Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Brass on wood lathe

Posts

Brass on wood lathe

#1

Brass on wood lathe

Gary Smyth

I would like to remove the hex out of a standard BRASS nut and turn it into a cylinder. With a metal lathe that is no problem, but can it be done on a wood lathe, hand held, using high speed steel woodworking turning tools without damaging the tool? Minimum speed is 250 RPM. Asking first before I risk a gouge. Would it be safer to do it with a series of files?

Re: Brass on wood lathe

#2

Re: Brass on wood lathe

William Duffield

It's not an issue. It works fine. Of course the tool dulls quicker than when turning wood (except maybe that stuff Derek works with :D ). I usually use my HSS parting tool, followed by SiC sandpaper to polish the brass.

Re: Brass on wood lathe

#3

craigd

Re: Brass on wood lathe

craigd

Caveat: I've not done it, but people whose abilities I respect say is it no problem to turn brass on a wood lathe using wood turning tooling. Oh wait, I have done it, but very little: using a scraping cut, with the cutting edge centered, the tool won't catch and the results are very good (no chatter). No lubricant needed. (This was using wood turning tools and files on brass in my metal lathe).

Regular tool steel works fine, I've used old saw plate to make scrapers to turn brass into cap screws (on a metal lathe), as do files (which are hard to control). Steel wool will polish the brass wonderfully. I don't think brass is all that much harder than, say, ebony.

I don't know how you are going to hold the nut, I've chucked them on threaded rod and let the nut run up against the chuck or used washers/nuts as spacers. I imagine the "fun" part will getting the nut round.

Re: Brass on wood lathe

#4

Re: Brass on wood lathe

Dick Coers

You might get a better response on the turning message board. I've done it with a small scraper, not sure I would try a gouge. Should work though. Slow speed isn't really necessary.

Re: Brass on wood lathe

#5

Re: Brass on wood lathe

John McGaw

I've done it a few times but normally the work I'm doing is simple enough that I can simply spin the piece and attack it with files to get to the proper shape. I'm sure that turning tools can be used with caution but the result of a catch could be a lot nastier so keeping the tool rest at the right height and close to the work would be critical. I've certainly turned non-wood items on a wood lathe many times -- nuts and stone and bone and horn come to mind -- and it all comes down to appreciating the differences and choosing the correct tool and technique.

Re: Brass on wood lathe

#6

Re: Brass on wood lathe

del schisler

i didn't read any other post's yet, but i have turned alumum on my delta wood leath ,but i has some old files and ground them down to what i needed and it worked out fine, i don't belive i would use any wood turning tool's , mine are richard sorby and cost some dollars files were free my 2 cent

Re: Brass on wood lathe

#7

Re: Brass on wood lathe

Bill Tindall, E.Tn.

controlling the depth of cut on the points is the difficult part. I would suggest rounding the corners of the nut with a file first.

Lathe tools are typically made from M2, the same tool steel used for metal lathe bits. Hardly an issue for turning brass so long as you don't catch the tool on a hex point.

Re: Brass on wood lathe

#8

Re: Brass on wood lathe

Gary Smyth

Sorby are mine too, but I have a few "flea market" tools that I can experiment with if filing fails.

Re: Brass on wood lathe

#9

Re: Brass on wood lathe

TomB

I have done some shaping of brass pipe fixtures (for urn threads) and it can be done on the lathe no problem. The best tool for me was a scraper, not a gouge.

Re: Brass on wood lathe

#10

Re: Brass on wood lathe

TomD

I used to do this on my lathe before I bought all the metal lathes. Metal lathes hold everything solid, and may run at low speeds, but since one is not able to lock out the tool on the wood rests, I would take the speed up enough so that the tool can't follow the surface of the object being turned. I don't know if you can cut with a gouge, but rubbing a bevel would not help much when starting out with a hex.

You can actually make a simple metal turning lathe, by mounting one of those x-y tables that are sold for drill presses, to your ways, and mounting a tool to it. This will allow you to do a lot of the stuff a metal lathe does. There is even a simple CNC thing that works out threading.

Re: Brass on wood lathe

#11

Re: Brass on wood lathe

John Lucas

I haven't read all the answers above but it's very easy using HSS turning tools. I know a lot of people recommend using a scraper but I just use a spindle gouge. Use a fairly high speed and don't force the cut. You will get nice curly shavings and clean cut if you have right speed and proper bevel rubbing cut with the spindle gouge.

I use them for Ferrule's on my turning tool handles.