Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

natural cherry wood finishing

Posts

natural cherry wood finishing

#1

natural cherry wood finishing

Herman

I am trying to achieve a natural cherry wood finish that will darken gradually over time. I found a can of Bartley Gel Varnish Clear Satin left over from years ago. Does natural cherry wood continue to darken gradually over time under this finish?

Re: natural cherry wood finishing

#2

Re: natural cherry wood finishing

del schisler

sure does , i make lot's of cherry box's for the craft show , and if you lift the lid's you can see a shadow on the under side of the lid where it closes. unless you put in some sort of uv blocker it will contune to go darker , also if you plane down cherry board's don't put any thing on the wood like another piece smaller than the original or it will leve a imprent on the bottom board, the same if you make a table and it is in a window don't put any thing on it ? of course that is what a table is made for item's , but it will leve that image on the top. i have a cherry table i made and it is by a window but no sun on it, it is a few yrs old and no pattern on it , so i guess after time it wouldn't show ?? dont know how much time tho , the cherry will change slow but will get a nice color to it, check on some uv stuff you put in the finish ? good luck

Re: natural cherry wood finishing

#3

yes

Bill Tindall, E.Tn.

Almost all woods, walnut an exception darken over time. A precoating with linseed oil may hasten darkening process. As always, experiment on a test piece.

As a curiosity, why are you avoiding a stained finish?

Re: natural cherry wood finishing

#4

Re: natural cherry wood finishing

paul in AZ

I love cherry and NEVER stain it. If you want the [stained] IKEA look buy cheaper lumber.

To get the color change a few wipes of boiled linseed oil a day or three apart begins the process and then a couple of days in the sun accelerates it.

Or, left alone the color change will come over months to years depending on how much light it is exposed to.

Finish coat with whatever you like after the oil is well and truly dry.

Re: natural cherry wood finishing

#5

Re: natural cherry wood finishing

John Veerkamp

We just installed a bathroom vanity two weeks ago. It is cherry with just a pre-cat lacquer finish. After this short time there is already a faint shadow line where the doors and drawers overlap the face frame. OTH our cherry kitchen cabinets installed 12 years ago reached their apparent "final shade" in about 7 years.

Re: natural cherry wood finishing

#6

Re: natural cherry wood finishing

Lee Schierer in McKean, PA

I don't like staining cherry either. I use Deft Clear Wood finish in a semigloss and it darkens nicely in a couple months and then a bit more over the first few years.

Lee

Re: natural cherry wood finishing

#7

Ikeas look?  not all there is......

Bill Tindall, E.Tn.




In disparaging stain when finishing cherry it is well to differentiate the difference between what can be done with stain on cherry and an inexperienced application, or an Ikea finishing schedule, if in fact they sell cherry furniture.

People that attempt to stain cherry and fail often do so because they don't know how to properly prepare the surface for staining. And, there are a lot of ugly cherry stains out there. I prefer the mineral based pigment stains. They once were commonly available but now the only reliable source is General Finishes.

Re: natural cherry wood finishing

#8

Re: Ikeas look?  not all there is......

Jerry Roberts

Bill, I like it, I like it!. Im in the process of making a tv credensa from cherry and at first I wasn't going to stain it. I don't have a sprayer but Now id like to do as you suggest. What kind of stuff do I get after the wash coat of shellac and how do I do it? Thanks. Jerry.

Re: natural cherry wood finishing

#9

Re: natural cherry wood finishing

Chuck Jurvelin

I like to have my cherry darken very slightly, but look as natural as possible.

I start with a 50/50 Zinsser sealcote-denatured alcohol wash followed by four to five coats of Watco Natural Cherry Danish Oil. Each coat is sanded in lightly with wet or dry paper from 240 to 600 grit. After plenty of drying time, I apply a coat or two of Watco Satin wax. If the top of the cabinet or table is going to have high use, I skip the wax and give the surface two to three coats of Sherwin-Wms

Hi-build PreCat medium or dull rub finish. This process is a little time consuming, but the finished product is excellent and doesn't look like some plastic or coverup film finish.

Re: natural cherry wood finishing

#10

Another look

Mark Mandell - Gone Round In New Jersey

Cherry and walnut "toned" with Cherry-flavor Watco after a spit coat of 1/2lb shellac for blotch control. Top coated with NC Lacquer.


Picture taken right after finishing so the wood will darken considerably

Re: natural cherry wood finishing

#11

Sorry Bill

Dick Coers

But despite your masterful staining work, that still looks artificial to me.

