Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Pedestal Technique Take 2

Posts

Pedestal Technique Take 2

#1

Alan Young

Pedestal Technique Take 2

Alan Young

I am planning out work for a pedestal Table:

Here are the profile requirements:


Will this lamination scheme work? The outer circle on top is the final outside diameter, the middle circle is the cut-in, and the furthest inward circle is the approximate diameter of the open space from the laminations-This yields a 3/8 inch thick wall at the cut section.I'd like to avoid using solid lumber all the way through if possible. After gluing these boards up I would cap each end with a plywood plate and center the piece in the lathe for turning...Any pitfalls to this plan? Thanks, Alan


Re: Pedestal Technique Take 2

#2

Engineering

Mark Mandell - Gone Round In New Jersey

Lamination will work for the turning but you may want more meet on the narrow axis for your fixing hardware at top and base

Re: Pedestal Technique Take 2

#3

Re: Pedestal Technique Take 2

Bob Lang

I would leave more meat, at least 3/4" at the thinnest point. I would also consider making a coopered octagon (not as hard as it sounds). I foresee issues with keeping all those stacks from sliding around as you assemble, and the sides that show all the edges won't look so good compared to the sides that show mostly face grain.

Bob Lang

Re: Pedestal Technique Take 2

#4

Re: Pedestal Technique Take 2

Barry Irby

If you have the stock, I would make it out of something like 2 x 3" and use staved or coopered construction. I have made several that way and they worked out well. I am sure it will make a much better looking turning. (That's my opinion and I am sticking to it.) It was fairly easy. Figured the angles, ripped the staves and glued it using hose clamps. The clamps are available in the duct section of the borg. The more staves you have the more circular it will be and the thinner the stock can be. I think 3/8" at the thinnest point would be OK. I glued the plywood ends in mine and used them to mount it on the lathe. I can explain how I perfected the angles if you care to ask.

Re: Pedestal Technique Take 2

#5

Alan Young

Thanks for the comments-

Alan Young

I think I need to revisit my plans-will probably adapt a coopered style to the pedestal

Re: Pedestal Technique Take 2

#6

I sure wouldn't glue on plywood ends!

Dick Coers

Plywood and especially glued plywood, will restrict the expansion and contraction of the solid wood in your layout. You will get a wilder grain look in your pattern compared to stave construction. It also looks like the table will be unstable in the direction perpendicular to your base. The turned column is pretty boring in it's look. Normally, you would have a larger diameter in the base for a visual balance. Keeping the top and bottom diameters the same will not be too pleasing to look at.

Re: Pedestal Technique Take 2

#7

Re: Thanks for the comments- *LINK*

Grant in Iowa

Suggest you draw it up in CAD as you have done with solution "A" to establish the required thickness of your staves. The more staves, the thinner they can be.

What I have seen is a solid wood cross bar that truncates the cylinder to allow the top to attach firmly. Short of that, I am not sure how you affix the top, unless you do some long all-thread.

Here's a handy spreadsheet tool I googled up for you to make the brain work of figuring the coopering part easier:


Coopering calculations

Re: Pedestal Technique Take 2

#8

Rethinking my answer.....

Barry Irby

I said I glued in plywood ends. I was wrong. I rabbeted the ends of the staves before assembly and then put in a cross piece as I recall about 2 inches wide and an inch thick. I used that to mount the column on the lathe and turn it. I attached it with angled screws into the shoulder of the rabbet. After I turned it I drill a hole through the center mark and used an All Thread rod to attach the top to the base.

Re: Pedestal Technique Take 2

#9

Re: Pedestal Technique Take 2

Mark

I second the octagon hollow pedestal idea. I bought an antique round oak table years before i got into wood working and then later on a friend wanted a replica..Never really looked at it before but that is exactly how they had turned the pedestal. 1 inch think stock glued into an octagon and turned.. worked out great lots of strength.