Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Morse Taper Problems

Posts

Morse Taper Problems

#1

Morse Taper Problems

don stephan

My PM hollow chisel mortiser has a "female" chuck that slips onto a morse taper at the end of the motor shaft. Yesterday trying to make 1" mortises in poplar the chuck lost its grip with the motor shaft and spun for a few seconds until I backed off the mortiser.

I am ordering Tapermate cleaners for #1 and #2 morse tapers, and will use on the inside of the chuck. The bottom 3/8" of the motor shaft taper has slight parallel grooves around it from the spinning chuck. How should I try to address these slight grooves?

Re: Morse Taper Problems

#2

Re: Morse Taper Problems

Barry Irby

I would try using a fine diamond hone on it, if you have one. One of those diamond plates with the diamonds on it.

Or you could put some 400 or 600 or higher grit sand paper one a small stick and use that. I would press either of them gently on the shaft with it running and only dress away the bumps. Do no reduce the shaft diameter.

I have also used similar sandpaper on a dowel to clean the inside of Morse tapers.

Re: Morse Taper Problems

#3

Re: Morse Taper Problems

Dick Coers

Are you certain it's a morse taper? Could just as easily be a Jacobs taper or Brown and Sharpe taper. Find out what taper it is, then buy a reamer to clean up the socket.

Re: Morse Taper Problems

#4

Re: Morse Taper Problems

William Duffield

Dick is right. The taper that fits in the drill chuck is much more likely to be a Jacob's taper. But which one depends on the size of the chuck, and that could depend on which PM mortiser you have.

Here is a table of dimensions: http://www.victornet.com/reference/Morse_Jacobs.html

Re: Morse Taper Problems

#5

Re: Morse Taper Problems

don stephan

that is a real eye opener - I don't recall ever hearing about the other tapers. The chart will probably enable me to easily identify the taper, although I will also call Powermatic support for confirmation.

Think I'll still order the TaperMate cleaning tools for Morse tapers #1 and 2 to have on hand. By chance, would you know if there are cleaning tools for the Jacobs tapers.

The mix of contributors and knowledge on this forum is invaluable.

Re: Morse Taper Problems

#6

Re: Morse Taper Problems

William Duffield

I suspect there must be, but I've never run into one, because I haven't looked. For applications expected to be used by woodworkers, a Jacob's taper is not likely to be removed from the chuck, so cleaning out of crud is not nearly as likely to be needed as with a Morse taper, which is used to hold lots of interchangeable chucks in both lathe headstocks and tailstocks and in drill presses. Typical scenario: You buy a Jacob's chuck, and at the same time you buy a taper adaptor with a Jacob's taper on one end and a Morse taper on the other to fit your machine. You then install the taper adaptor in the chuck, and it stays there until you croak.

Re: Morse Taper Problems

#7

craigd

So true ...

craigd

When I buy chucks, they are without arbors, so you also buy a (or 2) arbors with the tapers needed (in my case, Morse #? on the tail stock end and Jabobs J? on the chuck side). And leave them there until they die. Or move them to another machine, which I have done couple of times.

Re: Morse Taper Problems

#8

Re: Morse Taper Problems

BrianMonumentCO

This link has a list of different tapers and dimensions for them.

It might not hurt to compare what you have with it prior to ordering.

http://littlemachineshop.com/Reference/Tapers.php

Re: Morse Taper Problems

#9

Another taper reference

BrianMonumentCO

http://www.victornet.com/reference/Morse_Jacobs.html

Re: Morse Taper Problems

#10

Re: Morse Taper Problems

don stephan

Measured the small end with dial indicator and didn't match up with anything in the table. A friend looked at the chuck in a raking light and was able to make out "33 taper" suggesting a Jacobs 33. The manufacturer's tech support didn't have any idea of the taper, so I simply ordered a new chuck. The inside was scratched up some so seemed wiser to replace than risk further damage to the motor shaft end.

Re: Morse Taper Problems

#11

Re: Morse Taper Problems

Dick Coers

As mentioned, you'll probably have to lightly work that shaft a little. Any time I've seen grooves cut, there is also some metal on the high side. Remove as little as possible, but the new chuck won't grab if there are high rings on the shaft.

Re: Morse Taper Problems

#12

Re: Morse Taper Problems

William Duffield

A #33 Jacob's taper is what one typically finds in a three jaw Jacob's chuck with a maximum capacity of 1/2". A 5/8" Jacob's chuck typically has a #3 Jacob's taper. I don't know which size taper is used on the very small chucks that are used in bench top hollow chisel mortisers.