Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Joining High Density Polyethylene

Posts

Joining High Density Polyethylene

#1

Joining High Density Polyethylene

don stephan

For a customer project I'd like to either screw or glue a narrow cutoff of a high density polyethylene cutting board to itself. I doubt the plastic would hold screws well, is there a common glue that will work?

Re: Joining High Density Polyethylene

#2

Re: Joining High Density Polyethylene

Bill Tindall, E.Tn.

It will hold screws just dandy. With an optimum hole a machine screw does well but you will need a set of number drills. The screws are self tapping.

Takes some sophisticated doings to glue it. As you know, little sticks to it.

Re: Joining High Density Polyethylene

#3

Re: Joining High Density Polyethylene

TomD

They do make psa backed HMWP. You can find all you want to know about glue by looking up attaching it to drift boats.

Re: Joining High Density Polyethylene

#4

In a word

Mark Mandell - Gone Round In New Jersey

No.

HDPE has to be welded using a hot air plasma and then ground smooth. I looked into this for a project. Went so far as to contact a manufacturer. There are a few adhesives that will stick (sort of) but they will not make a structural join. Screws work just fine, but if the item is to be used wet, 308 or better stainless should be used.

Re: Joining High Density Polyethylene

#5

Re: Joining High Density Polyethylene

don stephan

Can't thank everyone enough for very helpful and rapid responses.

Re: Joining High Density Polyethylene

#6

Re: Joining High Density Polyethylene

Lee Schierer in McKean, PA

Loctite has a product that will glue it. You rub on the activator and then apply the glue.

Lee

Re: Joining High Density Polyethylene

#7

Re: Joining High Density Polyethylene

R. Payne

Most plastics are "chemically welded". Which mean the glue dissolves the surface of the two pieces to be joined allowing them to mix, becoming one piece (if everything goes right). I've read of people "welding" high density plastics (no specifics on which ones) with soldering irons or woodburning tools. I don't have any personal experience with melting plastics together.

Before you buy any glue, check that it will work on the HDPE.

Re: Joining High Density Polyethylene

#8

Re: Joining High Density Polyethylene

Alan in Little Washington (NC)

1. No glue will work with any amount of strength with HDPE.

2. Inlike many plastics and acrylics, HDPE will NOT solvent weld.

3. You can melt it together- hard to do so it holds and doesn't look like crap.

4. For any glue to have any chance to bond to HDPE you need to flame it to remove the moisture and give it a textured surface, even so, rule #1 still applies.

Re: Joining High Density Polyethylene

#9

Re: Joining High Density Polyethylene

Barry Irby

There was a TV show that featured a young woman making designer/modern furniture. Can not recall the name of the show. One of the things she made was a set of chairs with metal frames and HDPE seats and backs. At least I think it was HDPE. She had some sort of industrial glue to bond parts together on the plastic to make "pockets" for the metal frame to fit into. I remember being skeptical at the time. Looked like the design was inspired by the Eames'. The woman later appeared on some of the HGTV shows.

Re: Joining High Density Polyethylene

#10

Re: Joining High Density Polyethylene *LINK*

Mark Mandell - Gone Round In New Jersey

Have one. Works.


Plastic welder

Re: Joining High Density Polyethylene

#11

Re: Joining High Density Polyethylene

R. Payne

While I haven't use any, I've seen two or three adhesives say on their labels that they work on HDPE (and one, TAP I think, claiming structural strengths). As I said, I haven't had a chance to try any but chemistry ever moves forward and I would be surprise if someone managed to formulate something that works.

ron

Re: Joining High Density Polyethylene

#12

Re: Joining High Density Polyethylene

Larry Clinton At Frankfort, (Central) Indiana

As an Engineer in an Industry that used a lot of HMWP, I have never heard of or seen any bonding material that has any structural strength.

We had Aqueous Cleaners (large machines made to clean circuit boards) that were constructed with the material. Nothing other than mechanical fasteners, or in the case of watertight seam "hot welding" was used in either the construction or maintenance of this equipment. One of the great advantages of this material is the fact it is extremely low friction - nothing sticks to it, the second advantage is that it is very resistant to solvents. These characteristics tend to make it a material that does not suit to bonding by any adhesive or solvent welding.

Re: Joining High Density Polyethylene

#13

Re: Joining High Density Polyethylene

Jay Lombardo

I have never had any luck getting anything to stick to HDPE, worked a lot on underground storage tank systems with all kinds of poly sumps and fittings, etc. But that being said, last month I repaired the poly tank of my sand pool filter with a product that worked very well. Mr. Sticky's Poly-Bonder. As mentioned here already it required heating the surfaces to be bonded with a torch and the instructions were VERY specific about what had to be done, not difficult but very step by step. It's been a month now and no leaks at all. I found it online but needed to make repairs that day, so I called the company and they pointed me to a boat marine store near me that they manufacture the stuff for under their label. Cost me $10 more but its the same stuff. Repair is holding up under pressure of the pump so far. Good Luck