Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

How do I adjust my jointer knives?

Posts

How do I adjust my jointer knives?

#1

How do I adjust my jointer knives?

Joe in a Cleveland suburb

I just had the knives sharpened for my 6" Delta jointer.

I don't understand from the manual how to adjust them. It's not written very clearly (for me anyway).

I think what the manual is saying is to adjust the outfeed table to .060" above the roller, then use a straight edge (steel ruler) on the outfeed table and adjust the knife height until it just touches the ruler at TDC.

I've watched some videos and read some sites about using a jig with magnets at TDC, but how do you know the roller is at TDC?

Maybe I am trying to over complicate it...

Thanks.

Re: How do I adjust my jointer knives?

#2

Re: How do I adjust my jointer knives?

Barry Irby

I also have a 6" Delta jointer that is old enough that it does not have any of the newer features to assist in setting the knives. My understanding is that the newer ones have jack screws under the knives that you adjust up and down to get them "just right". Before I ground mine down too far, I could drop them into the slots, letting them bottom and then tighten them into place. Once they were too narrow for that, I got tired of trying to fiddle them into place. What I have been doing lately is to use a spacer under the knives. I pick two allen wrenches the same size (about 1/8" maybe) and put one under each end and snug the knife into place, doing all three the same way. Then I adjust the outfeed table using a steel rule. I set the role on the table and lower it until the knife just snicks on both ends. With the jointer unplugged, I turn the head by hand so that each knife touches the steel rule at each end. You want all three knives to be identical in height compared to the outfeed table. If you have a high knife, it does most of the work and will leave the edge of the board scalloped. If this does not work well, IE you have a high or low knife, you can tweak that one. Raising one is easy, just twist the allen wrench under the low end or use the next larger wrench as a spacer. Clear as mud????

Re: How do I adjust my jointer knives?

#3

Re: How do I adjust my jointer knives?

John in NM

The funny part is that a shop I worked for years ago had gotten rid of those old school screw jacks and installed springs in their place :D My old planer has the jacks and I do like them a bit better.

However, springs are fast. I'm guessing that your unit doesn't have holes for either?

My older 8" Rockwell has springs IIRC, but I still use hardwood 1x sticks with rare earth magnets let in (3 in each). The middle one and one of the end ones hold the sticks to the outfeed table, the other end one holds the knife up (mostly) if you don't have springs in the head. The RE magnets are usually strong enough to hold the knife even by the edge. Some care should be taken to avoid dinging the blade, but that's not too challenging.

I just eyeball TDC, to answer one of Joe's questions.

Re: How do I adjust my jointer knives?

#4

The rule drag method (simple, effective)

Grant in Iowa

Joe,

Unplug stuff, don't cut yourself, don't do this drunk, yadayadayada:

I am a former machinist, so I like to work in thousandths, but this is a too-easy way to get the job done efficiently without the fancy measuring tools that require bifocals these days:

First, you need a steel rule that will stand on its edge by itself. I have an old craftsman rule from a combination square that works well for this procedure. I did "lap" the edges on mine slightly to allow it to stand nicely on its edge. Decide on an edge and an end and mark it with a sharpie so you use the same edge and side each time you do the ruler drag procedure below.

Install the fresh knives in to the jointer and snug them *almost* tight, yet loose enough that the jack screws can move them. Next, mark each knife with your sharpie by putting a 1,2,3 on the cutter head to ease confusion.

Now, make two marks on your outfeed table at the very edge where it overhangs the cutter head. Make each mark near the jack screws, yet allowing access to the jack screws for adjustment purposes. These marks will be where you place your rule laterally.

