Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

How would you handle this?

Posts

How would you handle this?

#1

How would you handle this?

Paul Woolson

Help!

I'm working on a project that I'm already upside down on. It's a workout "ladder" that will stand out from a wall. 15 rungs. I wanted to make the rungs really sturdy so I glued them with Poly glue. I wiped up all the excess and left it overnight. Came back this morning to this mess. YUCK!!!

I tried to chisel off the foam but really had problems getting a clean surface. And it took me a good long time to do it that way. I have to do 30 of them. Can anyone think of some sort of system that I could make that would speed this up? (keep in mind that, historically, I've been known take 2 hours to make a jig that saves me 5 minutes of work)

I've thrown away the bottle of glue and will not use it again.

Thanks, Paul


img

Re: How would you handle this?

#2

Prevention is the best cure

Lee Schierer in McKean, PA

There is no easy way to remove the foam once it hardens. It appears you may have dampened the parts before assembly. That makes the polyurethane glue foam. There is enough moisture in the air and in the wood for a proper cure but it will take slightly longer than it does if you moisten the wood. It isn't necessary to moisten the wood when using polyurethane glue.

I usually have a can of lacquer thinner and a rag handy when using this glue and I wipe off any smears or finger prints immediately with a rag soaked in lacquer thinner to avoid trying to remove it later.

You can also mask the area around the glue up with painters tape before you start gluing.

A red devil paint scraper will work better than a chisel.

Lee

Re: How would you handle this?

#3

Re: How would you handle this?

William Duffield

Like a Kunz #75 bull nose shoulder plane, the only thing Gorilla Glue is good for is throwing at feral tomcats.

Being an Anarchist and a Luddite, I would cut a mortise in the rung and put a pair of wedges on both sides of the rails. The ends of the mortise would be tapered to match the taper of the wedges, of course. After I had them fitted, I would tap them in with a hammer, and glue them in place with a spot of the anathema of polyurinate, Old Brown Glue.

On those days that I'm not feeling like being a Luddite, I would cut the mortise with a Festool DF 500 Q and shape the matching Domino tenons with the bandsaw. I'll leave the implementation of the jigs for holding the dowel rungs for mortising and the tenons for tapering as exercises for the curious student.

Re: How would you handle this?

#4

Wax On.  Glue off

Mark Mandell - Gone Round In New Jersey

Paste wac around (not in) the holes and tape on the dowel make removal of the glue quite simple. Then the wax comes off with MS and you're ready for finish

Re: How would you handle this?

#5

A scraper...

John in NM

Either a cabinet scraper or a chisel used as a scraper is what I would do. You may need to carefully re-sand afterward, depending on your intended finish.

Poly glue is useful for what it's useful for, but you do have to be aware of the foaming problem. As Mark says, wax will make glue removal a snap.

Re: How would you handle this?

#6

Re: How would you handle this?

Dick Coers

So you have 60 joints like that to clean up? Wow,I would probably start over.

Re: How would you handle this?

#7

Re: How would you handle this?

Paul Woolson

Actually, it's only 30 (15 dowels) but I'm pretty much in line with your thought process. My only issue is that I'd have to cut them out of their mortises which would shorten the whole thing by 1". Not sure how to fix that.

Re: How would you handle this?

#8

Re: How would you handle this?

Dick Coers

I think it will come apart easier than you think. I've never been impressed with the strength of Gorilla glue. Once it's apart, sanding off the glue shouldn't bee that tough.

Re: How would you handle this?

#9

Turn that SOB into BTU's.

Barry Irby

My first impulse might be suicide, quickly followed by murder. I would kill this one and start over. Actually Dick is probably right. I would try to break the joints with a sharp blow from a heavy hammer on a sacrificial piece of wood ( a beating block). Maybe rack the ladder a bit. I think you can save the rungs, I suspect you will lose the rails.

I did a major project with Gorilla Glue. Never again.

Re: How would you handle this?

#10

Disassembly

Bill Tindall, E.Tn.

Glues that have great toughness, which is to say not brittle, have exceptional shock resistance and less shear resistance. Might try bashing because that is a quick test. But putting the joint under a shear load may be more effective. To that end, put a jack between the joints and apply SLOW steady pressure to force the assembly apart.

Let us know how it works. I have no experience with this material so the above is a hopeful guess.

Plain Titebond would have glued this joint just as effectively and with some heat and steam it would have been reversible.

Re: How would you handle this?

#11

use white gorilla next time not syrup color

del schisler

you used the gorilla glue that is syrup color , that glue foam's and get real hard, once it is dryed nothing brake's it down, the white gorilla glue doesn't foam, i have used it many time's , it is good glue, only thing don't get eather one on your hands it doesn't come off, it ware's off

Re: How would you handle this?

#12

Re: How would you handle this?

Jerry Gibbs

Keep in mind that the workout ladder will become a clothes rack eventually.

Re: How would you handle this?

#13

Re: How would you handle this?

Paul Woolson

I actually told the same thing to my client. She seems to think that she'll use it. (but I made sure the bars are properly sized for coat hangers)

Re: How would you handle this?

#14

Re: Wax On.  Glue off

Paul Woolson

So, if I were to wax around the joint, would that not affect the finish down the road?

I was originally going to use epoxy on this joint since I've got a lot of experience with it. But decided against it thinking that, even if I were to scrub the squeeze-out with lacquer thinner, there would still be a film that would affect finishing.

Re: How would you handle this?

#15

No

Mark Mandell - Gone Round In New Jersey

Wax doesn't penetrate the wood and the MS will remove at and then evaporate. I do this all the time with both PVA and epoxy. Has never failed. :)

Re: How would you handle this?

#16

Re: No

Paul Woolson

Sounds great. Thanks for the tip. Is there a particular reason you would tape the dowel rather than wax it also?

Re: How would you handle this?

#17

Dry Fit

Mark Mandell - Gone Round In New Jersey

the dowel so it bottoms in the hole then, with it in place, wrap the dowel with blue or green tape to make a sharp line to resist the glue squeeze. You can wax the tape as well after you wrap it. Nice neat job and no glue stains to deal with. The MS will also remove any residual tape "stickum" as well. If MS dries too slowly for you, you can also use naphtha as the solvent which evaporate faster.

BTW, I quite using Gorilla et al after glue joints started failing when stressed. They marketed the stuff as gap-filling but the cured foam glue layer proved to be pretty weak, I assume because of the amount of air actually in the joints from the foaming action.

Re: How would you handle this?

#18

Ladder for exercise?

Gary smyth



She don' need no ladder. May I suggest an alternative

Re: How would you handle this?

#19

Re: Disassembly

Barry Irby

Bill may be right (He usually is) about breaking the joints with pressure rather than impact. But, I suspect the Gorilla Glue is different than PVA glue in that it is more brittle. At least I think it is more brittle. I would try both. Set the jack as Bill suggests and then strike it a sharp blow.

The reason its called Gorilla glue is that your hands end up looking like the gorilla's hands. :(

Re: How would you handle this?

#20

more pictures!

Bill Tindall, E.Tn.

I must admit that here in the outback of TN I have no clue what an official exercise ladder is. That said I get plenty of exercise with the ones I have- painting, pruning, roofing etc.