Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Is it possible to bend an aluminum casting?

Posts

Is it possible to bend an aluminum casting?

#1

Is it possible to bend an aluminum casting?

Tim Greif - West of Chicago

I have a Makita 12" CMS (LS-1220) that has developed a slight warp in the fence. I have no idea how, but it is now slightly concave by about 1/2-1 degree. If you lay a straight board on the bed, there's a slight gap in the middle at the blade slot. When doing miters, I can compensate, but I would prefer to have it corrected. A new fence is $54 so would rather try to bend it back. The worst I can do is have to replace it anyway. Anybody ever done something like this. I do not have a press or I'd try it myself.

The fence is shown below.


Re: Is it possible to bend an aluminum casting?

#2

Re: Is it possible to bend an aluminum casting?

Tim Caley

Can you flatten the back on a piece of sandpaper and the surface of your tablesaw like is done for the bottom of a handplane?

Re: Is it possible to bend an aluminum casting?

#3

Re: Is it possible to bend an aluminum casting?

del schisler

i have the same saw, what i have done is use a nice piece of maple a little taller than the fence and bolt it across the complete fence, now i do mostley 45 degrees so all i did was cut a slot when i made a cut, the oping is real big and i was cutting a cut and a piece of the cut off went in and jamed and bent some item's , it has been a long time ago and that is when i needed a smaller opining i belive the piece will just break before you can bend it , also i belive it will just spring back , if you know some one in a auto repair that planes heads and have them sand it down flush that would be the best and than polish it or the plane down job may be smooth enough good luck

Re: Is it possible to bend an aluminum casting?

#4

+1 on sanding it flat. 80 grit on a flat surface

Dick Coers

On the other hand, did you measure the bend while it was bolted on the saw or unrestrained? The torque of the bolts may put some bend into it.

Re: Is it possible to bend an aluminum casting?

#5

Both

Tim Greif - West of Chicago

It's cupped in both the bolted and unrestrained state. I suppose tightening the fence bolts long ago is what could have distorted it, but I only noticed this about a year ago and I've had the saw for a number of years. I don't ever recall moving the fence once it was initially set up. I can bolt down one end of the fence and force the other end to darn-near flat, but not quite.

To me, it seems like it would take a lot of material removal sanding on a flat surface to get it right. Gotta think about this one.

Re: Is it possible to bend an aluminum casting?

#6

Re: Is it possible to bend an aluminum casting?

Bruce, a MN Galoot

Find a good machine shop and have them surface grind it. Machinists can do amazing things. I wouldn't try to bend it, especially a casting.

Re: Is it possible to bend an aluminum casting?

#7

Not likely

Mark Mandell - Gone Round In New Jersey

Castings form a crystalline structure in the metal that will resist being bent and will be more likely to break. What you describe appears to be heat-induced warp in the casting. Remedy is to machine the surface flat. If that process will take too much metal, you may then have to reface the fence surface with two pieces of alu plate either bolted or welded to the casting.

Re: Is it possible to bend an aluminum casting?

#8

Sometimes, yes; gentle is the word

Bill Houghton, Sebastopol, CA

I've straightened some aluminum stuff with very gentle pressure applied for a while, like a week or so. Prop up the ends and apply weight in the middle. Weightlifting weights, bags of flour, that kind of thing, applied in a way that forces it in the direction you want, but only that direction.

Again, gentle is the key. One of the problems with aluminum house wiring when it first came out is that aluminum will "creep," and the connections were getting loose. You want to take advantage of that "creep."

Re: Is it possible to bend an aluminum casting?

#9

Re: Is it possible to bend an aluminum casting?

BrianMonumentCO

Depending upon how old the saw is you might be able to talk the vendor into replacing the fence.

Calling the customer service line might lead you to a solution including a replacement.

Re: Is it possible to bend an aluminum casting?

#10

Re: Is it possible to bend an aluminum casting?

Chuck in Mtl.

What if you bolt one end down and then try to bolt the other to make it straight and then use a propane torch to make it permanently straight? I have heard of this being done to aluminum heads...using heat to bend it straight.

Re: Is it possible to bend an aluminum casting?

#11

Lap it

Grant in Iowa

Tim,

Suggest you apply some auto body wet/ dry abrasive sheet such as 320 or 400 grit paper to the surface of your table saw or other flat surface using spray adhesive such that the abrasive area is large enough to place the offending part of the saw on and lap it. Your part might take 2 sheets placed next to each other for a large enough area.

Remove the saw fence and lap it by hand on the surface until it is flat. Not sure if my grit suggestions are correct for the amount of material that must be removed, but you will eventually get it flat in that way. When done the paper can be removed with a scraper and the table cleaned with solvent.

I have lapped many items in that way including automotive parts like water pumps, thermostat necks, etc. with great success. Hand planes and the like can also be done in this way.

FWIW,

Grant in Iowa

Re: Is it possible to bend an aluminum casting?

#12

Re: Is it possible to bend an aluminum casting?

Robin Corell in Atascadero,CA

Lord of miss information in this thread. the vast majority of aluminum castings are 356 which can be easily bent. In fact when I worked at an aluminum foundry we had a guy whose job was to straighten all the castings. He made jigs for each job and then used rawhide hammers and a surface plate to get things back within tolerance. The key to straightening an aluminum casting is to use a rawhide hammer or a dead blow hammer. It doesn't take a lot of force so sneak up on what you want rather than trying to get it in one whack. I had to do the exact same thing to my Makita.

Cast iron on the other hand can not be bent.

Re: Is it possible to bend an aluminum casting?

#13

Rick L

Re: Cast iron can be bent...

Rick L

40 years ago when I bought my second jointer (powermatic 6") there was a slight bow in the fence and the regional salesman mentioned being able to slowly coax by slightly overbending. I've done this many times over the years.

Re: Is it possible to bend an aluminum casting?

#14

I agree with Robin

Sophie Gold Beach OR

Most castings like wheels, alternator housings, brake calipers, air cooled motors and such are made with foundry metal like 356.2. The problem with the 356 series is that it is about 7 percent silicon which makes it very strong, brittle, and has great abrasion resistance. It can be bent but only very little before it will break. Tim with that said from what you are asking to do, yes it shouldn’t be a problem to ‘coax’ your fence into alignment. The question I have is can you do it and still keep the fence at a 90 degree angle to your table? If it was just a flat piece of metal it would be no problem but your fence is actually two fences connected together on the ends of a horseshoe. When you bend the fences flat that horseshoe will more than likely bend up toward you a little making your fence no longer at a right angle to your table. Bottom line is that if it were me I’d take it to a machine shop and have it ground flat and true or order a new fence whichever is cheaper.

Sophie, who helped make 1.8 million lbs. per day of aluminum from raw ore for 36 years.

Re: Is it possible to bend an aluminum casting?

#15

Sure can!

Tony - Memphis

I used tio be in the high performance valvetrain biz. Every cast iron camshaft we made was bent during grinding. We had a straightening station at the end of the line to straighten them. It was really crude, but it worked. They used an air powered chisel. We had an arm with several dial indicators that could be located on the journals. It took some finesse. I could get one straight but never mastered it. Crankshafts can bend too!

Tony

Re: Is it possible to bend an aluminum casting?

#16

Re: Is it possible to bend an aluminum casting?

Pat Riley

I had the same problem.

Fixed it a different way that only took about an hour.

Glue (I used epoxy) a 1/4-3/8" thick piece of scrap (I used hard maple) to each side of the fence.

When it is dry, send it across the jointer a couple times until all face is flat and true to the base.

It is a lot easier than trying to bend it, and it can be run back through the jointer whenever you think things are out of true.