Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

O.T. Faucet Removal

Posts

O.T. Faucet Removal

#1

O.T. Faucet Removal

Stuart Johnson

I need to remove an outside faucet and am concerned about messing up the pipe. It's a 25 year old copper pipe with a normal brass type faucet that screws on. I doubt if it has ever been removed. What would be the best way to break the seal so it will unscrew? Will regular penetrating oil work or does copper/brass need something different?

If I screw it up I'll need to open the bedroom wall to replace the pipe and that leads to all sort of other issues.

Re: O.T. Faucet Removal

#2

Jack Guzman from Maine

Re: O.T. Faucet Removal

Jack Guzman from Maine

Steel rusts and joints tend to fuse together but brass shouldn't do that. Penetrating oil should do the trick. If it doesn't why not just cut the copper pipe and put a cap on it? If it isn't possible to sweat it on ,use a sharkbite cap.---Jack

Re: O.T. Faucet Removal

#3

Re: O.T. Faucet Removal

Dick Coers

Personally, I wouldn't care to have penetrating oil get into my drinking water. Just me. Big with some teflon tape or pipe dope on the threads, I really doubt if penetrating oil is going to get in to help or get to the water. I guess you can't grab the pipe with anything to resist the torque? Sounds like a crap shoot to me. Have the wife my the main shutoff!

Re: O.T. Faucet Removal

#4

Been There - Done That

Marvin Horn

Wish I had the answer, I had knock a hole in the bedroom sheetrock to make repairs.

If there's not enough "spring" in the copper pipe to allow getting a wrench on the threaded adapter from outside the wall , it's just a crap shoot. I doubt if penetrating oil would get through the thread compound or teflon tape. Heat on the faucet might do the trick.

Re: O.T. Faucet Removal

#5

Re: O.T. Faucet Removal ++ Shark Bite

Bob Entwisle in NJ

Pick up a shark bite cap... just in case. Sharkbite fittings are the greatest thing since sliced bread, IMHO.

But a little heat, or a good penetrating oil, Kroil or the like should get the job done.

Bob in NJ

Re: O.T. Faucet Removal

#6

Re: Been There - Done That

Mark Mandell - Gone Round In New Jersey

1 cut off the water.

2 open the valve and drain the line

3 remove the valve stem

4 apply heat to the valve away from the wall

5 gently turn off the valve body that will have slightly expanded from the heat making the threads easier to move

ps heat = warm not "sweat hot"

Re: O.T. Faucet Removal

#7

Shark Bite

Mark Mandell - Gone Round In New Jersey

May leak when applied to threaded pipe end.

Re: O.T. Faucet Removal

#8

Been there, done that . . .

steve mackay

From the age you mention, please, PLEASE make SURE it is indeed threaded on ! This house is about the same age. Same set up (copper pipe/brass fitting). The spigot APPEARED to be threaded on. I cranked on it and it WAS NOT ! Cracked the pipe. Youu can try oil (I would) BUT if it still doesn't turn with light preasure, STOP ! Go ahead and open a small (controllable) hole in the bedroom to get ahold of the pipe. This way, the "water emergency" is on YOUR terms. I would have bet my retirement check that sucker was threaded on. It had the "nut" shape to fit a wrench on it. Why, I do not know. But, Brother, it was NOT threaded !

Re: O.T. Faucet Removal

#9

Let us know...

Tony - Memphis

I have similar issues. Mine leak a little now and then, but I'm scared to try and remove/replace them. Pretty sure mine are threaded, but after readign below...who knows! Mine are even covered with mortar. I looked for repalcement seals (packing nut seal?). but I couldn't find such a thing. Next thought was to just buy a replacement and steal the guts? Fortunately, not an issue...at present. One of mine was leaking during the really cold weather here. I was afraid the wet parts would freeze and break bricks/mortar, but it didn't and I was able to stop the leak. Good luck! Be careful!

