Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Re-sizing bandsaw blades

Posts

Re-sizing bandsaw blades

#1

Re-sizing bandsaw blades

Paul Woolson

I purchased two resaw blades that were the wrong size. I called the company who promptly sent me the proper size but didn't want the wrong ones back. I already boxed them up and was ready to ship them. Well, they've sat in that box for two years and I'm finally coming to terms with the fact that I either need to do something with them or scrap them for recycling.

Does anyone have a source for having them cut and resized? (I've thought about doing them myself but am not sure I could get them perfectly straight.)

thanks, Paul

Re: Re-sizing bandsaw blades

#2

Re: Re-sizing bandsaw blades

Bill Tindall, E.Tn.

Everywhere has a place that makes up band saw blades from coil stock. Check with any metal or wood working shop in you area.

Re: Re-sizing bandsaw blades

#3

Re: Re-sizing bandsaw blades

John in NM

As Bill said, anywhere that sharpens blades will probably also have a blade welder. Some machine shops have them too, but that may be a bit old school for the typical CNC shop.

I've also had good luck soldering them with silver brazing wire. You can do it with a propane torch if patient, but an air/acetylene torch works better.

Cutting them is easy, just use two crescent wrenches and twist.

Re: Re-sizing bandsaw blades

#4

Re: Re-sizing bandsaw blades

Dick Coers

Whoa, you're suggesting he take two adjustable wrenches and twist break the blade so he can silver solder it back together? How would he get two flat straight edges for the clean joint? Aviation snips have cut all bandsaw blade stock I have ever used. I use a disc sander to then square them up, and then angle the faces for a skive joint. A silver solder joint needs to be really accurate and tight for strength.

Re: Re-sizing bandsaw blades

#5

Snips work too

John in NM

Though when I've suggested those, people jump all over it saying the relatively hard blade dulls them quickly. Can't win :D

Nothing wrong with the two wrench method, the twist is minor, easy to remove with any grinding/filing method you prefer.

Re: Re-sizing bandsaw blades

#6

Re: Re-sizing bandsaw blades

Paul Woolson

Now that I think about it, since these were essentially free, I've got nothing to lose. Maybe I'll try this myself. Would brass brazing work or is there something specific about solder that would make it better? I've got welding torches and some experience with brazing. my only concern is making sure there isn't a bump or offset in it when I'm done.

but, again, what do I have to lose?

Thanks, PW

Re: Re-sizing bandsaw blades

#7

loose?

Bill Tindall, E.Tn.

about $25 worth of blades that a shop that welds blades would do for $5. Or try it and cut them long. If it fails then go to shop. Normally saws have 1 1/2" of blade length tolerance.

Re: Re-sizing bandsaw blades

#8

Re: Re-sizing bandsaw blades

Dick Coers

It just about the heat. Any alloy that melts above 750 degrees is considered hard soldering or brazing. Silver solder will melt starting at around 1150 depending on alloy. Brazing rod melts around 1600 depending on alloy. The most important part of the success of using these is flux. Second most important is the angles ground on the faces of the blade in the joint so you have more joint length and it is not a butt joint. I put on lots of flux, cut a short piece of silver solder and then place it right on top of the flux on the joint. I bring in the heat from the back. The flux melts, then the silver solder flows in. When cool, I use a sanding drum in a Dremel to sand the silver solder flush. I routinely silver solder 3/4" resaw blades for my Minimax S45. Never had one break on a silver solder joint, have had several break on a welded joint.

Re: Re-sizing bandsaw blades

#9

Re: Re-sizing bandsaw blades

TomD

Safety silv flux and solder is good stuff. I buy the flux locally but often get the solder off ebay. Be careful not to get the stuff with Cadmium in it (safety silv doesn't have it, that is the safety part) Though for rare use it probably doesn't mater much. Another option if you deal with brownells is silver solder tape, it is a ribbon of material designed to fit under sights, and ribs on guns. It is great where you want to use less heat than would be required to actually draw silver in from a rod held to the side. It also pretty much guarantees you will get an even distribution in the joint (I am assuming that you grind in a scarf joint, I don't think you can butt joint a BS blade with silver solder, but if you did, you wouldn't need much joint penetration and therefore tape would not be a big help).

Learning to silver solder is a great technique to learn, and allows one to make various tools using stuff like HSS that can be heated way up there with no loss of performance.

One normally wants an OA torch for this kind of work, because seemingly paradoxically, one wants to use the lowest heat possible, and hotter torches make that possible. But with small projects a propane torch is fine. I made this bike rack with a propane torch, before I ever got an OP torch.


Re: Re-sizing bandsaw blades

#10

Re: Yeah

Larry Clinton At Frankfort, (Central) Indiana

Every Industrial metal cutting bandsaw I have seen has a blade joining unit mounted right on the side of the saw. I have welded several. The unit has a shear, guides and clamps to hold the blade ends in position, a welding unit (push button) and an annealing operation (push button). Takes less than 5 minutes to measure, cut and splice a blade. Also as Bill said almost all woodworking sharpening service has the equipment. If you have any friend that works in a tool room of a factory, he would probably have no problem doing it for free.