Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Board and batten shed/painting???

Posts

Board and batten shed/painting???

#1

Board and batten shed/painting???

Tom Dunlap

There's a good chance that I'm going to build a small storage shed about 8x10.

Since I'm an arborist and I have access to logs my plan is to make it out of green wood and let it dry in situ. We're going to be taking lots of ash trees down. I like working with ash and I know that it's not very rot resistant. That's not a concern, I don't expect this shed to last for years and years.

The plan I'm thinking of would be to frame the shed then use 6-8" boards for board/board or rip some into battens for board/batten siding.

I'll use ash, or whatever wood, for the framing too.

The question I have regards painting the shed. Adding a layer of paint will help preserve the wood. should I prime the green wood before building? Let it dry until fall maybe then paint it inside and out? Or should I let it dry as a shed and paint it later on? I can't wait to use air-dryed lumber so the shed will HAVE to go up green no matter what.

Thanks,

Tom

Re: Board and batten shed/painting???

#2

Re: Board and batten shed/painting???

Dick Coers

Two problems with coating wet wood. Water of course, but also wood shrinkage. Doubt if anything will stick to the wet wood. You may also open yourself up to a little powder post beetle damage as well. Ash is like candy to them, especially wet ash sapwood. Just thinking out loud because I have no direct experience. I did frame a shed roof extension to my garage with pine that I milled, but that wood sat over a year before I used it. I also used reverse board and batten plywood for siding.

Re: Board and batten shed/painting???

#3

Start

Mark Mandell - Gone Round In New Jersey

with "Seasonite". It's made to control drying of PT lumber and will control moisture loss. Leave the interior uncoated. Wait 2 months than apply Cabot's "Problem Solver" to the exterior. Wait 2 more months and apply your exterior stain/sealer/paint/what-have-you.

Extra Suggestion: Instead of Board & Batten, use 1" ship-lap joints set tight to begin the drying. Apply your battens next year after your siding has "weathered in"

Re: Board and batten shed/painting???

#4

Re: Board and batten nailing patterns

Tom Dunlap

Here's som info I found about nailing patterns that accommodate drying.

http://www.finehomebuilding.com/item/29146/how-to-install-board-and-batten-siding?&lookup=auto&V27=&V28=&V29=&V30=&V31=&V32=&V33=&V34=&V35=&V55=&V56=&Taun_Per_Flag=True&utm_source=email&utm_medium=eletter&utm_content=fhb_eletter&utm_campaign=fine-homebuilding-eletter

Re: Board and batten shed/painting???

#5

Clint Searl

Re: Board and batten shed/painting???

Clint Searl

I'd be inclined to run horizontal purlins on the open framing, to which the boards and battens would be center nailed with "Maze" nails, finished green with a couple coats of Behr waterborne solid stain.

Re: Board and batten shed/painting???

#6

Don't do board/board

Bill Houghton, Sebastopol, CA

Board and battern - boards nailed in the middle with slight gaps between, and the battens nailed so that the nails go through the gaps - will accommodate the shrinkage best.

Mark sounds like he's got a good idea on the treatment while you wait for the wood to dry.

Re: Board and batten shed/painting???

#7

Re: Don't do board/board

Barry Irby

I like the horizontal purlin idea. Got to have something to nail to.

I would suggest making some sort of tray and standing the boards and battens in it and soaking the bottom ends with preservative. I soaked a number of porch columns this way about twenty five years ago and they are still sound. Would have expected them to rot in five years or less. I used BoraCare.

I would either use either a single nail or screw in the center of each board or The pattern shown with a nail at one edge and the other held be the batten. Use heavily galvanized nails or deck screws.

Consumer reports just had a piece on TV about stains. They recommended a Benjamin Moore product Called Arbor......something at about $48 a gallon. Their second choice was a Behr product at less than $30.

I would soak the ends, let the wood dry in place, and then stain it in the dry season. In the dry season, the boards are the most shrunken/exposed. If you stain in the wet season, when the boards dry again, you will have exposed stripes. DAMHIKT Come to think of it, If I could muster the patience, I would install the boards and save the battens. Later I would stain the building and the battens separately and then install them.

Re: Board and batten shed/painting???

#8

Re: Don't do board/board

Basil

I used 1" x 6" white oak with 2" battens to build 12' x 12' shed 20 years ago....all green as grass lumber. Left 1/2" crack between boards, big mistake, when it shrink the boards were from 1" to 1 1/2" apart barely covered by the 2" battens. Doesn't leak but do wish they were a little closer together.

Do as suggested, jam boards together, with one nail in center of board, then put nails in batten at the right distance apart with say 1/2" protruding through it so you can place nail right in the crack. Wait a couple of months, tighten up the nails, then paint. I used Behr wood preserver with a UV screen and the shed looked really good for almost 10 years.