Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Convert Jorgensen clamp to spreader?

Posts

Convert Jorgensen clamp to spreader?

#1

Convert Jorgensen clamp to spreader?

Wayland

Hi-

I rarely have need of a spreader, and thus don't want to spend the money for one if I'll only use it once every 10 years. But now I need one in the 24" to 36" range. I'm thinking I might be able to grind off the rivets of the stationary head of a Jorgensen bar clamp, which would allow me to turn the two orange pieces around, replacing the rivet with a bolt. But I don't know if the bar will actually slide into the stationary head backwards without binding or otherwise not working. There may also be some other reason why this won't work. Before I make a mess of things, I thought I should bounce the idea off you guys and gals to see if anyone has tried it and if so, whether or not it worked.

BTW, a similar idea won't work with a 3/4" pipe clamp because the handle will hit the pipe and the pipe threads may not go in backward, since they're tapered. The handle would be ok with the 1/2" pipe clamp, but the threads may not work.

Thanks in advance.

Wayland

Re: Convert Jorgensen clamp to spreader?

#2

It involves spending money, but... *LINK*

Bill Houghton, Sebastopol, CA

...the Pony/Adjustable Clamp deep reach pipe clamp reverses for use as a spreader. I've never used one that way, but their website says it works, see linky below and look at the deep reach clamp, bottom left corner (for some reason, it won't link directly to the description of that clamp).


http://www.ponytools.com/index.php/pony/pipe-clamps

Re: Convert Jorgensen clamp to spreader?

#4

Re: It involves spending money, but...

Barry Irby

I have a couple of those. They hang on the rack, lonely and forlorn. There is something about them that is hateful to use. Perhaps if I had a third or fourth arm they might be more loved. The problem is that the "head" (the part with the screw in it) is loose and flops around. If it were possible for a clamp to move into the fourth dimension, this would be there. When you raise it up to put it on something, say two cabinets you are pulling together, the head flops down. It helps if the fixed jaw is screwed on tight so that it does not flop also, but it has a mind of its own. Also, hard to describe, but if as you tighten it, the pads on the jaws are not directly aligned, the whole clamp will twist in a spiral. Not my favorite clamps. I have not tried it as a spreader, but perhaps its most useful function would be to scare off an intruder or to be recycled into something useful.

PS I have lots of pipe clamps and like them well enough.

Re: Convert Jorgensen clamp to spreader?

#5

For Once In 10 Years

Mark Mandell - Gone Round In New Jersey

I'd use a couple of 2x4s and enough carpenter's tapered shims to get the exact distance needed.

Re: Convert Jorgensen clamp to spreader?

#6

Re: It involves spending money, but...

Bruce, a MN Galoot

the short ones are good to use as an extension handle for a tire wrench that comes with new cars that are typically so short they're nearly useless.

Actually I have 4 pipe clamps that work fairly well if you have help to apply them.

Re: Convert Jorgensen clamp to spreader?

#7

PS

Mark Mandell - Gone Round In New Jersey

You're likely to need more than one "spreader" to prevent putting a curve in one or both of the workpieces. Having done a bit of framing, I've had to use both spreaders and clamps to push or pull bowed joists or studs straight. Always takes more than one fixture. As you haven't described (or pictured) your application in detail, I'm only taking a shot here.

Re: Convert Jorgensen clamp to spreader?

#8

Re: PS

Joe Mohnike

You can make one with a nut, all thread, pipe and 2 blocks of wood. Weld the nut on the end of the pipe and screw in all thread. drill a recess in the blocks, one for the pipe and one for the all thread and use as protection pads. Cut pipe and all thread to size needed. This works for me and cheap to make.

Re: Convert Jorgensen clamp to spreader?

#9

Leo Cuellar

Re: Convert Jorgensen clamp to spreader?

Leo Cuellar

I actually did this about a week ago to hold some parts in the right position for welding. The clamp was a Jorgensen #3712-LD. Worked fine.

Re: Convert Jorgensen clamp to spreader?

#10

space permitting, a car jack would too