Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Table Top Thickness and wood movement...

Posts

Table Top Thickness and wood movement...

#1

Alan Young

Table Top Thickness and wood movement...

Alan Young

I am working on a Table design where the top is 50" x 30" and a total final thickness of 1.5" but I'd like to avoid using that 1.5" through out the top--I would start with a surface of .75" thick(probably Cherry) edge glued pieces of 4" to 6" wide....


add a second layer underneath of .75" thick boards-along the side the pieces run the full length-across the ends they are about 4-6"long but maintain the same grain direction---


Yielding a finished "view able" look something like this:


There has been some interesting posts recently regarding moisture loss along the length of glue line etc..aesthetics aside--.I am wondering if there are any wood potential movement issues in this ?

Re: Table Top Thickness and wood movement...

#2

I've done that before without any problem.

Keith Newton

If you start with longer stock than you need, then after it is edge glued, the ends which get cut off can be folded under and glued on, for a book-match look, or just dropped down and slid under, for a slip match look.

Re: Table Top Thickness and wood movement...

#3

Me too

Lee Schierer in McKean, PA

I've done the same thing. By cutting off the ends of longer boards and folding them under on each end allows you to get perfect color match with each board making the double thickness harder to detect.

Lee

Re: Table Top Thickness and wood movement...

#4

An idea

Bill Tindall, E.Tn.

"Bookmatched" end grain looks neat. It can make "eyes" from flat sawed lumber. When preparing the boards for gluing into the panel cut an end off and then rotate it back onto the bottom of the board and glue it in place, each end. Then assemble panels. The end of the table will appear as eyes along the edge. I think the effect would be striking.


Re: Table Top Thickness and wood movement...

#5

Re: Table Top Thickness and wood movement...

don stephan

Flat sawn cherry can have a lot of sapwood, which may or may not be the look you are seeking. You might also price rift and quartered cherry which doesn't have a lot of sap.

Re: Table Top Thickness and wood movement...

#6

Re: Table Top Thickness and wood movement...

John in NM

That is exactly what I was trying to describe in another thread. A shop I used to work for did that, the pieces that were added below were offcuts from the top itself so that the end grain appeared book matched. It wasn't to my taste, personally, but no one ever asked me :D

Re: Table Top Thickness and wood movement...

#7

Veneer?

Joe Burke

Is veneer over a 3/4" substrate with a 1 1/2" thick edging all around an option? Or is using solid important above all else?

Just wondering I suppose.

Re: Table Top Thickness and wood movement...

#8

Re: Table Top Thickness and wood movement...

Barry Irby

I made a side board out of old Heart Pine that was very close grained. I was struggling to get enough material out of several old beams I had. I made the blunder of sending one of the boards for the top through my planer after I set a knife wrong and took off much more than I intended. To compensate I folded the ends and sides back under as discussed above and then cut a long bevel on it to make the joint right at the transition. Looks good, no one has ever noticed and it has held up well for about five years so far. I can post a picture if you want.

Re: Table Top Thickness and wood movement...

#9

Alan Young

Thanks for all the help---

Alan Young

glad to know this will work. Still not sure what I'll end up doing. I may use veneer over a thicker substrate -or even use full thickness of solid wood. But I am glad to know there is this option....

-Alan