Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Looong T-bolts and drilling paper - help!

Posts

Looong T-bolts and drilling paper - help!

#1

Looong T-bolts and drilling paper - help!

Craig Daymon

I ran into a problem today working on a gift for my niece. I've written a computer program that takes a video, allows you to select a clip from the video and generates a flip book to be printed of the clip.

I printed out the images, stacked them all up and tried to drill through the stack so that I could insert Chicago bolts (or whatever their other name is) to hold the stack together. When I drilled the first hole, the paper climbed the bit and the stack became much thicker in that side due to fraying of each sheet.

I realize I need a better way of clamping the stack before drilling in order to do this correctly. I am using a brad point bit. I have 2 T-tracks in my drillpress table and if I had longer T-bolts, maybe 6"(?), I could drill holes in a strip of wood same distance apart as the T-track and use the wood to clamp the paper in place and, if necessary, drill right through the wood and through the paper.

Anyone know where I can find T-bolts of that length that will fit standard mini T-track? (3/4" wide, 3/8" thick T-track)

Or if anyone knows a better approach to cleanly drilling a stack of paper, I really appreciate some help.

Thanks.

Oh yeah, there are 2 small strips of jatoba involved in this to dress it up a bit, so there is some woodworking.

Re: Looong T-bolts and drilling paper - help!

#2

Clamp

Mark Mandell - Gone Round In New Jersey

it between two pieces of plywood and drill through everything

Re: Looong T-bolts and drilling paper - help!

#3

Re: Looong T-bolts and drilling paper - help!

Dick Coers

I've used carriage bolts and ground the sides off the head for long T bolts. For drilling paper, don't use a fluted bit. Get a piece of thin wall steel tubing, and grind the inside diameter with a cone stone in a drill or Dremel. Hone the burr off the outside diameter to get the final sharp edge. The core will fill up with the paper "holes", so be prepared to take it out of the drill press and poke them out with a stiff wire or awl. Watch out, it will really get HOT! You might also look into an adjustable hole punch.

Re: Looong T-bolts and drilling paper - help!

#4

what I did

Bill Tindall, E.Tn.

One summer I had a job of assembling a lab book from 50 or so Xeroxed pages. It was about 3/4 inch thick. I had a drill template (piece of wood)with the hole spacing. I put the collated sheets in a frame to align them along the top an edge, placed the template over the stack, pressed it down by hand pressure and drilled a 1/4" hole with a normal twist drill mounted in a hand held drill. Then I put the assembly into a cover.

An easier approach is to by printer paper with the holes already punched

Re: Looong T-bolts and drilling paper - help!

#5

Re: Looong T-bolts and drilling paper - help!

Robby Wright - San Marcos, CA

You can use regular hex head 1/4" or 5/16" bolts with most T-track. Both are available in long lengths. You can also cut a piece of all-thread to the length you need and add a nut on one end for the T-track. Clamp the paper between a couple of scraps and drill through the scraps and paper - you should get a good hole that way.

Re: Looong T-bolts and drilling paper - help!

#6

Rick L

Re: Paper drill bits

Rick L

You do realize that there are special bits for drilling paper!

Re: Looong T-bolts and drilling paper - help!

#7

Re: Paper drill bits

Craig Daymon

I did not. Thank you.

Re: Looong T-bolts and drilling paper - help!

#8

huh, looks like sharpened tubes...

Dick Coers

I wonder who said that?

Re: Looong T-bolts and drilling paper - help!

#9

Re: huh, looks like sharpened tubes...

Craig Daymon

They do and I can't see spending $30+ per bit for these. I should be able to accomplish it with brad points as long as I clamp the stack down tightly between strips of wood.