Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Half round table - a little update *PICS*

Posts

Half round table - a little update *PICS*

#1

Half round table - a little update *PICS*

Joe in a Cleveland suburb

A minor little update on my half round table...

Over the weekend I was able to spend a little time on this table and finally glued the legs on.

The joints didn't come out as tight and crisp as they should (not going to show a close-up of the joints :b ...).

I made some hide glue to use. When I applied the glue to the tenons and mortises, the glue suddenly congealed.

Not sure why. Maybe because my basement was/is so cold? Maybe because I over cooked it (the glue)?


I decided to add beading along the bottom edge of the apron.


I planed down some scrap cherry to about 3/16" and I'm using a spoke shave to round it over. I left the pieces really wide so I had surface area to put in the vise and hold it while I shape it. (My DeWalt planer sounds like it's getting ready to die. Sounds like it is really working hard. It has recently sharpened cutters too. It's close to 20 years old I guess.)


Once the bead shape is on it, I'll cut it out to proper width on the BS and apply it to the apron with a few screws.


Taking shape


I'll eventually clean it up with some sand paper.



See my ugly workbench? It's a nice workbench for the weekend handyman, but not so great for woodworking. Someday I'd like to build a proper woodworking bench.

I still have to add a back apron, then I can start on the (curly maple) top.

Thanks for looking.

P.S.

Haven't seen any updates for a while on Samantha's dresser

Re: Half round table - a little update *PICS*

#2

Ellis Walentine

Coming along, Joe

Ellis Walentine

Thanks for the update. Sounds like your glue wasn't hot enough or your shop and the wood were too cold, or maybe you weren't assembling the parts quickly enough. I guess it would make sense to do a few trial runs to get your techniques down.

Spokeshaving a bead like that is a lot of fun. After getting the profile to the rough shape, I like to back off the blade so it is barely cutting, and then refine the shape. You can get surprisingly close to a perfect profile.

I'm curious as to how you will add the rear apron at this point. Sliding dovetails?

Looking forward to further updates.

Ellis

Re: Half round table - a little update *PICS*

#3

Looking great Joe

John in NM

Aren't little tables fun?

I think Ellis is right, sounds like your glue was too cold, or the room was too cold. With small parts, you can preheat them somewhat, either with a halogen worklamp (at least until someone bans them :D ) or a space heater.

Nothing wrong with that workbench of yours, it seems to get the job done :D

I started building a new one about 10 years ago and quickly got sidetracked.... I even have the drawer guides in a box, being jealously protected from use in other projects (like kitchen and bath cabinets). I have this superstition that if I start borrowing them, I'll never finish what they were for. Kinda silly :D

Re: Half round table - a little update *PICS*

#4

Suggestion

Bill Tindall, E.Tn.

I think 3/16" may be too thick for the bead. My first guess would be 1/8" or less. The bead is going to dress up the table- an excellent addition, but a pain to execute.

You deserved what you got with the hide glue. One must never do chemistry experiments on the furniture being built- glue, finish or what ever. There is a reason nobody uses it except museum restoration staff, organ builders and those stuck in the 1700's.

I am going to make one additional controversial suggestion reinforced by a conversation I had Sat. with Robert Scaffe at a craft show. Robert apprenticed under Robert Emmett, see FWW Vol. 23. I had been wanting to meet Robert for some time and Sat. got the chance. He makes as fine a furniture as I have seen anywhere. Exceptional fit and finish and well proportioned are the pieces he designs (he also does Period reproductions).

In the course of our conversation he commented that he dislikes the modern trend of mixing wood species in the main parts of a construction, for example table legs and top. I knew I had found a kindred spirit. Your table has nice lines and ample design features. A curly maple top will muck it up. Put the curly maple top on a curly maple table.

Re: Half round table - a little update *PICS*

#5

PS- more suggestions

Bill Tindall, E.Tn.

Cockbeading is best made with a scraper after roughing out with a spoke shave or file. Use a chain saw file and file a half round into a card scraper. Polish the cutting side of the scraper.

