Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Air Filtration System

Posts

Air Filtration System

#1

Air Filtration System

Lynn Reedy

I plan to install a air filtration system in my shop.

The plan is to hang it from the ceiling, due to limited

space. I am looking at a Powermatic system but not

locked into it yet. Any experiences with any brand or size

good or bad, would be appreciated..

Thanks for the comments,

Lynn Reedy

Soddy Daisy Tenn.

Re: Air Filtration System

#2

Re: Air Filtration System

Mark Mandell - Gone Round In New Jersey

I use a JDS 750 plus a shop-made 20" box fan-driven filter (you can see it peeking over the drill press here .

SWMBO has observed that the shop may be the cleanest room in the house. Of course, I haven't told her about the Dust Gnomes who come in to polish everything between 2 and 4am. :D

Re: Air Filtration System

#3

Re: Air Filtration System

Henry W

Lynn: I picked up the Powermatic air filtration unit from Craigslist a few months ago - and am very happy with it.

I love the remote, the timer, and best of all, the noticeable cleaner air. At this point it is just sitting on the end to my bench ( hindering my work space? yes it is!) but it is used each time I use power tools. As an added bonus, the air circulation from filtration unit the helps the weak fan on the AC unit - so the air feels cooler more quickly.

Henry

Re: Air Filtration System

#4

Re: Air Filtration System

Howard Acheson

Here is some info that may be helpful.

Here are some general rules based on Nagyszalanczy's "Workshop Dust Control" and some of my own experiences and thoughts.

The two most important criteria for an air cleaner are the CFM and the filters. You want a CFM factor that will clean the size of your shop and a filter that removes the particle size that you are concerned about.

To determine the size or required air flow, use this formula: Volume of your shop (Length x width x Height) times Number of air changes per hour (typically 6 - 8) divided by 60. This will give you an answer in Cubic Feet per Minute which is how air cleaners are measured. MOST AIR CLEANER MANUFACTURERS RATE THE CFM OF THE FAN ONLY, but there are losses due to the filters. If you are building your own or if the air cleaner you are purchasing rates only the fan, figure you will lose about 25 - 40% for filtering losses.

As important as the air cleaner size is how and where you mount it. Try to mount at about 8-10 feet above the floor (no lower than 6'or 2/3 of the floor to ceiling distance if less than 8' ceiling). Mount along the longest wall so the intake is approximately 1/3 the distance from the shorter wall. Mount no further than 4-6 inches from the wall.

The exhaust is the largest determiner of the circulation pattern. You are trying to encourage circulation parallel to the floor/ceiling so ceiling mounting is not recommended. Use a smoke stick (or a cigar) to observe and maximize circulation. Use a secondary fan to direct air to the intake if necessary. Also, consider that a standard 24" floor fan moves a lot of air and, in some shops, just positioning it in a doorway with a window or other door open can accomplish as much or more than an air cleaner. It's all in the circulation patterns.

The exhaust is the clean air so that is where you want to position yourself. Do not place the air cleaner over the a dust producer. That will guarantee that the operator will be in direct line between the dust producer and the air cleaner. The operator wants to be in the clean air stream. If the dust has to pass your nose to get to the air cleaner, you get no benefits. If you have an odd shaped shop, two smaller units may be better than one large one.

DO NOT RELY ON A AIR CLEANER TO ACT AS A DUST COLLECTOR. The purpose of and air cleaner is to keep airborne dust in suspension and reduce airborne dust as quickly as possible AFTER THE DUST PRODUCER HAS BEEN TURNED OFF.

Finally, if you are looking for health benefits, you will not find any air cleaner manufacturer that makes health claims because there are few health benefits. CATCHING DUST AT IT'S SOURCE IS THE BEST LONG TERM GOAL. Rick Peters', author of "Controlling Dust in the Workshop", makes the point that spending your money getting the dust at its source is a better investment than trying to capture it after it is already airborne. If the dust is in the air, it's going to be in your nose and lungs too. Robert Witter of Oneida Air Systems has noted that "overhead cleaners can only lower ambient dust levels AFTER THE SOURCE OF EMISSIONS IS SHUT DOWN, and they take several hours to do this. This is why they are not used in industry." The absolute best answer, if health is the primary concern, is to use a NIOSH approved respirator. The dust cleaner will help keep your shop cleaner but have minimal or no health benefits. OSHA takes this position too. They measure the number of particles per a volume and most air cleaners will not satisfy their specs.

Re: Air Filtration System

#5

Re: Air Filtration System

Pat Evans

I built a portable filtration unit from scrap plywood and a box fan. It has a slot for a high grade pleated filter. Advantages are that I can place it where I need it... opposite whatever I'm working on that produces dust. The air flow pulls dust away from me and into the filter. In conjunction with a built in dust collector that collects the sawdust, my portable filtration unit makes the shop much more user friendly.

