Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

made some cutting boards

Posts

made some cutting boards

#1

made some cutting boards

Bill Tindall, E.Tn.

One is going to a woodworker. Given the passion over what to finish a cutting broads with it will be gifted unfinished and he can choose.

The other will be coated in vegie oil of what ever variety is at hand as the board in the middle is treated.

The boards are made by cutting 1 1/16" pieces off the end of 5/4 cherry board. Every 4 consecutive cuts is book matched into a 4 piece block to make the pattern.

Re: made some cutting boards

#2

Re: made some cutting boards

Tom Pilsbury (Chicago)

Very creative. Kinda reminds me of a kaleidoscope

Re: made some cutting boards

#3

Re: made some cutting boards

John Pappas

As I understand it, there is some end grain glue-up in the center. How did you reinforce that joint?

Re: made some cutting boards

#4

no end grain joinery

Bill Tindall, E.Tn.

The face of the cutting board is all end grain. To create a 4 element block, 4- 1" slices are taken off the end of a board about 5" wide. These are turned up on end and arranged consecutively clockwise (or counter clockwise) flipping ever other piece, so that the end of the pieces are book matched.

Re: made some cutting boards

#5

Re: no end grain joinery

John Pappas

Now I got it. Thanks.

Re: made some cutting boards

#6

Jesper, Denmark

Re: made some cutting boards

Jesper, Denmark

I'm curious. What is the purpose of the hole?? Hanging storage?

Re: made some cutting boards

#7

The hole- not obvious till it's used

Bill Tindall, E.Tn.

This style is a product of evolution. It started as just a utilitarian thin board that was placed on the counter to chop stuff for food preparation.

Then I thought it would be better to make something end grain rather than a flat board. Wife needed a gift, and what better gift than something to prepare dinner! I had an ugly piece of ash laying about to test making a board of end grain. I sliced pieces off the end and started to assemble the pieces. The end grain exposure had some dark and light patches. I began to see that I could book match groups of 4 slices into a neat pattern, and did. What was ugly color variation in the flat board became a nicely patterned cutting board.

But it had a practical limitation. When it was slick with fat or oil or wet it was difficult to handle and inconvenient to lift up from a flat surface. I don't remember how the hole inspiration came to pass but it works well even if it looks strange.

Traditionally I made cutting boards from cherry. I found that this style made nice patterns when one edge of the cherry board has some sap. The pattern works good with 8/4 lumber too.


Re: made some cutting boards

#8

Re: made some cutting boards

William Duffield

I have made lots of cutting boards, and I usually put a hole in them. I do this to make it easier to maintain them, by making it easier for the chef to remember to hang them up. If the chef leaves them in the sink or on a wet counter top, or even stands them on end to drain after washing them, they tend to soak up water preferentially through the end grain. After a few cycles of this mistreatment, they are more apt to split, so I give the chef every opportunity to hang them up to allow them to dry more evenly.

It also allows the fancy ones to be displayed more prominently than just shoving them onto the counter next to the toaster or knife block. It can be a sales opportunity, for a board with a row of Shaker pegs. Just make sure the hole in the board is larger than the diameter of the pegs.

Re: made some cutting boards

#9

What glue Bill, given the torture these get?


Re: made some cutting boards

#10

Titebond

Bill Tindall, E.Tn.

I have made many boards with just Titebond and never had a failure when they are properly cared for- damp wipe, never soaked. And I have made a few with Titebond II. I am sure Titebond II is a better choice, but I am not fond of working with it. I have a utility board we butcher on that I made in 1966 that is glued with that resin powder. I have never had a joint failure on any.

Re: made some cutting boards

#11

Contrast of southern and northern cherry

Bill Tindall, E.Tn.

Both boards are oiled with some vegie oil. The top board is made from low elevation TN cherry. The lighter board is made from cherry from central NYS. The color difference is apparent, and typical.

Re: made some cutting boards

#12

Resin powder= Urea Resin

Grant in Iowa

I think Bill is talking about Urea Resin glue, or Urea Resin.

Great stuff, water proof near as I can tell. Dap Weldwood is the major seller, sold under "Dap Weldwood plastic resin".

This stuff comes as a powdered product, looks like cinnamon & sugar, but use it in a ventilated area due to the (I think) Formaldehyde it gives off when curing. Food safe once cured, I was told by tech support when I called them.

I made several water skis with with a bentwood lamination process clamped via vacuum press and had excellent results. Reliability of the joints have been better than anything else I have found. These skis are used in a show ski club, so they see plenty of abuse and water 8 months a year. As far as I know, there's nothing better for a wet environment than perhaps the purple Resorcinol.

The product also resists glue creep, which can be a problem on bentwood projects. And, it is much more resistant to heat than the common variety of epoxies. Our ski team had issues with epoxy glues gelling and failing when stored in a hot environment like an enclosed trailer.

The only drawback I can see is the shelf time is about two years. It won't mix properly, nor bond well much beyond that time frame. So buy what you need and use it up. When storing it, keep it cool. I usually leave it on the floor in its plastic bucket.

Regards,

Grant in Iowa