Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Anything wrong with modding a Biesemeyer this way?

Posts

Anything wrong with modding a Biesemeyer this way?

#1

Anything wrong with modding a Biesemeyer this way?

Henry Higginbotham

For years, I used an Incra TS fence system on my Unisaw. The fence itself is an aluminum extrusion to which you can mount just about any sort of accessory. Feather boards, fence stabilizers, height extensions, etc. I kind of came to take this for granted.

I recently changed over to a Biesemeyer commercial fence which has no such mounting provisions. I'm thinking of adding three or four 1/4-20 rivet nuts along the top of the tube. When nothing is attached via the rivet nuts, they would be comfortably below the height of the sides of the fence. But when needed, all sorts of shop-made gizmos might be attached.

I don't readily see any reason not to do this, but then I know that I usually find out why I shouldn't do something after it's too late. But I'd bet several of you have done the same thing, so what worked or didn't work?

Re: Anything wrong with modding a Biesemeyer this way?

#2

Re: Anything wrong with modding a Biesemeyer this

William Duffield, on the Cohansey

I can't help you with drilling holes in a Beisemeyer fence, because I never felt the need for it. I use a different strategy when I want to secure something to the fence. I use a couple of these:

http://festoolownersgroup.com/festool-tool-reviews/review-of-festool-quick-clamp-(491594-eu)/msg103148/#msg103148

Whatever appliance I want to attach, I drill a couple of 1/2" ø holes in the top, drop the clamps over the top of the fence and into the holes and clamp the appliance to the side of the fence. These quick clamps have an advantage or two over typical F-clamps, in that they have narrower heads that drop into smaller diameter holes and also slide into Incra t-track if you want to use them with other fences for drill press, router table, etc. I also use them to hold flip stops to extended miter fences.

Re: Anything wrong with modding a Biesemeyer this way?

#3

Rick L

Re: Consider T-track...

Rick L

You can do whatever you want. You might consider putting some strips of T-track instead. More flexible option in my experience.

Re: Anything wrong with modding a Biesemeyer this way?

#4

Re: Anything wrong with modding a Biesemeyer this

Jesse Cloud

The fence is basically just a long square steel tube with a piece of particle board screwed (and countersunk) onto the two vertical sides and covered with formica.

Other than appearance, I don't see any problems as long as you make your holes sorta in the middle. I guess also be sure that anything protruding over the business side of the fence can be easily moved to allow for tall pieces.

While you are at it, check to see if your fence is square to the table vertically. Besse/Delta shims the particle board to try to make it so, but I have seen several that are off plumb.

Please post a pic of how it winds up!

Re: Anything wrong with modding a Biesemeyer this way?

#5

Re: Anything wrong with modding a Biesemeyer this

Robby Wright - San Marcos, CA

Henry - You can do what you are thinking about. I use the Rockler Universal Fence Clamps to clamp sacrificial faces and such to my Biesemeyer - they work fairly well. Here is the link:

http://www.rockler.com/universal-fence-clamps

One thing to watch for: The rear end of the fence isn't fastened down, so you have to clamp the rear of the fence if you want to use something that presses downward. I have seen many ideas for little hooks that engage the back rail, and others that have used a clamp when necessary. The T-rail idea is a good one too.

Good luck with yours!

Robby Wright

Re: Anything wrong with modding a Biesemeyer this way?

#6

Re: Anything wrong with modding a Biesemeyer this

J. Waters

I have clamped the back of my Bies down before, but it's been rare. Been real happy with mine, but yes it's different than a Unifence (or smaller brother, Precision saw guide which I had before the Bies) and I had to change or modify my jigs.

I still like my Bies better than a Unifence. Of course, I used enough Jet Lock fences of old to hate those......

Though my Bies is a Mesa, AZ made one, and it was great out of the box. Of course I aligned it 13 years ago and it's never needed adjustment (really!)