Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Rubbing out Poly finish?

Posts

Rubbing out Poly finish?

#1

Rubbing out Poly finish?

Barry Irby

I made a QSWO table for a friend. Tried to pull out all the stops. Tapered the legs and veneered the faces that did not have rays. Used a piece of crotch wood for drawer fronts and resawed it so they are book matched. Made pulls out of the crotch wood. He wanted it finished with Urethane with a satin gloss. Its been finished for about three weeks.

Is that long enough to dry it and let it cure before rubbing it out? I have paraffin oil and pumice and Rotten stone. Can somebody remind me of the order of events?

Re: Rubbing out Poly finish?

#2

Unanswerable question

Bill Tindall, E.Tn.

Is it ready? well, sand it and see. depends on formulation, humidity and temperature. Two days at summer temperature would be adequate.

Procedure- wet sand smooth, pumice, rottenstone. The result will be a mirror if the finish formulation enables rub out. (all urethane varnish is not created equal)

If you just want a satin finish rub with 4/0 wool and wax. Fact: the duller the finish the less figure will show up.

I always recommend experimenting on the final piece of furniture. Preparing a test piece while finishing the piece of furniture is a lot of extra work and so is experimenting and practicing on the test piece. So much effort has gone into the furniture piece there just isn't any left for a test panel. Much better to assume all will go as expected and just have at it. This strategy has been known to work occasionally. And if it doesn't ask on WC how to fix the problem. Stripper is cheap. :D

Re: Rubbing out Poly finish?

#3

Depends

Mark Mandell - Gone Round In New Jersey

on what you want for a final surface. Here's why

Oil finishes (poly being one) will continue to "shrink" down onto the surface over time as part of the curing process. What may start out as a 7-9 mil coating can easily wind up as 3 mills of a much more dense film. What you will get as a final surface depends on how you have finished and how long you wait to rub it out.

Case in point is this walnut sideboy


Before I knew/learned better, I attempted to do a filled-pore (piano) finish with 18 coats of poly, each carefully sanded level before the next. I waited about 3 weeks and then started the rub-out. I got a beautiful glass-like finish.

It didn't stay that way however. As the finish continued to cure and shrink, the wood's open pores, filled only with poly, began to show. We decided to leave it as is because the very slight grain and faint joint lines actually enhanced the appearance.

From my experience, if you haven't used an actual pore filler on your Oak, I would either wait a good 3 months before doing your final rub-out or do it now to establish the sheen and then allow the grain to reappear. The risk in waiting is that the bottom of the pores will remain shiny as you "satinate" the surface.

Re: Rubbing out Poly finish?

#4

Clint Searl

Re: Rubbing out Poly finish?

Clint Searl

Just wet sand to 600 with soapy water to flatten the poly. It'll probably be what he wants.

Re: Rubbing out Poly finish?

#5

good plan

Bill Tindall, E.Tn.

Don't forget to use wet/dry paper. That is where I start, but it is pretty dull if you don't rub it some brighter.

Re: Rubbing out Poly finish?

#6

Clint Searl

Re: good plan

Clint Searl

For a higher sheen, rub it out with auto polishing compound. The key is to start with a leveled finish.

Re: Rubbing out Poly finish?

#7

False

Joe in a Cleveland suburb

"Stripper is cheap. :D"

That's not true. About 30 years ago my brothers hired a stripper for my bachelor party. They said it wasn't cheap...

:D

Sorry. I'll leave now.