Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Metal Bracket for Tripod Pedestal Table

Posts

Metal Bracket for Tripod Pedestal Table

#1

Metal Bracket for Tripod Pedestal Table

Joe Burke

I can only take a stab at describing this, so here goes.

I've repaired a pedestal table. Three legs in,what I believe is, typical Duncan Phyfe, splayed leg, style. The legs did exactly what you'd expect them to do when years of downward pressure had been applied. They broke loose from the pedestal. They'd been doweled to the pedestal so I cleaned them up, enlarged the dowel holes and put them back. It was way more complicated than that, but let's keep it simple.

I've seen metal brackets in the past designed to prevent the very thing that happened to this table. The bracket would be round ... smaller than the dia. of the pedestal base ... and have 3 wings, if you will, at 120 degrees around the perimeter that would line up with the legs and actually lap over the legs. The wings would be screwed to the legs and the center of the bracket would be screwed to the center of the pedestal. This would, in effect tie all the legs together and resist the down force that pulls the legs from the pedestal.

If no one gets this I could draw a picture, but I'm hoping someone will know what I'm talking about.

What would this be called? I thought it was called a spider? I know doggone well I've seen them in catalogs before, but I can't find anything anywhere about one of these things. I've Google searched everything I can think of using all the verbage I can muster. So far nothing. What is this thing?

I already know I'll have to make what I want and that's not a problem. I'm just frustrated at my inability to find this wretched thing!

Somebody help ... just a little.

Re: Metal Bracket for Tripod Pedestal Table

#2

Re: Metal Bracket for Tripod Pedestal Table

Barry Irby

The current (April) issue of FWW Has and Article , "Build a Classic Shaker Table" and it uses one. They call it a spider and note that you can get one form hortonbrasses.com. Good luck

Re: Metal Bracket for Tripod Pedestal Table

#3

Funny ... and a little sad

Joe Burke

That issue was laying on the floor in the office, directly behind me, not 3' away. I'd swear, too, that I'd looked at Horton Brass catalog.

Thanks though.

Re: Metal Bracket for Tripod Pedestal Table

#5

Re: Metal Bracket for Tripod Pedestal Table

William Duffield, on the Cohansey

If i am not mistaken, Londonderry and Ball & Ball should also carry spiders, but I'm having a bit of troubhe searching their catalogs to confirm that.

http://www.ballandball-us.com/

http://www.londonderry-brasses.com/

IMHO, any tripod pedestal table joined with dowels instead of sliding dovetails is a cheap immitation, even perhaps bordering on a forgery. Anyone who has repaired any of these should realize that if they were to build a reproduction from scratch that they should immediately install a spider, and not wait until the table is broken to repair it with one. Of course, there have always been those who have called themselves craftsmen, but were more interested in the fast buck than building something of quality and durability.

Re: Metal Bracket for Tripod Pedestal Table

#6

Re: Metal Bracket for Tripod Pedestal Table

Joe Burke

Again ... Funny

I bet I searched for "spider for pedestal table" ... "metal bracket for broken pedestal table" ... it goes on and on.

Re: Metal Bracket for Tripod Pedestal Table

#7

Re: Metal Bracket for Tripod Pedestal Table

John McGaw

I've only needed one but I made that in-shop from a piece of heavy(ish) brass sheet from the hobby shop. It was easy to lay out and cut the shape using hand tools.

Re: Metal Bracket for Tripod Pedestal Table

#8

Re: Metal Bracket for Tripod Pedestal Table

William Duffield, on the Cohansey

As it has been ever since this furniture form was invented. And if you didn't have a brass plate, maybe because you were living on the edge of the frontier, surely there was a blacksmith in town, down the road under the spreading chestnut tree, who could easily forge one for you from iron. No need to weld it, or harden it, or anything special, just cut it to size and bore four holes in it for screws.

Re: Metal Bracket for Tripod Pedestal Table

#9

Another thought....

Barry Irby

If this is a three legged table you could drill through the post form the opposite side and install a lag bolt or two and ten plug the holes with matching wood or put the covers on used for bed bolts.

Re: Metal Bracket for Tripod Pedestal Table

#10

Re:  Another thought....

Joe Burke

I did consider that, but as a last resort. I managed to jig up and pull the legs into place quite well. A spider should do the trick.

The table's history actually dictated what I would and wouldn't do to repair it. The table was made by the man that was the head of the department for my major in college. I knew him and took classes under him for 4 years. He helped get me my first job, and I wound up teaching with his daughter. He's been gone a while now, but his daughter has all the furniture he made. So, when the table needed repair I got to be involved.

It's been a treat really. I spent a lot more time reflecting on Dr. Young and our time together than I ever thought I would while working on the table. I'd bet it was made in the 60's or 70's for his wife and family. I suspect it's made of sweet gum, but I don't know for sure. It's not a premier cabinet wood at all. However, the finish makes it look like it could be. It was a functional piece built on a budget I'd say. Well made in spite of certain compromises that might have been made. No dovetails. How dare he ... the fraud.

Sorry to ramble.