Now, stand your steel rule on edge such that the 3" mark (or any specific spot really) is exactly on the edge of the outfeed table, with the first 3" overhanging the cutter head. Don't forget to use the edge and end of the rule we talked about above! Lets start on the mark described in the paragraph above nearest the fence. Then rotate by hand the cutter knife labeled "1" so the arc of the knife goes past the overhanging ruler towards the infeed table. If no contact between the ruler and cutter knife is made as it passes, raise the jack screw associated with that end of the #1 knife. Move the ruler to the same 3" location over the other mark you made on the outfeed table and repeat the cutter rotating procedure, adjusting the jack screw upwards until it just makes contact with the ruler as it goes by.

Now, here's the cool part. Once you have the knives in the butter zone, they will each begin "dragging" the ruler a tiny bit as they go by. This tiny amount of drag is what we'll measure knife height with. The math doesn't matter, just know you want them all to drag your ruler about 1/8" from the 3" mark. Always return your ruler to the 3" mark each time you do a knife "fly-by".

Your mileage may vary, but for me, in my shop, with my pseudo calibrated steel rule, and for my particular jointer technique, I find that about a 1/8" ruler drag results in good jointing results. Sure there'll be some purist mathematician engineer type who will interject something about how it is all wrong. He'll undoubtedly use words like Pi, tangential, radii, and other egg headed words. Let me just respond right here and now that if you do this and set each cutter knife so it drags your steel rule about 1/8", you will be reeeeally close to being right on the money. Get your dial caliper out if you doubt me (I did...once, then I put it away and do it this way every time). What results is jointing bliss.

Obviously, you repeat this process with each knife, then check them all once more after you tighten the retainer bolts, then wash rinse repeat until the coveted 1/8" ruler drag is reached when they are tight and you'll be happy. Never again will you dread jointer knife changes, nor covet other men's jointer knife jigs, nor will you waste precious resources on a mag-O-matic setting jig that you could have spent on a good steel rule that has so many other uses.

"But Grant", you say. "It seems like your technique will result in knives that are higher than your outfeed table". Correct you are. They have to be. Consider that a jointed board has a bunch of tiny little arcs cut in it like waves on an elven ocean. Just look real close and you will see them for yourself. The height of these waves is determined by two things: height of jointer knives and feed speed. So, if you can maintain a steady feed speed equal to mine, and you set the knives like I did, you get good results. This is because the knives are set to eeeever so slightly higher than the difference between the wave peaks and valleys. Make sense? How fast do I feed? I do lots of face jointing, and I would guess that I feed about 2 or 3 inches per second, but I never tried to measured it. A 20" board takes me around 10 or so seconds to feed though.

It is really much simpler in real life than it is in text. I promise. If confusion ensues, I trust someone will google up a video of the process, which will make it all crystal clear.

Regards,

Grant in Iowa

Re: How do I adjust my jointer knives?

#5

another opinion

Bill Tindall, E.Tn.

Presuming the jointer has an adjustable outfeed table it matters not how much the ruler moves so long as all points on all knives move it the same amount. Then adjust the outfeed table until there is no snipe, yet the board feeds without hitting the outfeed table.

BTW, I find that a hardwood stick works fine. The knife sticks in the stick better than the steel ruler.

Re: How do I adjust my jointer knives?

#6

Re: The rule drag method (simple, effective)

Barry Irby

Much better and more lucid than my description above, but the same thing.

Once the knives are set so that all three are an identical height above (or below) And parallel left to right to the out feed table, you can tweak the height o the table to get the feed right.

Re: How do I adjust my jointer knives?

#7

Re: How do I adjust my jointer knives?

TomD

I use magnetic tool hangers, they clamp really hard to the jointer, and I put a witness mark near top dead center. The knives hang from the magnets, at the witness mark, and the head is tightened down. The machine I have doesn't have any adjusters or supports for the blade. Obviously my approach is a variation to that commercial jig. It is also a very easy jig to make in a world of rare earth magnets.

As with other replies I adjust the outfeed, but it doesn't have anything to do with snipe. It is the control for ensuring that the cut is straight. Or to be correct, it controls spring (hollow or convexity, the length of the board). The drag the knife thing could be used to determine the parallelism of the knife to the center of rotation, but it is actually a test to get a range for the outfeed table height. Saves some set-up time.