If using old varnish, make sure to do a sample board to make sure it still dries correctly.

Re: natural cherry wood finishing

#12

Cherry finishing schedule

Bill Tindall, E.Tn.

To me unstained walnut or cherry has a raw informal look to it, suitable for some things and not others. Hence, I stain both walnut and cherry. Some protest that stain "hides the grain". You can be the judge of that from the pictures.

For years I stained cherry from a quart of Sherwin Williams pigment stain purchased in the 70's before they reformulated everything. When that ran out I went on a quest to duplicate this color, a reddish brown. I don't like red cherry and I don't like brown cherry. Goldilocks cherry is just right reddish brown. The result was a mix of 85% General Finishes "Candlelight" which is too brown and 15% ???? that is red. Can't make out the name but it may be cherry. In any case a mix of Candlelight and a red mineral stain or red Japan Color will get one to their preferred reddish brown. Because it is a mineral stain (iron oxides of one sort or another) the color will not fade.

My staining technique has been described here many times and it involves using a "rubber" dipped in stain to control the application density. A quart of stain will last nearly a life time with this technique.

Top coat on bed is shellac. Top coat on table is Sherwin Williams conversion varnish.

Most important is sanding. I sand to 220 on cherry and the sanding must be defect-free. If there are any dull places they indicate torn grain that is catching sanding dust. They will over-absorb stain and go dark.

Re: natural cherry wood finishing

#13

Re: Cherry finishing schedule

Chuck Jurvelin

I agree with Bill...a person will spend countless hours or days producing a piece of furniture and then hurry thru the sanding process and the finishing process to turn a fine piece of workmanship into a second rate project.

Re: natural cherry wood finishing

#14

Duh . . . ?

Mark Mandell - Gone Round In New Jersey

Why do we call it "finish"? The last part of the "project" is the only thing most people will see. It will reveal your screw-ups and hide your mistakes, and be the single most important criteria by which the piece will be judged.

Re: natural cherry wood finishing

#15

One Man's Blotch

Mark Mandell - Gone Round In New Jersey

Is the next guy's figure


:D

Re: natural cherry wood finishing

#16

Amen, a cause to rant against the blotch police

Bill Tindall, E.Tn.

If it is curly maple every effort is made to bring out the figure with dyes, stains and oil. But bring out the figure in cherry and its labeled with the pejorative word "blotch" as in how can I avoid blotch or I stained and got blotch or I don't stain to avoid blotch.

By my definition blotch is where torn grain from inadequate surface preparation absorbs excessive stain. And then there is "figure enhancement" an entirely different phenomena and one to be employed where there is opportunity.

Re: natural cherry wood finishing

#17

Re: natural cherry wood finishing

Herman

Thanks for all the feedback from everyone. I eventually decided to sand to 220 grit and then applied 3 coats of Bartley Gel Varnish Clear Satin without any underlying stain. I allowed 6 hours between coats and rubbed them off each time after a couple of minutes with a clean cloth. The results are spectacular. The natural cherry color will no doubt darken over time. Note that I selected nice lumber and thus did not have to deal with the sap wood issue.

Re: natural cherry wood finishing

#18

Re: natural cherry wood finishing

TomD

If you put it in direct sunlight you may observe it darken around your coffee cup. :)

Re: natural cherry wood finishing

#19

Re: Ikeas look?  not all there is......  Why

TomD

You have achieved a professional looking finish, that I am sure many would be very hungry for, but why do you do it? Stain that is? Are you in a hurry, or are there long term benefits. Cherry can for instance get really dark to the point where the character is lost. And in that piece you have some complexity in the shapes that might not look all that even with a natural finish.

One thing about being a maker is that with the swish of a plane I can reverse the look on some surfaces, right back to the first few hours, and on occasion I have had to. But your piece would be difficult to adjust, and depending on the lacquer, you may not even be able to burn it in.

One of the few places I use stain, is on musical instruments where the materials are dictated, and a little toning can pull together woods that look really awful together in their natural state, or with a finish on them.

Re: natural cherry wood finishing

#20

you answered your own question

Bill Tindall, E.Tn.

You said, "You have achieved a professional looking finish, that I am sure many would be very hungry for". I can not improve on your conclusion.

Unlike an oiled finish my finishing schedule does not darken much after finishing. It looks the way it is going to look upon delivery and it stays that way at least for the few decades I have lived with this furniture.

You have seen the result of the finish I use. If you ever decide to build some cherry furniture you can make an informed decision of what you want to use with the benefit of seeing this example and whatever additional results you have seen. And that is the objective of posting.