Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Old piano finishes

Posts

Old piano finishes

#1

Old piano finishes

Joel Weber

Hello,

I work with pianos (tuning, rebuilding etc...) but note there are few good refinishers available, and

these are quite pricey.

I know very little about finishes, but would like to find a fairly simple method of adding luster and

shine back into old piano finishes (without stripping or spray guns).

I tried some Polyshades but it flashed quickly and got gummy almost immediately.

I've used Watco (Danish wood oil) and it looks nice but always feels oily...

I've heard of using Old English (scratch remover) but have not tried it.

** Can I use an oil (like those just listed) and then add a coat of Sparurethane, or lacquer to add

some shine and create a harder topcoat?

Re: Old piano finishes

#2

Re: Old piano finishes

Keith Newton

Have you tried any of the auto finishing supply products. i have used some glazes with a wool bonnet on a slow speed right angle grinder/polisher. it can bring it up to an amazingly high level, if there is enough finish on it to start with.

You have to be careful around the edges, or sharp corners, and make sure that the tilt of the pressure is off the top, out and away, or it will remove the finish down to bare wood on the corners. And the whole room needs drop cloths. This will sling a spray or splatter 360º. I think I may have gotten a polishing head with my last random orbit sander, which would make a much less aggressive tool, but I have not tried it.

Re: Old piano finishes

#3

Re: Old piano finishes

Barry Irby

Almost sure the finish is lacquer. You can test that with a little lacquer thinner. Put some on a paper towel or cloth and wipe it on an inconspicuous spot and see if it softens the finish. Then you can go from there. Clean thoroughly and add more lacquer. If the finish is sound you may be able to buff it either by hand or power buff as mentioned above.

Re: Old piano finishes

#4

Re: Old piano finishes

john Veerkamp

50+ years ago I worked for a shop re-finishing pianos. We always used lacquer. I'd bet that is what yours is.

Old English scratch cover is basically a non-drying oil with some dye in it. There are two flavors, one for dark and one for light wood.

If the scratches are small try matching with markers. Other wise get a dye stain and wipe into the damaged areas. It will wipe off the good finish with no problems.

Re: Old piano finishes

#5

Re: Old piano finishes *LINK*

Dick Coers

Ditch the big box store stuff, and get some training and products from Mohawk. They have 2 day classes all over the United States. Their products are made for touch up and refinishing. High quality stuff!


Mohawk training schedule

Re: Old piano finishes

#6

Re: Old piano finishes

DLCinSTL

Your description of wanting to add "luster and shine" suggests that, generally the piano finishes aren't deeply scratched, but simply somewhat dull in appearance from very fine scratches. For lacquer, there is an array of automotive refinishing products available from companies such as 3M or Meguiar's that are for the specific purpose of restoring, i.e., polishing, painted finishes.

Depending on the degree of "dullness", one can begin with a course product, then work in steps to the very finest product. You may have to do some shopping to find an automotive store or auto-body supply store that carries a product for hand application, as these type products are generally used with buffers in a shop environment.

These products range from: rubbing compounds, generally for newly sprayed or very dull surfaces; polishing compounds, which are to be used after the rubbing compound is used or for lightly dulled surfaces; or swirl removers, which are used to polish out the last of the marks left by the polishing compounds.

For hand use they are all used similarly. Using a slightly damp, folded cotton cloth, apply the product sparingly to a small are, rubbing in circles. As the product begins to dry, apply lighter pressure, then buff clean with a soft cloth and move on. Don't expect to not see some dullness until you finish with the swirl remover, as all the previous compounds will leave some dullness. And don't let the cloth get too dirty or built-up with compound.

I would think that for what what you want to do, you can start with one of the finest polishing compounds and quickly move to the swirl remover.

And don't go overboard and rub through the finish, especially on the edges. Regretfully, it's like so many other things in life, it takes practice. But here is the good part. You can find yourself an older car with a worn finish and practice on it. That way, you can get a feel for how the different compounds work in relationship to each other. And the darker the finish the better. That's where a dull finish shows up the most.

Re: Old piano finishes

#7

Your best bet.

Bill Tindall, E.Tn.

If you are unwilling to learn to finish a piano as it was done originally(not a simple task) your best bet is to hire someone to do your finishing. The original finish would be lacquer, sprayed, followed by rubbing out. There is no quick and easy way to replicate this deep lusterous finish or shortcut to learning how. I would not be surprised to find that one of the highest paid employees in the Steinway factory is the person doing the finishing.

Re: Old piano finishes

#8

Re: Old piano finishes

del schisler

go here and read https://www.google.com/#q=piano+lack+finish

also here https://www.google.com/#q=piano+lack+finish+in+a+rubbing+finish

Re: Old piano finishes

#9

Teri Masaschi

Howard in Toronto

She specializes in restoration.

She does the finishing for other woodworkers. And she consults too.

Super skilled plus a great communicator.

Howard

Re: Old piano finishes

#10

Re: Old piano finishes

Joel Weber

Thank you all for taking the time to offer some suggestions.

I appreciate your insights, and can concur that in the world of stellar finishes, pianos seem

to set the standard - making it an incredible challenge to maintain or partially rejuvenate.

Just so you all know, a high-end complete 6' piano refinishing (not high gloss polyester) will

run $6500 - $9000.