Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Air Compressor Question

Posts

Air Compressor Question

#1

Air Compressor Question

Barry Irby

My Portable 6 Gallon Porter Cable Air Compressor was stolen and I replaced it with a reconditioned one. Took the "new" one out of the box and used it to nail one room of shoe molding. It may have been plugged in for an hour at the most. Set it aside in my heated storage room for a few months with the drain valve open. Went to use it today and it won't put out any air. It runs and fills the tank and cuts off, but there is no pressure in the output line. I tried turning the pressure regulator knob up and down, Had no effect.

Any suggestions? What am I missing? Is there a port of some sort between the and and pressure valve that may be clogged?

Re: Air Compressor Question

#2

Re: Air Compressor Question

Lee Schierer in McKean, PA

It sounds like the regulator is stuck. Open the regulator as far as it will go, put an air blow off in the hose and open it. and then give it a good rap. Not so hard that you would break it, but just a good jolt.

Lee

Re: Air Compressor Question

#3

Re: Air Compressor Question

Keith Newton

I hate to ask, but I think we are about the same age,,,,,,,, which means you might be missing something obvious, like,,,,,,, is the hose connected to it? ha

Re: Air Compressor Question

#4

Re: Air Compressor Question

Larry Clinton At Frankfort, (Central) Indiana

Pretty simple device, Lee is most likely correct. The only other possibility is that there is something in the tank floating around that has plugged the outlet pipe. If Lee's suggestion doesn't work the next step would be to first bleed the tank down using the drain valve - after ALL the pressure is released, remove the regulator and turn the compressor back on and see if air is exiting the pipe that previously fed the regulator. If air is escaping you have a bad regulator. If no air exits and pressure builds up you have a "plugged" pipe. Removing the pipes and inspecting / removing the obstruction(s) or replacing the regulator should not be a major problem.

Re: Air Compressor Question

#5

Re: Another possibility

Larry Clinton At Frankfort, (Central) Indiana

There is one more possibility - the snap on connector may be faulty. This might be the first thing to check. Again bleed the tank completely then remove the snap on hose connector, then turn the compressor back on to see if air exits the pipe (while turning the regulator pressure up). If it does replace the snap on connector, if it doesn't then proceed to my previous troubleshooting list.

Re: Air Compressor Question

#6

simple test

Tim Greif - West of Chicago

Pressurize the tank (or at least let it run until you think it's pressurized). Normally, the regulator and pop-off relief valve are on the same manifold. Pop the relief valve by grabbing the little ring and pull it. If air flows out of it, you have pressure at the manifold, and you have a stuck regulator as Lee said. If no air flow, you either have no pressure in the tank or the manifold is plugged. If there's no air flow and you can get air flow out of the tank drain, you have a plugged manifold.

Re: Air Compressor Question

#7

More Info and good news, I think....

Barry Irby

I called Porter Cable yesterday and they gave me the address for the local Factory Repair service. I called them and they said that if it were more than ninety days old it would cost $99 for the repairs. You can buy one of these compressors for about $169. and I am not about to pay to repair it. I am ticked that this thing crapped out after literally an hour of use, so I called Porter Cable again to register my discontent. They sent me back to Amazon to print out my receipt and said that if the unit were less than a year old they would repair it under warranty. So I did and it is less than a year. So, I am taking it in later today or tomorrow and if they will honor the warranty I will get it fixed. If not, I will try to fix it myself.

Thanks for all the suggestions. It has two pressure gauges. The one for the tank runs up normally. The hose pressure one sits at zero. I bled the tank to zero and tried it again. Nothing. It has two snap connectors for hoses. Hard to imagine both failed and the gauge reads zero. I am betting either the regulator failed or there is a blockage. The "manifold" that contains the regulator is $54. Outrageous. If I have to I will rig up a way to by-pass it install and install an after market one.

I had a spare portable unit and gave it to a friend the other day. Ain't that the way?

Re: Air Compressor Question

#8

Re: More Info and good news, I think....

Keith Newton

Barry, one last little tidbit. Some regulators have to be pushed in, or pulled out for the rotation to actuate the spring, but you probably knew that, and it should not have changed on is own since your last use.