Glue and brad the cock beading on, not screws.


drive some brads into the apron and cut them off leaving about 1/16" sticking up. Locate the bead strip and press the brads into the bead strip. Now you have both locating holes that will enable the bead strip to be removed and reinstalled for shaping, and, it can't skid when gluing.

I locate the roughed out bead strip on the indexing brads. Then I use a piece of wood the thickness of the bead height to establish the amount the bead sticks out and using this block and a pencil mark the outside radius of the bead strip. Remove from apron, band saw, shave and scrape to shape.

Re: Half round table - a little update *PICS*

#6

You may want to include this vice . . . *LINK*

Yonak

. . . on your new work bench. Clever design.

Demonstration video below.


img

work bench and vice

Re: Half round table - a little update *PICS*

#7

Jack Guzman from Maine

heat the joints

Jack Guzman from Maine

I use liquid hide glue,which has similar properties to the hand made stuff you used. When what you experienced happens to me it's usually because the wood itself is cold.Your glue was hot enough but as soon as it came in contact with the colder wood it started to congeal.Preheat your joints before glue-up. I use a small kiln,but a heat gun should do it or just put the parts in a warm place for awhile before gluing.---Jack

Re: Half round table - a little update *PICS*

#8

Re: You may want to include this vice . . .

2b6

That vice is slicker than snot on a door knob! I love it.

I've used leg vices a lot & am parcel to 'em & that one is sooo great!

Yonak did you come up w/ that?

Re: Half round table - a little update *PICS*

#9

Re: ... did you come up w/ that?

Yonak

2b, please, no. I ain't near that smart.

Re: Half round table - a little update *PICS*

#10

Tell us more....

Bill Tindall, E.Tn.

I have never seen a leg vice in any shop. Looking at the picture it is not apparent what about it is advantageous. Why do you suppose they are so uncommon? What about them is better than a Record vice which I see in most shops?

Re: Half round table - a little update *PICS*

#11

Re: Tell us more....

Yonak

That's a thought provoking question, Bill. After pondering on it for a little while, I can't really come up with anything besides hands-free tightening. ..But there's a good bit to be said for that : not only can you use both hands to position the piece while you tighten the vice, it uses bigger muscles to tighten the vice (your leg) and possibly with more force, as it's really a lever with a ratchet, if you trust the fulcrum. Not that you need more muscle to apply force but I've got a job in the shop now that requires me to tighten the vice 200 times in a day's work. At the end of the day my arm is plenty sore. It could be responsible for my tennis elbow.

Re: Half round table - a little update *PICS*

#12

Re: Tell us more....

2b6

Never Bill? May be a Yankee thing. (?)

I've worked in custom stair building & one advantage was the screw being lower down the leg. Being able to work on wider boards w/o 'em being up under your chin. I worked at one bench where the leg vises actually stuck up above the bench by about a foot er more. It was great for sawing out the horses & working down the top of the rails. Being a little elongated I appreciated not being in a half stoop trying to work. Being that the vise wasn't all that wide racking your vise wasn't that much of a problem either. HTH

Yonak where can a fella get plans to that vise. The quick in & out is sweet!

Re: Half round table - a little update *PICS*

#13

Re: Hey Bill

Larry Clinton At Frankfort, (Central) Indiana

I seldom disagree with you, but I do use hide glue on certain items. When I repair a chair, I always use hot hide glue to attach / re-attach the rungs, if the rungs have loosened, I clean them off /sand and apply hot glue and veneer to built them back up, then fit them tightly to the cleaned hole. This make a later repair much easier as ALL chairs used heavily will require this sooner or later. As far as I know Hide glue is the only glue that will adhere to itself well after an old joint has "dried / hardened". Guess it actually doesn't "cure" in the normal meaning.

I have used it on other projects like re-clamping a loose section of veneer on old furniture- works well if held at the right temperature and project is warm. You can even re-heat the glue joint and reposition if careful.

Re: Half round table - a little update *PICS*

#14

Re: plans *LINK*

Yonak

I really don't know much more about it. I did find a Sketch Up video of the plans but, after watching it, I still have as many questions as before. The video is below. I suggest doing a search for Kiefer vice for more info.


Sketch Up video