Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

A Custom-made Brass Door Pull

Posts

A Custom-made Brass Door Pull

#1

Alan Young

A Custom-made Brass Door Pull

Alan Young

I am working on a Sheet Music Cabinet. This piece is a commission from a friend from college days. He already commissioned two earlier music cabinets for graduation gifts for two daughters. This third cabinet is for his last daughter's college graduation.


I made a Brass Pull in the form of a combination G and F Clef. Here are pictures of the process. I made this pull by first drawing the design, then fixing it to a piece of brass with double sided tape. The brass is then clamped in a milling machine vise.


I milled a 1/2 diameter recess with an end mill.


I replaced the 1/2" end mill with a counter sink and drilled a hole for an 8-32 screw that will fix the Double Cleff Pull to the rest of the piece.


I replaced the counter sink with a smaller end mill and mill out the interior sections of the profile.


Once the interior lines are milled out, I take the work piece to the band saw and cut away the rest of the profile.



From this point onward it's all file-file file!




Now to the lathe where three different sized hex pieces are drilled and turned for the remaining sections of the mounting hardware.


One end of the 1/2" hex is tapped for the 8-32 screw. The other end is tapped for a 1/4-20 screw.


The 1/4-20 goes through two 1-1/8th hex pieces and one 3/4" hex piece. The door section will be between the two larger pieces.





Here is the cabinet as work-in-progress....


Re: A Custom-made Brass Door Pull

#2

question

Bill Tindall, E.Tn.

Band saw picture- there is a slotted piece of metal to left. Is it part of the sawing process?

The word elegant came to mind upon seeing the cabinet. Love the design.

Re: A Custom-made Brass Door Pull

#3

Alan Young

The Slotted Piece--

Alan Young

Yes Bill-I was using the aluminium piece ( from a project at work)with my left hand to guide the cuts-notice the jaws of the vise grip holding the other end--I would have a difficult time pulling off this piece without access to the machine shop.....

Glad you like the design-a bit of refining still to go on it but it must be ready in a week as I am taking it with me for delivery.

-Alan

Re: A Custom-made Brass Door Pull

#4

Wow!

Tony - Memphis

That is really nice!

Tony

Re: A Custom-made Brass Door Pull

#5

Re: 2nd that - Wow !


Re: A Custom-made Brass Door Pull

#6

Ellis Walentine

Unique!

Ellis Walentine

...and very imaginative. Getting beyond wood as the only medium. Love it.

Great work, Alan!

Ellis

Re: A Custom-made Brass Door Pull

#7

Re: A Custom-made Brass Door Pull

Keith Newton

Alan, was that your only choice for bandsaw blades? It looks to me that you should have been able to cut a lot closer to the line than that. I think I would have been able to cut just outside those long sweeps, with my wood-cutting blades, with a whole lot less filing.

One thing I do when cutting metal like this, is to put a scrap of 3/4 mdf or plywood, which I cut out into the middle of, leaving it there as a zero clearance raised bed. This takes care of any chatter possibilities around the opening toward those thin ends, plus gives my hands a better grip, where it overhangs that sub-base. But you probably like filing more than I do. ha

Oh by the way, where did you get the metal, and how much does it cost per sq. ft.? I was over at my local salvage yard yesterday, and spotted 4 pieces of 1/2" x 6" X 12". I should have picked them up, but had already settled up with them. I have a project in mind where I would make a pair of fluted elliptical columns which could open up to reveal drink bar bottles and glasses etc. inside.

Re: A Custom-made Brass Door Pull

#8

Alan Young

Re: A Custom-made Brass Door Pull

Alan Young

Alan, was that your only choice for bandsaw blades?

no...I could have replaced it with a narrower blade ..didn't seem to be an issue at the time..

One thing I do when cutting metal like this, is to put a scrap of 3/4 mdf or plywood, which I cut out into the middle of, leaving it there as a zero clearance raised bed.



Good idea---not much MDF available in this shop

Oh by the way, where did you get the metal, and how much does it cost per sq. ft.? I was over at my local salvage yard yesterday, and spotted 4 pieces of 1/2" x 6" X 12". I should have picked them up, but had already settled up with them. I have a project in mind where I would make a pair of fluted elliptical columns which could open up to reveal drink bar bottles and glasses etc. inside.

There is an Alro store here.(Ann Arbor) I cut this from a piece of brass-1/4" x 1 1/4" x 12". That piece plus an 18" long 1/2 hex bar ran me $25.00....