Re: Air Filtration System

#6

Re: Air Filtration System

Dave Bair

I've had the JET model for 10 years. It does a good job of quickly cleaning the air. My only beef is that the remote works only in line-of-sight, it's not radio-controlled.

Re: Air Filtration System

#7

Re: Air Filtration System

Alan in Little Washington (NC)

To reiterate and expand on a few points already made and add a few others:

The air cleaner will only filter as well as the effectiveness of the filters you use. If you put cheap furnace filters in it, don't expect good filtering.

An air cleaner only filters the air that passes through it.

Combining the first two points- if you put MERV 16 or HEPA filters on the air cleaner it will do a much better job filter fine dust- BUT, again, it will only filter the air that passes through the filter.

The more effective the filter, the lower the air permeability- lower CFM. The CFM figures for different filter combinations are typically not available, so you may want to start with the highest CFM unit you can find if you plan to upgrade the filters

MERV 16 or HEPA filters in the 12" X 20"-24" size can be 4" thick or thicker and can easily cost $100 each. Like most filters, they can't be reliably cleaned and reused.

Most of the filters that claim they can be cleaned and reused don't filter fine dust well to begin with, and that includes the Gortex fabric pocket filters used in a lot of units. The filter area isn't the greatest either. Years ago Navy ships used filter elements made from steel mesh- kind of like coarse Brillo pads in a frame. Every couple of days, the filters had to be take to the filter shop to be washed in a tank, dried, then sprayed with oil, to improve their already marginal filtering effectiveness.

Many models of shop air cleaners take up quite a bit of head room. The thinnest is probably the Jet with a 12" tall cabinet, but after you add hooks and chains the bottom of the box is now almost two feet from the ceiling - and a real hazard for a typical basement shop.

If the size of the air inlet or outlet is small, just like DC ducting, the resultant CFM will be restricted.

To help keep your shop clean, get an air cleaner, but a good DC will do a better job, and if you have health issues, get a mask.

There may be a new air cleaner design hitting the market next year that does a pretty good job addressing these issues.

Re: Air Filtration System

#8

Cheap effective solution

Bill Tindall, E.Tn.


get a range hood fan from junk store. Mount in box or in ceiling joists. Mine is out of the way in between ceiling joists as shown in picture. Filters are removed for the picture, door is hung open. Mount furnace filter holder. Install a high performance furnace filter with a prefilter made from a piece of polyester batting from fabric store.

Re: Air Filtration System

#9

Re: Cheap effective solution

Barry Irby

The remarkable thing about that picture is how clean the inside is. This was taken right after you installed it and before you ran it, right?

I have made several of these, using the blowers out of old furnaces. I build a box that holds the fan with it open on four sides. Three are on the inlet side and they have filters and the fourth side also has a filter on the outlet side, so the air gets filtered twice. The inlet filters pick up lots of dust, the outlet one, not so much.

Any HVAC contractor should be able to scavenge a blower for you for next to nothing. Get one out of a furnace because it will run on 120 volts. The ones form heat pumps run on 220.

I have one in my shop now and am thinking of adding a second to keep the air swirling.

Re: Air Filtration System

#10

Re: Air Filtration System

Tony - Memphis

I've had the JDS 750 in a 16 x 20 shop with 10' ceilings for many years. Seems to help based on the dirty filters. Been very happy with it and no isues to report.

Tony

Re: Air Filtration System

#11

comments

Bill Tindall, E.Tn.

1. The filter arrangement has been in service for about 10 years.

2. Furnace blowers move too much air at too high velocity for my application. A range hood blower is just right. I expect my more modest air velocity is why I collect nearly every particle and the inside of the enclosure is clean.

Re: Air Filtration System

#12

Re: Cheap effective solution

Gary Smyth

This is my version. 18" x 12" x 12". Two 120v 250 CFM constant speed squirrel cage fans. The pic is the exhaust. The sides are the air intakes and are open frames with 1/2" grid hardware cloth held in place by the aluminum "L" strips. The filter I use is nylon batting purchased from a sewing store 30" wide x 1" thick sold at $5.00 a yard. The inner face of one layer I used to coat with a touch of mineral oil, but I find that overkill. I couldn't find a standard furnace filter that fit tightly at the time so I improvised a filter of layers of batting. (I got the idea from NASA). Air flow is adjusted by the layers of batting (2 works fine)

The filter works great and the material is cheap and the when on the 25' x 25' room stays even small particle free.

There is nothing unusual about the filter, except it's 18 years old. The good part of this is "Surplus Center" (www.surpluscenter.com). If you need blowers, hydraulics, pumps, casters, wheels, lights, motors, capacitors, whole engines, it will be worth while to find the site. The inventory changes daily and categories are added and discarded as the inventory changes, but to builders of STUFF this is a good place to check. The prices are really good.