Tony

Re: O.T. Faucet Removal

#10

Jack Guzman from Maine

Re: Shark Bite

Jack Guzman from Maine

If he can get the fitting off to expose the thread he doesn't need a sharkbite fitting.A threaded cap will do just fine.The sharkbite is needed only if he has to cut the pipe.---Jack

Re: O.T. Faucet Removal

#11

If

Mark Mandell - Gone Round In New Jersey

it's actually a threaded rather than sweated pipe/fitting ;)

OTH, if it's an outside "frost-free" valve, he'll be opening the inside wall no matter what.

Re: O.T. Faucet Removal

#12

Re: O.T. Faucet Removal

Barry Irby

Wouldn't it be easier to rebuild the faucet? Why is it leaking. Is the Seat/Washer? Should be easy and cheap to polish the seat and replace the washer. If the stem is leaking you can replace the packing. And the stem should only leak if the faucet is "ON". I have not looked, but You Tube must have a tutorial.

Re: O.T. Faucet Removal

#13

Re: O.T. Faucet Removal

Stuart Johnson

Mark might have hit on the problem with the frost free faucet. I don't know if it is or not and hadn't thought about that possibility. It is definitely threaded but the stem is so long I can't get in far enough to polish the seat. There are two of them, one behind the bedroom wall and one in the utility room. I can't get to it until late next week at the earliest but I'll tackle the utility room one first. If I have to go through the drywall in there it won't be an issue. I have tried large patches in the past and they look like large patches so a nice bead panel might be the solution in there.

Re: O.T. Faucet Removal

#14

Re: O.T. Faucet Removal

Barry Irby

Locally, faucets are generally installed through the foundation wall and not in the wall of the house. Unless the house is on a slab.

You did not describe the wall. Unless you have a brick veneer house an ordinary stud wall would be pretty thin for a frost free faucet. Again, locally they are usually 6 to 12" long. The ones I am visualizing are designed with the handle on the front and a straight tube back. Seems like it would be possible to extend the little rotary file with a rod and polish the seat. Have not done won in years.

Re: O.T. Faucet Removal

#15

Re: O.T. Faucet Removal

Tony - Memphis

Interesting how different these things can be based on region. Here, the faucets are through the brick veneer wall and often not fastened to the wall. Mine are free to wiggle. Some are held in place by mortar. I looked for something like a rebuild kit, but I couldn't find anything. That's when i thought about buying a replacement faucet just for parts. Oh, these are just plain old faucets in our area, nothing frost free or such.

Tony

Re: O.T. Faucet Removal

#16

I had the same Problem....

Barry Irby

on the last house I flipped. Needed to replace the handle on the outside faucet. Snowballed from there. Could not find a replacement handle or Identical faucet. I knew the main water shut off valve under the house did not work well and that the handle from it would work on the outside faucet. So, to be a nice guy I decided to replace the main valve and then swipe the handle off it to put on the outside faucet. Needed to turn the water off at the street. Found the valve in that was cranked over int a very odd position and could not get any sort of wrench on it to turn it off. Reported it tot he county and they changed it out. Then replaced the main valve and put the handle on the outside faucet, only to discover that the reason the previous owner had removed the faucet handle was apparently because the piping to the faucet had frozen. Then discovered the interior shutoff valve to that had basically disintegrated. So I replaced the interior shut off, the piping and the whole exterior faucet. Sheesh!

Re: O.T. Faucet Removal

#17

Re: I had the same Problem....

Stuart Johnson

One thing leads to another. My wife told me some paint was flaking in the bathroom. By the time I was finished with that little bit of flaked paint I had:

1. Ripped out all drywall around the shower.

2. Taken out the actual shower because of a broken pan.

3. Re-framed for new shower after removing termite eaten studs.

4. Had whole house treated.

5. Re-built shower pan.

6. Re-built and tiled shower.

Lessons leaned.

1. New fixtures in the shower means new fixtures for the entire bath.

2. If a can of paint is opened in one room the entire house interior has to be painted.

3. Never, ever pick at loose flaking paint. Instead sell the house and move out of state.

Re: O.T. Faucet Removal

#18

Holy cow!

Tony - Memphis

I've been tempted to buy a condo after all the home stuff we've encountered recently. We were spoiled moving into this house when it was new...it ain't new anymore!

Tony