Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Back in December, Mr. Tindall...

Posts

Back in December, Mr. Tindall...

#1

Back in December, Mr. Tindall...

Joe in a Cleveland suburb

did a review of the Grace screwdrivers. I wanted a set. My wife bought the set of straight and phillips for me for my birthday.

Amazing. What a difference to have the screwdriver actually fit the slot tightly. Wow. Thanks for the review Bill.

Now I need a decent way to hang them over my workbench. Right now I have one of those crappy screwdriver holder things that attached to peg board. You know what I'm talking about; one of those hanger things that every time you touch it it comes unattached from the peg board and falls off...

http://www.woodcentral.com/woodworking/forum/messages.pl?pro=search;pmd=sread;srchid=30223mOfOZsZTKqMLGeH1392039774;spage=1;sanc=474227;sbid=1000;md=read;id=474227#m_474227

Re: Back in December, Mr. Tindall...

#2

Jack Guzman from Maine

Re: Back in December, Mr. Tindall...

Jack Guzman from Maine

Screwdriver hangers are easy. All I do is drill appropriate sized holes in a narrow shelf.---Jack

Re: Back in December, Mr. Tindall...

#3

Re: Back in December, Mr. Tindall...

Dustmaker Mike

Well you could use small zip ties to hold it on that is what I do in my garage.

Re: Back in December, Mr. Tindall...

#4

Re: Back in December, Mr. Tindall...

William Duffield, on the Cohansey

Wooden shelves, boxes, and brackets to fit pegboard are easy to make, but do require a little fiddling to get them to work well. You could just screw and glue them to the pegboard, but that kinda defeats the purpose of the pegboard ;^). I usually make my own hooks to fit the brackets, from a pair of FHWSs. Don't use drywall screws, because they are too brittle and can't be bent to the requisite shapes. I drill two holes in the top rear edge of the bracket, a precise number of inches apart, at about a 45° angle downward (so I don't split the bracket), drive in the screws to prethread the holes, and mark the screw depth. I then remove the screws, clamp them (individually) in a machinist's vise, cut off their heads, bend them about 45° at the mark, bend them back 90° a quarter inch or so beyond the mark, and trim them to length about a half inch beyond the second mark. I usually used a hammer or a pair of vise-grips to do the bending. I then screw them back into the wooden bracket and do some fine adjusting so they slip smoothly into the peg board. To mount them, I tilt the bracket up 45° at the front, insert the hooks and push them in while rotating the bracket back down into position (just like you would with the flimsy wire brackets. I prefer to use screws with a limited length of thread and a long length of unthreaded shaft, so I don't have to file away the threads. You could also start with a 90° cup hook.

Sorry I don't have convenient access right now to a method to either photograph or make a drawing of my installation and post it here on WoodCentral, but maybe later this week, if my verbal description was only as clear as mud.

Re: Back in December, Mr. Tindall...

#5

Re: Back in December, Mr. Tindall...

David Yoho

After reading Bill's review I also bought a set of the slotted. I am short on wall space so I solved the storage issue another way. I made one to hold my new toys. I had some 100+ year old heart pine screaming to become a box. I posted these earlier but here they are again -



Re: Back in December, Mr. Tindall...

#6

Re: CRS Syndrome Kicks In Again :^(

William Duffield, on the Cohansey

I'm back in the shop, to take some pics of the mounts. Making and installing the hooks is a lot simpler than I remembered. The screws only need one bend, and 90° cup hooks work very well, with only one cut, but are a bit more expensive than screws, which might be important if you have a whole wall of tool holders to hang. When I bend the #8 screws, they naturally bend to an inside radius of about 1/8" and an outside radius of about 1/4". Halving that distance, drill a horizontal pilot hole centered about 3/16" from the top of the back face of the bracket (or box). Make one almost 90° bend in the screw, and cut the head off about 1/8" above the top of the bracket. When you drive the hook, thus formed, into the back of the bracket, stop when the gap between the hook and the back of the bracket is about 1/8" (the thickness of the pegboard).

Sorry for the temporary misinformation.