Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

concave coutout

Posts

concave coutout

#1

concave coutout

Jack Putnam

I am working on a fly reel display the reel is about 6 inches in diameter and I am trying to make the reel as real as possible ( pardon the pun) the problem I am having is the part that is on a fly reel that connects to the bottom of the rod is concave. I am using pine and birch plywood for the display. The piece of wood I am wanting to make concave is pine and is 4 inches long 5/8 inches wide and 6/16 of an inch thick.

I think maybe at this point the wood is too small to work with I should have made this piece when the wood was wider. I was thinking some small sanding drum connected to a dremel tool would do the trick but the small sanding drum (same size as they file dogs toenails) is a little too big. So I am open to ideas I can't think of anything else that would work. Again I think I should have done this with a bigger piece of wood before I cut it done to size. Thanks for any help you can give.

Re: concave coutout

#2

Re: concave coutout

Dick Coers

1)core box bit in the router table

2)cove cut by running at an angle on the table saw

3)carving chisel

4)custom made scratch stock

5)80 grit on a profile sanding block

Re: concave coutout

#3

Re: concave coutout

Bruce, a MN Galoot

if this spot isn't too big, you could always wrap some sandpaper around a dowel and wear it away in time.

Re: concave coutout

#4

Yes, you should have done this first,

Keith Newton

on a longer piece. But if you already have a lot of work on the rest of this part, Maybe you can drill a hole down the end grain of a solid wood piece, then rip it down the middle, leaving two halves. Then rip that leaving a little wood on the bottom. Cut some off the existing part, then glue this newly shaped part on where you cut some off.

Otherwise, you could start over.

But, then you might be able to use two sided carpet tape to hold it onto the side of a longer scrap piece of wood, that would allow you to run it over a 5/8" core box router bit, sticking up through the router table 5/16".

Re: concave coutout

#5

That is what I'd do too...

John in NM

For a one off part it'll take no longer than setting up some kind of machine cut. Use coarse paper to start with, 50 or 80 grit. I have a can of spray on contact adhesive for sticking paper to stuff - works great aside from the spray nozzle getting clogged (I stick in on a can of carb cleaner after using and give it a quick spray).

Other than that, a core box bit in a router table is a pretty straightforward cut. If he's got one the right size already.

Re: concave coutout

#6

Make a Tool

Mark Mandell - Gone Round In New Jersey

Take a piece of 1/8" steel in the width you need to make a round-nosed scraper using your bench grinder (if you have one). Grind the profile you need/want, then grind a bevel for a sharp edge, then use your "blade" like a draw-knife to make your concave section. Shouldn't take many passes in soft pine.

Re: concave coutout

#7

Kneale Brownson

Re: Make a Tool

Kneale Brownson

I'd make the convex version in wood and adhere an abrasive to wear away the concave part.

Re: concave coutout

#8

Re: concave coutout

William Duffield

Maybe I don't understand how this part is shaped, but if it's the curve that fits the cylindrical fly rod, I don't see why you have a problem. I have an oscilating spindle sander with spindles and sleeves from 3" diameter down to 1/4" diameter. One of these should fit your curve and make short work of the part. I also have another alternative, a set of hollows and rounds (wooden planes). One of the round planes should fit the curvature. If your part is sufficiently braced, a concave channel should be easy to make.