Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

plans for an adjustable bandsaw fence

Posts

plans for an adjustable bandsaw fence

#1

plans for an adjustable bandsaw fence

gary clarke

I need plans for an adjustable bandsaw fence. I have a Delta bandsaw with adjustable fence, but it will not angle enough for the drift on my new timber wolf 1/2 in blade. I have been looking on you tube and have not found one that I think will work for me. Thanks in advance.

Re: plans for an adjustable bandsaw fence

#2

Re: plans for an adjustable bandsaw fence

Bill Howatt

Why is a new blade suffering from serious drift? Is your machine setup properly

You can make a very flexible fence with 1 board and 2 clamps.

Bill

Re: plans for an adjustable bandsaw fence

#3

Re: plans for an adjustable bandsaw fence

Terry in Edmonton

I f your blade has that much drift there is something wrong. The first thing I would do is set up the bandsaw as per this video

http://www.youtube.com/watch?v=wGbZqWac0jU

and if that doesn't work you have a bad blade. Since using this setup method I have not had any of my blades drift.

Re: plans for an adjustable bandsaw fence

#4

Re: plans for an adjustable bandsaw fence

Gary clarke

Thanks, good video

Re: plans for an adjustable bandsaw fence

#5

Re: plans for an adjustable bandsaw fence

del schisler

are you sure you have the saw set up correct ? i have the delta and my orignal fence will adjust fine . watch this video and set saw up like this and i am sure the fence will work out ok, is you gullets running in the middle of the top wheel ? that is where it should be, also the wheel's should not be co-planer like most and i belive the manul says. the link

http://www.youtube.com/watch?v=wGbZqWac0jU&list=FLYDEiGLzvqQNIl-nqvD2OOQ&feature=mh_lolz

Re: plans for an adjustable bandsaw fence

#6

Re: plans for an adjustable bandsaw fence

2b6

Authors who write books about bandsaws should see this video or see Alex's demo in person! Sure changed the way I used the bandsaw - to the better.

And another shameless plug - that little blade stabilizer Carter makes - Wow! I don't get to cut enough curves w/ it. Love it!

Re: plans for an adjustable bandsaw fence

#7

William Falberg

Re: plans for an adjustable bandsaw fence

William Falberg

Have you tried breaking the frame, rotating it to line up perpendicular with your blade, and re-welding it? Seriously: you should hold a straight-edge against the flat of the blade and see where it's pointed; if it's not in line with your fence, you have a tracking problem. If you can't get it to line up, you have a wheel- crowning problem. If your wheel's crown radius isn't equal to your wheel's radius, you have a machining problem; possibly a tire problem. When you stretch a tire over the circumference of a wheel, the rubber in the center of the tire compresses more than the outer edges and this can flatten the functional radius of the crown itself. My machinist takes this flattening into account when he machines the crowns for me and exaggerates the basic metal crown profile to allow for such stretch flattening. Test the entire length of the cutting edge's flat spots for their direction relative to the fence using the same straight edge; is the blade twisting mid-travel? That will change your degree of drift also. There's just so much to worry about. Properly crowned wheels make blade guides unnecessary.(You have to think about that for a while.) I devoted an entire chapter to wheel crowning but nobody's read it so these mysteries go on forever. Blades don't just "drift" ; they cut in the direction they're pointed.

Re: plans for an adjustable bandsaw fence

#8

Re: plans for an adjustable bandsaw fence

gary clarke

thanks to all, I watched the video and now I have the blade adjusted according to the video and every thing works like a charm. thanks again, you guys are great.