One method for determining TDC is to use a dial indicator. I have a holder that Oneway makes for such things, but you can use most bases with magnet tension dialled all the way down till it is easy to move. Of just screw an indicator to a block of wood you can get a workable indicator for about 6.95, better ones can go way up in price, but occasionally they topple so I keep some of each around.

You just raise the knife until the indicator tells you it is as high as it will go. Then you use a wedge to hold the head there. Then when you switch out the knife you can make sure it returns to the same zero. There are methods of building a jig to index the knife to TDC, if anyone wants to know.

Re: How do I adjust my jointer knives?

#8

Bill's right, and...

Grant in Iowa

Bill is correct in saying that the 1/8" thing is not critical when setting the knives, and is really probably only useful for me, my jointer, feed rate and technique to quickly get me back working again. I still think it is a good place to start, and the user can adjust as they see fit once they have experience with the process.

I should also add that as the knives wear, they become "shorter", and therefore a tendency for the jointer to create a slightly convex edge creeps in. Being adept at knowing what to look for and knowing which way to adjust things is crucial to easily making adjustments.

Assuming good technique:

If the edge you are jointing comes out convex, then the out feed table is slightly too high.

If the edge you are jointing comes out concave, then the out feed table is too low.

If the work piece hits the out feed table as it is fed in, then either the work piece is badly out of straight to begin with, or the out feed table is too high.

If the work piece has snipe on its trailing edge, then the out feed table is too low.

If you are having trouble with a conflict between two of the above situations, it may be your technique, or as said above your work piece is badly out of straight to begin with. In the latter case, you can reverse the work piece, adjust the infeed to take a different cut, or joint the opposite edge, then straight line the offending edge at the table saw. You can also do stopped cuts or partial cuts with the jointer, but that requires practice and great care to do safely. The technique for which is beyond the scope of text.

Thanks for keeping me honest as always, Bill!

Regards,

Grant in Iowa

Re: How do I adjust my jointer knives?

#9

I tend to shoot for 1/8" too...

John in NM

I was too lazy to write it all up and keep it clear. Hat's off to you for taking the time :D

That takes a lot of effort, writing out something that is typically demonstrated and explained verbally - that's how I learned it :D

But I too find that if the drag is around 1/8" no further adjustment is needed.

Another trick is to give the bevel of each blade a swipe with a sharpie and then once the blades are set joint a piece of wood. Turn off the jointer and inspect each blade - if any are cutting deeper than the others, more of the ink will be worn off.

Re: How do I adjust my jointer knives?

#10

agree

Bill Tindall, E.Tn.

It was an outstanding explanation, worthy of write up for Articles. I'll get right on it.

Re: How do I adjust my jointer knives?

#11

Re: agree

Grant in Iowa

Bill,

Please include the corrections and comments. I think doing that helps make for a nice finished product.

Thanks as always for the input. I would be willing to take some photos and send them along for inclusion, if it would help make the explanation better. Drop me an email with the address to send the files and I will get on it.

Regards,

Grant in Iowa

Re: How do I adjust my jointer knives?

#12

Thank you.


Re: How do I adjust my jointer knives?

#13

Re: How do I adjust my jointer knives?

Jesse Cloud

The tech who maintained the machinery at the woodworking school I used to attend had a nice variation on the drag method.

She had a maple board a couple of inches tall, a couple wide and maybe a foot long. She had a series of lines that went up vertically at a right angle to the bottom of the board. Each line was a different color. Each line was about 1/8th apart.

She would start with the first line positioned at TDC, which she scribed on the fence of each jointer. Then turn the cutter to drag the board. Then she would see which line remained at TDC. If the second line was on TDC she was done. If a different line was there, it would tell her how far off she was. She could set up a jointer very quickly.