Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

drying lumber and end checks

Posts

drying lumber and end checks

#1

drying lumber and end checks

Bill Tindall, E.Tn.

PIC 1


An approximation of a tree is a bunch of soda straws glued together by lignin. Moisture is readily transported along the length of the tree as well as radially. As a result wood dries most rapidly from its ends, much less rapidly from the flat grain face and slowest from the quarter grain. When freshly sawed lumber begins to dry the ends can dry enough faster that the ends shrink faster than the bulk of the lumber and the ends check as illustrated in the picture. This end was dried for only 2 1/2 days at moderate temperature and it shows checking already.

Studies at VA Tech have shown that end coating lumber reduces the amount to checking due to rapid end drying. However, to be effective it must be done before checks develop. Clearly in the case illustrated after 2 1/2 days end coating would have been too long to wait. That said, I have never seen lumber or logs end coated in my area, no do I do it myself except when drying exceptionally thick lumber.

PIC 2


As illustrated in the second picture, there is another type of checking that end coating will not prevent. Some logs, and especially cherry, have stress in the center of the tree. The log end will stress crack soon after the cut is made. This crack will usually be a single crack across the pith.

Re: drying lumber and end checks

#2

Re: drying lumber and end checks

Hal Taylor

Do you not get end check, or do you not worry about it?

Re: drying lumber and end checks

#3

Re: drying lumber and end checks

Yonak

Bill, does milling the boards into lumber shortly after cutting tend to mitigate checking, as well ?

Re: drying lumber and end checks

#4

not a simple question to answer

Bill Tindall, E.Tn.

Logs are traditionally cut 6" longer than nominal length, for example 12'6". When I am sawing such logs I do not end trim. After drying I see two kinds of end checks, with some lumber having no end checks. There are shallow checks that are usually numerous, extending an inch or less into the end. And there are occasional splits that may extend several inches. I have no idea what fraction of the splits would be prevented by end coating, if any. I regard the shallow checks irrelevant. In the grand scheme of converting 12' lumber to furniture I just don't get any significant waste from end checks and splits. Even a perfect 12' piece of lumber is going to suffer some waste in its length because the cuttings don't come to exactly 12'.

Commercial lumber is trimmed to about 1" over nominal length after kiln drying. This trimming typically removes the shallow checks but not the splits. Again, I suffer very little waste that results from imperfect ends.

I try to buy 12' lumber or logs. It is a compromise between easy to handle and store, and waste. Clearly end checks are more of an issue in 8" lumber than 12'.

Re: drying lumber and end checks

#5

I don't know

Bill Tindall, E.Tn.

On the commercial scale logs are not sawed soon after harvest, something in the range of weeks to a few months being a typical range.

Re: drying lumber and end checks

#6

Re: I don't know

TomD

I mill my logs within an hour or so of their being felled, there isn't any checking during that period of time. If the ends get direct sunlight, they will check immediately, but if they don't they are good to go for a while anyway. I mill the boards, and coat the ends when I get the wood home, the same day. i find latex paint is pretty good for ends. But when I can get it I prefer the clear emulsion of wax. That product is apparently made by Shell, and therefore I imagine there is an actual commercial purpose for it. Someone must be coating ends other than jut me and a few wood turners.

That secondary case is an extreme case of reaction wood. I prefer not to use that kind of stuff.


You can see the ends have just been coated, and are still drying. The wax can make quite a mess, and it isn't easy to get off stuff, which is the reason for the bag on the ground. At this point there isn't any cracking, though there is pith on that 4 inch plank, and it will always crack a little. However this piece is going to be fine even with the crack. This is either the same day, or more likely the next day. I don't normally loose the ends. The pith on the piece in the air is off center, but it isn't because it is reaction wood. Low down in the trunk, there was a lot of rot, so I trimmed it off, and just took the good bits. There is still enough for a 7 foot bench top there. It would have to have a tool tray though.

Re: drying lumber and end checks

#7

Re: drying lumber and end checks

andrew nistock

I use a product called Anchorseal which will really stop end checking due to drying. When applied immediately after felling and before milling it will, at least for me, almost stop splits in the end of the lumber. I currently have a few large red oak logs that were coated a year ago and there is just a little cracking at the ends. Wanted to mill these last year but just didn't get there. You can get the info by contacting:

U-C Coatings corp. at www.uccoatings.com or by phone at 1-888-363-2628 Give it a try.

Andy Nistock

Re: drying lumber and end checks

#8

Re: drying lumber and end checks

don stephan

Most or all the lumber from my primary mill supplier is end coated after sawing.

Re: drying lumber and end checks

#9

clarification

Bill Tindall, E.Tn.



Is the lumber end coated with something to retard drying or is it simply color coded? It is quite common for a mill to color the ends of lumber packs. This coating can serve a number of purposes- to identify the mill, species/thickness, customer, or just make it look good.

Illustrated are lumber packs color coded and not.

Re: drying lumber and end checks

#10

Re: clarification

don stephan

The coating is waxy, so I expected it was to control moisture loss through the ends.