Byrd Tools spiral cutter head. Interestingly enough, while replacing the cutterhead, I discovered that their was a rather annoying cutter head shield that was intended to prevent you from contacting the cutterhead from the dust port. I removed that shield as part of the upgrade, and the dust collection for the machine improved by a huge margin. So, in general, I am happy with my purchase of a used Jointer.

Regards

Bart

Re: *** SURVEY: THE IDES OF SEPTEMBER *** *LINK*

#7

Re: *** SURVEY: THE IDES OF SEPTEMBER ***

Larry Clinton At Frankfort, (Central) Indiana

USED WOODWORKING MACHINERY

What to look for, what to look out for, and the pros, cons and relative merits of new and used machinery.

Used woodworking machinery can be an excellent purchase ~ somewhat dependent on the buyers capability in regard to his/her capability and experience in both the operation and maintenance of machinery.

Much of the older equipment has castings of superior quality compared to today's Asian offerings. Unfortunately almost all casting facilities in the USA were shut down due to OSHA and EPA regulations several years ago. Many castings used by machine manufactures in the early 20th century were cast, then aged for a year or more outdoors and allowed to stabilize prior to machining. Machines built using these casting are stable and the machines accurate and vibration free.

That said many, if not most of the machines built during this era were worked very hard for a long time. Some may require major work replacing poured bearings, or worn shafts. If you are experienced in machine repair and alignment they still can be an excellent buy.

New machines (even Asian) do have better safety features in most cases. The bearings are better in most cases, as are some design features such as easier alignment, better dust collection and lighter weight (an advantage if working in a basement shop or where space requires moving equipment regularly). In most cases you will pay much more for a decent quality new machine that works fairly well.

I have mostly new machines however I do have a Powermatic 90 lathe I rebuilt. I purchased two from a school sale that closed their woodworking shop, rebuilt the "best" one and sold the other for more than I paid for it. I also have a Craftsman cast iron Jig saw. I purchased it at a very low cost and it included the pin-less adapter. I had to repair the motor but the saw works very well for my needs.

I looked at used Cabinet saws, and ended up purchasing a new Delta Unisaw (made in Tenn) about 10 years ago. I found it on sale with a special package including Biesemeyer fence, table extensions on both sides and mobile base included. Although used saws were nearly $700 cheaper none had all of the options the new one came with so I would have spent at least $300 for the upgrades.

Unless you have a real need to joint very wide boards (10- 12") the heavy old "aircraft" jointers are not realistic. Unless you have the capabilities to move equipment weighing 1500 to 2000 lbs and experience in evaluating and or replacing poured Babbitt bearings, avoid them! The new Asian (Grizzly etc.) 8" jointers with the spiral (replaceable carbide cutter) heads do a much better job, are far easier to set up and rotating cutters without re-alignment make them a great deal.

Planers are in my opinion much like the joiners. They have the same weight issue, and although the older planers worked well, many do need major work to replace bearings, have gear box wear and may need a bit of work to restore alignment. The best finish from the older straight blades still is not as good as the new spiral heads.

Other equipment should be evaluated in the same manner. Take a realistic look at your requirements. Do you really need to bandsaw 16" thick stock? Older Large band-saws actually (in many cases) have smaller work tables, less effective blade guide methods, poor guarding and dust collection. If you are expecting to re-saw veneer 6" thick by .040, you will realistically need to spend a couple of thousand for a new

European saw or spend serious money and work to adapt an old saw to that capability.

If your needs are limited, used inexpensive machines may be a great way to set up a shop. A used 6" jointer, bench-top planer, older Craftsman table saw, used bench drill press, used bench-top lathe etc. can be used to make most anything with good machine and hand tool skills.

When purchasing any used equipment you should: 1) See it in operation, LISTEN for any unusual vibration that would indicate bad bearings, bent shafts or arbors etc. LOOK at the drive train, make sure the electrical requirements (Voltage, 3 phase/ single phase, amp draw can be met in your shop. INSPECT all castings and parts to visually insure there are no cracks or broken parts (or welded repairs on the castings). Also look at the results ~ does the saw "bog down" when loaded hard (although a dull blade may be the culprit), does the planer or joiner produce a decent finish and is the board straight and does the planer produce a product with a parallel surface? Does a bandsaw "wander" etc. Look for any other potential problems you would consider an issue in your shop.

When purchasing new equipment the biggest advantage you have is listening to the experience of others that own and use the equipment. Wood central users are far more reliable then the "sales brochure" from the company's. Use the internet to search reviews ~ you will certainly find out if there are any major issues with the equipment you are considering purchasing. Compare pricing of similar equipment from vendors, again researching the reviews and asking questions. Your local woodworking club will also be a great asset in determining what will suit your needs, many members would be happy to allow you to inspect their machines and let you try them out.